14.2: Pressure as a Function of Depth

Physics: A Foundation for Scientists and Engineers · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    14.2: Pressure as a Function of Depth

    Dive to the bottom of a pool and your ears feel the increase at once: pressure grows with depth. The reason is the weight of the fluid overhead, and a free-body diagram makes it exact. Picture an imaginary cylinder of fluid of cross-sectional area \(A\), reaching from the surface (where the pressure is \(P_0\)) straight down to a depth \(h\). That cylinder is at rest, so the vertical forces on it must balance. The fluid beneath pushes up on its base with force \(PA\); the air and fluid above push down on its top with \(P_0 A\); and gravity pulls down on the fluid inside it with weight \(\rho (Ah) g\). Setting the upward force equal to the downward ones,

    \[PA = P_0 A + \rho A h g,\]

    and dividing through by \(A\) gives

    Key Equation: Pressure with depth

    \[P = P_0 + \rho g h. \tag{14.3}\]

    Two connected fluid columns of different shape.
    Figure 14.1. Pressure in a fluid depends on depth, not volume. The pressure at the bottom of the deep narrow column (\(h_2\)) is greater than at the bottom of the shallow wide one (\(h_1\)), even though the wide tank holds roughly twice as much water.
    Figure descriptionTwo connected fluid columns of different shape. The shallow wide column has a smaller depth h sub 1 and lower pressure at its base, while the deep narrow column has a greater depth h sub 2 and higher pressure at its base. Pressure depends on depth, not on the volume of fluid.

    Notice what dropped out. The area \(A\) canceled, so the result holds for a column of any width, and nothing in the derivation referred to the shape of the container. Pressure depends only on the vertical depth below the surface, not on the shape or total volume of the fluid (Figure 14.1): the pressure at the bottom of a narrow deep pond exceeds that at the bottom of a broad shallow lake, even though the lake holds far more water.

    Two consequences deserve to be stated on their own, because nearly every fluid-statics problem leans on one of them.

    • Equal depths, equal pressures. Any two points at the same height within a single connected body of fluid at rest are at the same pressure. If they were not, the fluid between them would be pushed from the higher pressure toward the lower, and then it would not be at rest. This is what lets us carry a pressure around a corner: down one arm of a U-tube and up the other, or from the small piston of a hydraulic lift across to the large one.
    • Only vertical distance counts. In \(\rho g h\), the quantity \(h\) is the vertical drop, not the distance traveled through the fluid. The water at the bottom of a \(10\,\mathrm{m}\) vertical pipe and the water at the bottom of a \(50\,\mathrm{m}\) pipe that slopes down through the same \(10\,\mathrm{m}\) of elevation are at exactly the same pressure.

    The pressure that equation (14.3) returns is the absolute pressure, measured up from a perfect vacuum. Most instruments do not report it. A tire gauge, a blood-pressure cuff, and the dial on a scuba tank all measure the amount by which the fluid’s pressure exceeds the surrounding atmosphere, called the gauge pressure:

    \[P_{\rm gauge} = P_{\rm abs} - P_{\rm atm}. \tag{14.4}\]

    A flat tire reads zero on a gauge but still holds air at about \(1\,\mathrm{atm}\) absolute. For a liquid whose surface is open to the air, \(P_0 = P_{\rm atm}\), and the gauge pressure at depth \(h\) is exactly \(\rho g h\). Watch for which one a problem wants: “find the pressure at the bottom of the pool” is ambiguous, and the two answers differ by a full atmosphere.

    Example 14.2: Water pressure in a house

    The main water line enters a house on the first floor at a gauge pressure of \(2.86\times 10^{5}\,\mathrm{Pa}\). (a) A faucet on the second floor sits \(7.10\,\mathrm{m}\) above the line and is turned off. What is the gauge pressure there? (b) How high could a faucet be before no water would reach it at all?

    Solution

    Both parts use equation (14.3) with one adjustment: here the known pressure is at the bottom of the column and we are moving up, so the \(\rho g h\) term is subtracted rather than added. To keep that straight, write \(P_{\rm line}\) for the pressure at the main and \(P_{\rm faucet}\) for the pressure a height \(h\) above it; do not reuse \(P_0\), which in equation (14.3) is the pressure at the top. Both are gauge pressures measured against the same atmosphere, so we may work in gauge values throughout.

    (a) The higher faucet has less fluid weight above it, or, equivalently, the line must push water up \(7.10\,\mathrm{m}\) to reach it. First compute the pressure of a \(7.10\,\mathrm{m}\) water column:

    \[\rho g h = (1000\,\mathrm{kg/m^3})(9.8\,\mathrm{m/s^2})(7.10\,\mathrm{m}) = 6.96\times 10^{4}\,\mathrm{Pa}.\]

    (The units: \(\,\mathrm{kg/m^3}\cdot\,\mathrm{m/s^2}\cdot\,\mathrm{m} = \,\mathrm{kg/(m\cdot s^2)} = \,\mathrm{N/m^2} = \,\mathrm{Pa}\).) Subtract it from the line pressure, writing both over the same power of ten:

    \[P_{\rm faucet} = P_{\rm line} - \rho g h = 2.86\times10^5 - 0.696\times10^5 \approx \boxed{2.16\times 10^{5}\,\mathrm{Pa}}.\]

    (b) Water just fails to reach a faucet when the gauge pressure there falls to zero. Set \(P_{\rm line} - \rho g h_{\max} = 0\), add \(\rho g h_{\max}\) to both sides, and divide by \(\rho g\):

    \[h_{\max} = \frac{P_{\rm line}}{\rho g} = \frac{2.86\times10^5\,\mathrm{Pa}}{(1000\,\mathrm{kg/m^3})(9.8\,\mathrm{m/s^2})} = \frac{2.86\times10^5}{9800}\,\mathrm{m} \approx \boxed{29.2\,\mathrm{m}}.\]

    No faucet higher than about \(29\,\mathrm{m}\) (roughly a ten-story building) could be fed by this line alone. One caution about that number: it is a static result, telling you how high the water would stand with every tap closed. Water that is actually flowing loses further pressure to friction in the pipes, so the practical limit is lower. This is why tall buildings need booster pumps or rooftop tanks.

    Equation (14.3) also tells us the force on a submerged surface, but that force is not simply pressure times area, because the pressure is not the same everywhere on the surface. It grows linearly with depth, so we integrate.

    Example 14.3: Force on a dam

    A dam holds fresh water to a depth \(H = 12\,\mathrm{m}\) against a vertical face of width \(w = 30\,\mathrm{m}\). Find the total force the water exerts on the dam.

    Solution

    Step 1: Why an integral? If the pressure were the same everywhere on the face we could write \(F = PA\). It is not: pressure grows with depth. So divide the wetted face into horizontal strips, each thin enough that the pressure across it is essentially uniform. A strip at depth \(y\) below the surface, of thickness \(dy\), has area \(dA = w\,dy\) and feels a gauge pressure \(\rho g y\). The force on that strip is

    \[dF = P\,dA = (\rho g y)(w\,dy).\]

    Atmospheric pressure is omitted because it also acts on the dry side of the dam and cancels.

    Step 2: Add up the strips. The total force is the integral from the surface (\(y = 0\)) down to the base (\(y = H\)). The constants \(\rho\), \(g\), and \(w\) come outside, and by the power rule \(\int y\,dy = y^2/2\):

    \[F = \int_0^H \rho g w\, y\,dy = \rho g w\left[\frac{y^2}{2}\right]_0^H = \rho g w\left(\frac{H^2}{2} - 0\right) = \tfrac{1}{2}\rho g w H^2.\]

    Step 3: Substitute. Square the depth first:

    \[\begin{aligned}F &= \tfrac{1}{2}(1000\,\mathrm{kg/m^3})(9.8\,\mathrm{m/s^2})(30\,\mathrm{m})(12\,\mathrm{m})^2 \\ &= \tfrac{1}{2}(1000)(9.8)(30)(144)\,\mathrm{N} \approx \boxed{2.1\times 10^{7}\,\mathrm{N}}.\end{aligned}\]

    That is about \(2100\) tonnes of force.

    Check. Rewrite the result as \(\left(\rho g\,\tfrac{H}{2}\right)(wH)\): the pressure at mid-depth times the total area. Numerically, \(\rho g (H/2) = (1000)(9.8)(6.0) = 5.9\times 10^{4}\,\mathrm{Pa}\) and \(wH = 360\,\mathrm{m^2}\), giving \(2.1\times 10^{7}\,\mathrm{N}\). ✓ The pressure rises linearly from zero, and the average of a linear distribution is its midpoint value. Note also the \(H^2\): doubling the depth quadruples the force, which is why dam walls are built thick at the bottom and thin at the top.

    Designing the dam takes one more piece of information: where that resultant acts. Because the pressure loading is triangular, the resultant acts one third of the way up from the base, at \(H/3\), a torque calculation of the kind you met in Chapter 12.

    We live at the bottom of an ocean of air, so we too feel a fluid’s weight. The atmosphere, whose bulk lies within about \(100\,\mathrm{km}\) of the ground, presses on us with an atmospheric pressure of about \(1.0\times 10^{5}\,\mathrm{Pa}\) (\(\approx 15\,\mathrm{psi}\), or \(750\,\mathrm{mmHg}\)). We are not crushed because our bodies maintain an equal internal pressure that pushes back.

    Note: Do not use \(P = P_0 + \rho g h\) on the atmosphere

    The derivation above assumed the density \(\rho\) is the same everywhere in the column. That is excellent for a liquid, which is nearly incompressible: seawater at the bottom of the deepest trench is only about \(5\%\) denser than at the surface. It fails badly for a gas, which compresses under its own weight. Air at sea level has \(\rho = 1.29\,\mathrm{kg/m^3}\), but at an altitude of \(10\,\mathrm{km}\) it is about a third of that. Applying the formula to a \(100\,\mathrm{km}\) column of sea-level air would give \(\rho g h = (1.29)(9.8)(1.0\times10^5) \approx 1.3\times 10^{6}\,\mathrm{Pa}\), roughly \(13\) atmospheres: more than ten times the true value. Real atmospheric pressure falls off approximately exponentially, dropping by a factor of \(e\) about every \(8.5\,\mathrm{km}\).

    Checkpoint 14.2

    A student objects: “The pressure at the bottom of a \(10\,\mathrm{m}\) pipe of \(2\,\mathrm{cm}\) diameter can’t be as large as at the bottom of a \(10\,\mathrm{m}\) pool; the pipe holds only a few liters of water, and the pool holds hundreds of tonnes.” Identify the confusion, and use the free-body derivation to say precisely what the extra water in the pool is being supported by, if not by the water at the bottom. Then answer this: a reservoir behind a dam is \(40\,\mathrm{m}\) deep and \(5\,\mathrm{km}\) long; a second reservoir is \(40\,\mathrm{m}\) deep and \(200\,\mathrm{m}\) long. Do their dams need to be built to the same strength? (Careful: “strength” involves both pressure and total force.)

    Answer

    Answers to Checkpoints

    Checkpoint 14.2. The confusion is between pressure and total weight. The pressure at depth \(h\) is \(\rho g h\) however wide the container is: the free-body derivation balances the weight of a column of water directly above a small area at the bottom, and a column \(10\,\mathrm{m}\) tall has the same weight per unit area whether it stands in a pipe or in a pool. The rest of the pool’s water is not pressing on that spot at all; it rests on the rest of the pool floor, which supports it. The two dams need the same strength per meter of their width: the pressure at every depth, and hence the force on each strip of the dam’s face, depends only on the depth (\(40\,\mathrm{m}\) in both), not on how far the water extends behind the dam. Total force does depend on the dam’s width across the valley, \(F = \tfrac{1}{2}\rho g wH^2\), but the reservoir’s length appears nowhere.


    This page titled 14.2: Pressure as a Function of Depth was last modified on Thu, 12 Nov 2026 04:26:44 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.