14.1: Fluids, Density, and Pressure

Physics: A Foundation for Scientists and Engineers · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    14.1: Fluids, Density, and Pressure

    A fluid is any substance that flows and conforms to the shape of its container, both liquids and gases. To describe how much matter a fluid packs into a region, we use its density, the mass per unit volume:

    Key Equation: Density

    \[\rho = \frac{m}{V}. \tag{14.1}\]

    Density is measured in \(\,\mathrm{kg/m^3}\). Water has \(\rho = 1000\,\mathrm{kg/m^3}\), while air at \(0\,^{\circ}\mathrm{C}\) and \(1\,\mathrm{atm}\) is about \(1.29\,\mathrm{kg/m^3}\): some \(800\) times less. That qualifier matters: a liquid’s density barely budges with pressure or temperature, but a gas compresses readily, so a gas density is meaningless unless the conditions are stated (the same air at \(20\,^{\circ}\mathrm{C}\) has \(\rho \approx 1.2\,\mathrm{kg/m^3}\)). Differences in density are what make oil float on water and a hot-air balloon rise.

    When a fluid pushes on a surface, what matters is not just the force but how it is spread out. Pressure is the force per unit area exerted perpendicular to a surface:

    Key Equation: Pressure

    \[P = \frac{F}{A}. \tag{14.2}\]

    The SI unit is the pascal (\(\,\mathrm{Pa} = \,\mathrm{N/m^2}\)). A pascal is tiny (a dollar bill lying flat presses on a table with about \(1\,\mathrm{Pa}\)), so real pressures are usually quoted in kilopascals or in one of several older units. One chain of equivalents is worth committing to memory:

    \[1\,\mathrm{atm} = 1.013\times 10^{5}\,\mathrm{Pa} = 760\,\mathrm{mmHg} = 14.7\,\mathrm{psi},\]

    where \(\,\mathrm{psi}\) is pounds per square inch (the unit on a tire gauge) and \(\,\mathrm{mmHg}\), the millimeter of mercury, is also called the torr; blood pressures are reported in it. The same force spread over a larger area gives less pressure, which is exactly why you can lie on a bed of nails unharmed: your weight is divided among so many points that the pressure at any one is bearable.

    One feature of pressure trips students up. We defined it using the force on a surface, but pressure at a point inside a fluid has no direction of its own: a small surface placed at that point feels the same push whichever way it faces. Pressure is a scalar. What is a vector is the force it produces, which is always perpendicular to the surface and directed into it. This is why water pushes sideways on the face of a dam and upward on the underside of a boat’s hull, not merely downward.

    Example 14.1: Pressure under a heel

    A \(55\,\mathrm{kg}\) woman balances all her weight on the tip of one stiletto heel of area \(1.0\,\mathrm{cm^2}\). Find the pressure on the floor, and compare it with a flat shoe of area \(150\,\mathrm{cm^2}\).

    Solution

    Step 1: The force. The force on the floor is her weight, \(F = mg = (55\,\mathrm{kg})(9.8\,\mathrm{m/s^2}) = 539\,\mathrm{N}\).

    Step 2: Convert the area to SI. Pressure in pascals needs the area in square meters. Since \(1\,\mathrm{cm} = 10^{-2}\,\mathrm{m}\), squaring both sides gives \(1\,\mathrm{cm^2} = (10^{-2})^2\,\mathrm{m^2} = 10^{-4}\,\mathrm{m^2}\); the conversion factor must be squared along with the unit, exactly as in Chapter 1. So the heel’s area is \(A = 1.0\times10^{-4}\,\mathrm{m^2}\).

    Step 3: The pressure. \[P = \frac{F}{A} = \frac{539\,\mathrm{N}}{1.0\times10^{-4}\,\mathrm{m^2}} \approx \boxed{5.4\times 10^{6}\,\mathrm{Pa}}.\]

    Dividing by \(10^{-4}\) is the same as multiplying by \(10^{4}\), so the pressure is \(539\times10^4 = 5.39\times10^6\,\mathrm{Pa}\). That is \(5.39\times10^6/1.01\times10^5 \approx 53\) times atmospheric pressure: enough to dent a wooden floor.

    The flat shoe. Spread over \(150\,\mathrm{cm^2} = 150\times10^{-4}\,\mathrm{m^2}\), the same force gives \(P = 539/(1.50\times10^{-2}) = 3.6\times 10^{4}\,\mathrm{Pa}\). Because \(P = F/A\) with \(F\) fixed, pressure is inversely proportional to area: \(150\) times the area means \(1/150\) the pressure. Same force, vastly different pressure.

    Checkpoint 14.1

    A woman in flat shoes and an African elephant stand side by side on soft ground. Decide which is more likely to sink in, and state exactly what you would need to look up to be sure. Then sharpen it: an elephant weighs roughly \(60\) times what the woman does, but spreads that weight over four feet whose total contact area is only about \(20\) times larger than her two soles. By what factor do the two pressures differ, and which way? (Hint: you are comparing \(F/A\), so the two ratios do not cancel; they compete.)

    Answer

    Answers to Checkpoints

    Checkpoint 14.1. Sinking depends on pressure, \(P = F/A\), not on weight alone, so you would need each one’s weight and the total area of the feet or soles in contact with the ground. With the numbers given, the elephant’s pressure is larger by \(60/20 = 3\): its weight is \(60\) times larger, but its contact area is only \(20\) times larger, so the weight ratio wins. The elephant presses on the ground about three times harder per square meter and is the more likely to sink in. (A woman in stiletto heels would reverse the result: see the example “Pressure under a heel,” where the heel’s tiny area gives a pressure far above an elephant’s.)


    This page titled 14.1: Fluids, Density, and Pressure was last modified on Thu, 12 Nov 2026 04:26:44 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.