14.3: Pascal’s Principle

Physics: A Foundation for Scientists and Engineers · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    14.3: Pascal’s Principle

    What happens if we squeeze a confined fluid? Because a fluid flows, any increase in pressure at one point is passed along to every other point. This is Pascal’s principle: a pressure change applied to an enclosed fluid is transmitted undiminished to every part of the fluid and to the walls of its container.

    The principle is the basis of all hydraulic machines: car brakes, lifts, and presses. Apply a force \(F_1\) to a small piston of area \(A_1\), and the pressure \(P = F_1/A_1\) appears throughout the fluid, including at a large piston of area \(A_2\), where it produces a force \(F_2 = P A_2\). Equating the pressures gives

    Key Equation: Pascal’s principle (hydraulics)

    \[\frac{F_1}{A_1} = \frac{F_2}{A_2}. \tag{14.5}\]

    Hydraulic lift: a small force on a narrow piston produces a large force on a wide piston.
    Figure 14.2. A hydraulic lift. A small force \(F_1\) on the narrow piston creates a pressure transmitted through the connected fluid to the wide piston, where it produces a much larger force \(F_2 = F_1 (A_2/A_1)\). The two pistons are drawn at the same level, so the pressures at their faces are equal.
    Figure descriptionA hydraulic lift. A small force F sub 1 acts on a narrow piston of area A sub 1, and the pressure transmitted through the connected fluid produces a much larger force F sub 2 on a wide piston of area A sub 2.

    A small force on a small piston balances a large force on a large piston, in proportion to the areas: a multiplication of force, the hydraulic version of the lever (Figure 14.2).

    Example 14.4: A hydraulic lift

    The small piston of a hydraulic lift has area \(5.0\,\mathrm{cm^2}\); the large piston has area \(250\,\mathrm{cm^2}\). What force on the small piston is needed to support a \(5000\,\mathrm{N}\) car on the large one?

    Solution

    By Pascal’s principle, the pressure is the same under both pistons, \(P_1 = P_2\). Writing each pressure as force over area (equation (14.5)),

    \[\frac{F_1}{A_1} = \frac{F_2}{A_2}.\]

    Multiply both sides by \(A_1\) to isolate \(F_1\):

    \[F_1 = F_2\,\frac{A_1}{A_2} = (5000\,\mathrm{N})\,\frac{5.0\,\cancel{\mathrm{cm^2}}}{250\,\cancel{\mathrm{cm^2}}} = (5000\,\mathrm{N})(0.020) = \boxed{100\,\mathrm{N}}.\]

    Only the ratio of the areas matters, so the square centimeters cancel and there is no need to convert to square meters.

    A \(100\,\mathrm{N}\) push (about the weight of a \(10\,\mathrm{kg}\) sack of flour) holds up a car, because the large piston has \(250/5.0 = 50\) times the area. (The force is multiplied, but the small piston must move \(50\) times as far: the fluid volume pushed out of the small cylinder, \(A_1 d_1\), must equal the volume pushed into the large one, \(A_2 d_2\). The work in, \(F_1 d_1\), therefore equals the work out, \(F_2 d_2\): energy is conserved.)

    Note: The two pistons should be at the same height

    Equation (14.5) sets the pressures at the two piston faces equal, which is exactly true only when they are at the same level. If the output piston sits a height \(d\) above the input piston, the pressure there is lower by \(\rho g d\), and \(F_2 = \left(F_1/A_1 - \rho g d\right)A_2\). For a garage lift with \(d \approx 1.5\,\mathrm{m}\) of hydraulic oil (\(\rho \approx 850\,\mathrm{kg/m^3}\)), that correction is about \(1.2\times 10^{4}\,\mathrm{Pa}\) against working pressures of \(1\times 10^{7}\,\mathrm{Pa}\) or more: roughly \(0.1\%\), which is why it is normally ignored. In a tall system it is not: the water column feeding a high-rise, or a hydraulic line running several stories, has to be designed around it.

    Checkpoint 14.3

    A hydraulic lift’s input piston has \(1/50\) the area of its output piston. A student proposes shrinking the input piston until the ratio is \(1/100\), so that the same push lifts twice the load, and asks why lifts are not simply built this way. Say what the change costs (be quantitative about the distance the operator’s piston must travel) and identify a practical limit that has nothing to do with energy. Then explain a related point: hydraulic systems use oil rather than air, and mechanics “bleed” brake lines to chase out every bubble. What goes wrong if a little air is trapped in the line, given that Pascal’s principle applies to gases too? (Hint: the principle transmits the pressure faithfully; what it does not promise is that the fluid keeps its volume.)

    Answer

    Answers to Checkpoints

    Checkpoint 14.3. With a \(1/100\) area ratio the output force doubles, but the fluid volume is unchanged, so the input piston must travel \(100\) times as far as the load rises, instead of \(50\). The work in still equals the work out; the operator simply pushes half as hard for twice the distance. The practical limit is that stroke: lifting a car \(2\,\mathrm{m}\) would take \(200\,\mathrm{m}\) of piston travel, meaning an absurdly long cylinder or a great many pump strokes, with seals and leakage losses on every one. Trapped air ruins the system because air is compressible. Pascal’s principle still transmits the pressure, but when you push the pedal the bubble shrinks instead of the liquid moving. The pedal travels without moving the brake pads until the air is squeezed down, giving the familiar “spongy” brakes. Liquids are nearly incompressible, so a push on one end moves the other end at once.


    This page titled 14.3: Pascal’s Principle was last modified on Thu, 12 Nov 2026 04:26:44 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.