12.3: Elasticity

Physics: A Foundation for Scientists and Engineers · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    12.3: Elasticity

    No real object is perfectly rigid. Apply forces to a solid and it deforms: a little or a lot, reversibly or permanently. Elasticity is the study of how solids change shape under load and spring back when the load is removed. The central idea is a proportionality, within limits, between the stress applied (force per unit area) and the resulting strain (fractional deformation). Their ratio is a property of the material called an elastic modulus:

    \[\text{elastic modulus} = \frac{\text{stress}}{\text{strain}}.\]

    This is Hooke’s law generalized from springs to materials: double the stress and you double the strain, until the elastic limit is reached and the material yields or breaks.

    Bar of length L and area A stretched by delta L under equal and opposite forces F.
    Figure 12.2. Tensile stress and strain. A force \(F\) applied to a bar of cross-sectional area \(A\) and length \(L\) stretches it by \(\Delta L\). Young’s modulus is the ratio of the stress \(F/A\) to the strain \(\Delta L/L\).
    Figure descriptionA bar of length L and cross-sectional area A pulled by equal and opposite forces F at each end, stretching it by an amount delta L.

    There are three common deformations, each with its own modulus. For stretching or compressing along a length (Figure 12.2), Young’s modulus \(Y\) relates the tensile stress \(F/A\) to the fractional change in length \(\Delta L/L\):

    Key Equation: Young’s modulus

    \[Y = \frac{F/A}{\Delta L/L}. \tag{12.4}\]

    Two panels showing shear and volume deformation.
    Figure 12.3. The other two deformations. (a) In shear, the force acts parallel to a face of area \(A\), sliding it a distance \(\Delta x\) relative to a face \(h\) away; the dashed outline is the undeformed shape, and the strain \(\Delta x/h\) equals \(\tan\theta\). (b) Under a uniform pressure increase \(\Delta P\) the object shrinks from volume \(V\) to \(V - \Delta V\) without changing shape. Both deformations are drawn greatly exaggerated.
    Figure descriptionTwo panels showing shear and volume deformation. In shear, a force parallel to a face of area A slides it a distance delta x relative to the opposite face across height h. In volume deformation, pressure acts inward on all faces, reducing the volume.

    Stress has units of pascals (\(\,\mathrm{Pa} = \,\mathrm{N/m^2}\)), and strain is dimensionless, so the moduli are measured in pascals. Young’s modulus is large for stiff materials (about \(2\times 10^{11}\,\mathrm{Pa}\) for steel), meaning enormous stress is needed for even a slight stretch. The other two cases follow the same pattern. The shear modulus \(S\) governs a sideways deformation. Here the force \(F\) is applied parallel to a face of area \(A\) rather than perpendicular to it, sliding that face a distance \(\Delta x\) relative to a parallel face a distance \(h\) away, so that the object’s square cross-section becomes a parallelogram (Figure 12.3a):

    Key Equation: Shear modulus

    \[S = \frac{F/A}{\Delta x/h}. \tag{12.5}\]

    Note that \(A\) here is the area of the face the force acts along, not the area it acts across. The shear strain \(\Delta x/h\) is the tangent of the small angle through which the sides tilt, so for the tiny deformations of stiff materials it is simply that angle in radians.

    And the bulk modulus \(B\) governs uniform compression, in which pressure is applied over the entire surface and the object shrinks without changing shape (Figure 12.3b). It relates the change in pressure \(\Delta P\) to the fractional change in volume:

    Key Equation: Bulk modulus

    \[B = -\frac{\Delta P}{\Delta V/V}. \tag{12.6}\]

    The minus sign makes \(B\) positive, since an increase in pressure decreases the volume. A liquid or gas has a bulk modulus but no Young’s or shear modulus: a fluid at rest cannot sustain a tension or a static shear, which is exactly what makes it flow. Solids have all three.

    Table 12.1 collects representative values. Two patterns are worth noticing. First, for a given solid the three moduli are of the same order of magnitude, with \(S\) typically a third to a half of \(Y\). Second, the range across materials is enormous (steel is about seventy times stiffer than nylon), which is why material choice, not just geometry, decides how much a structure deflects.

    Table 12.1. Approximate elastic moduli for selected materials. Values vary with composition, temperature, and processing, so treat these as representative rather than exact. Liquids have no Young’s or shear modulus because they cannot sustain a static tension or shear. Concrete’s Young’s modulus is quoted in compression; in tension it is far weaker and cracks at low stress, which is why structural concrete is reinforced with steel.
    Material\(\boldsymbol{Y}\) (Pa)\(\boldsymbol{S}\) (Pa)\(\boldsymbol{B}\) (Pa)
    Tungsten\(3.5\times10^{11}\)\(1.4\times10^{11}\)\(2.0\times10^{11}\)
    Steel\(2.0\times10^{11}\)\(8.4\times10^{10}\)\(1.6\times10^{11}\)
    Copper\(1.1\times10^{11}\)\(4.4\times10^{10}\)\(1.4\times10^{11}\)
    Brass\(9.0\times10^{10}\)\(3.5\times10^{10}\)\(6.0\times10^{10}\)
    Aluminum\(7.0\times10^{10}\)\(2.5\times10^{10}\)\(7.0\times10^{10}\)
    Glass\(6.5\times10^{10}\)\(2.6\times10^{10}\)\(5.0\times10^{10}\)
    Concrete\(2.0\times10^{10}\)——
    Bone (compact)\(1.6\times10^{10}\)——
    Nylon\(3.0\times10^{9}\)——
    Water——\(2.2\times10^{9}\)
    Mercury——\(2.8\times10^{10}\)

    Finally, notice what Young’s modulus says about an object rather than a material. Solving equation (12.4) for the force gives

    \[F = \left(\frac{YA}{L}\right)\Delta L,\]

    which is exactly Hooke’s law \(F = k\,\Delta L\) with an effective spring constant

    \[k = \frac{YA}{L}. \tag{12.7}\]

    Every rod, wire, and cable is a stiff spring. The modulus \(Y\) belongs to the material; the stiffness \(k\) belongs to the particular piece, and grows with its cross-section and shrinks with its length. This is why a long cable sags more than a short one of the same steel, and it lets us carry over everything we know about springs, including the rule that springs joined end to end add as \(1/k = 1/k_1 + 1/k_2\).

    Checkpoint 12.4

    An engineer replaces a support wire with one of the same material and length but twice the diameter, carrying the same load. By what factor does each of the following change: the stress in the wire, the strain, the elongation, and the effective spring constant \(k\)? Which of these four quantities, if any, is a property of the material rather than of this particular wire?

    Answer

    Example 12.7: Stretch of a steel rod

    A steel support rod \(2.0\,\mathrm{m}\) long with a cross-sectional area of \(3.0\times 10^{-4}\,\mathrm{m^2}\) carries a \(1500\,\mathrm{kg}\) load. Taking \(Y_{\rm steel} = 2.0\times 10^{11}\,\mathrm{Pa}\), find how much it stretches.

    Solution

    Step 1: The force. The rod supports the load, so the tensile force equals the load’s weight: \(F = mg = (1500\,\mathrm{kg})(9.8\,\mathrm{m/s^2}) = 14700\,\mathrm{N}\).

    Step 2: Rearrange Young’s modulus. Equation (12.4) defines \(Y\) as stress over strain, \(Y = (F/A)/(\Delta L/L)\). Dividing by a fraction is multiplying by its reciprocal, so this is \(Y = FL/(A\,\Delta L)\). To isolate \(\Delta L\), multiply both sides by \(\Delta L\) and divide both sides by \(Y\):

    \[Y\,\Delta L = \frac{FL}{A} \;\Longrightarrow\; \Delta L = \frac{FL}{AY}.\]

    Step 3: Substitute. Work out the numerator and denominator separately, collecting powers of ten in the denominator (\(10^{-4} \times 10^{11} = 10^{7}\)):

    \[\Delta L = \frac{(14700\,\mathrm{N})(2.0\,\mathrm{m})}{(3.0\times10^{-4}\,\mathrm{m^2})(2.0\times10^{11}\,\mathrm{Pa})} = \frac{29400\,\mathrm{N\cdot m}}{6.0\times10^{7}\,\mathrm{N}} \approx 4.9\times 10^{-4}\,\mathrm{m} \approx \boxed{0.49\,\mathrm{mm}}.\]

    (A pascal is \(\,\mathrm{N/m^2}\), so \(\,\mathrm{m^2}\cdot\,\mathrm{Pa} = \,\mathrm{N}\), and the units reduce to meters.)

    Half a millimeter under a load of \(1500\,\mathrm{kg}\): a vivid reminder of how stiff steel is, and why it carries our buildings and bridges. It is worth checking that we are entitled to use equation (12.4) at all: the stress here is \(F/A = 14700/(3.0\times10^{-4}) = 4.9\times 10^{7}\,\mathrm{Pa}\), roughly a fifth of the stress at which structural steel begins to yield, so the rod is comfortably in its elastic range and the linear relation holds.

    Beyond the elastic limit

    A stress-strain curve for a ductile metal loaded to fracture.
    Figure 12.4. Stress versus strain for a ductile metal loaded to fracture. The initial straight portion is the elastic region of equation (12.4), and its slope is Young’s modulus. Past the elastic limit the deformation is partly permanent; the material then yields, strain hardens to its ultimate strength, necks down, and breaks. The strain axis is greatly compressed: for steel the elastic region occupies well under one percent strain, while the plastic region can run to twenty percent or more.
    Figure descriptionA stress-strain curve for a ductile metal loaded to fracture. It rises as a straight line of slope Y through the elastic region to the proportional limit and elastic limit, then bends over at the yield point, continues to a maximum at the ultimate strength, and falls to fracture.

    Everything above has assumed that stress and strain stay proportional. Figure 12.4 shows what actually happens when a ductile metal (mild steel, say) is pulled steadily until it breaks. The linear behavior we have been using is only the first stretch of the story.

    The curve starts as a straight line whose slope is \(Y\), and stays straight up to the proportional limit. Beyond that point stress and strain are no longer proportional and equation (12.4) no longer applies. Slightly further along lies the elastic limit. Up to there the specimen still springs back to its original length when the load is removed; past it, it does not. Unload a specimen that has been stretched into that region and it relaxes along a line parallel to the original straight portion, coming to rest at a nonzero strain: a permanent set. This is the difference between bending a paper clip slightly, which does nothing, and bending it firmly, which leaves it bent.

    Just past the elastic limit a ductile metal yields: it deforms a great deal with almost no increase in stress, producing the flat stretch of the curve. The stress at which this begins, the yield strength, is usually the number a designer cares about, since a beam that has yielded is permanently deformed even though it has not broken. Beyond the yield region the metal stiffens again (strain hardening) and the stress climbs to a maximum, the ultimate strength. After that the specimen thins locally, or necks, and the curve falls until it fractures.

    Not all materials behave this way. Glass, cast iron, and concrete loaded in tension are brittle: they have almost no plastic region and fracture at or near the elastic limit, with little warning. Ductile materials announce trouble by deforming visibly first, which is one reason structural steel rather than cast iron carries our bridges.

    Engineers do not design a member to sit anywhere near these limits. The yield strength (or sometimes the ultimate strength) is divided by a safety factor (commonly between 2 and 10, depending on how well the loads are known, how variable the material is, and how serious a failure would be) to give an allowable working stress, and the member is sized so that the actual stress stays below it. The rod of Example 12.7 carries about a fifth of its yield stress, a safety factor of roughly 5.

    Checkpoint 12.5

    A wire is stretched to a strain just past its elastic limit and then completely unloaded. Sketch the loading and unloading paths on a stress–strain diagram. Is the wire now longer than it started? If you reload it, at roughly what stress does it begin to deform plastically again: the original yield strength, or a higher one? What does your answer say about why cold-working a metal makes it harder?

    Answer

    Answers to Checkpoints

    Checkpoint 12.4. Doubling the diameter quadruples the cross-sectional area, \(A = \pi d^2/4\). With the same load, the stress \(F/A\) falls to \(\tfrac{1}{4}\); the strain, which is stress divided by \(Y\), also falls to \(\tfrac{1}{4}\); the elongation, which is strain times the same length, falls to \(\tfrac{1}{4}\); and the effective spring constant \(k = YA/L\) increases by a factor of \(4\). None of the four is a property of the material alone: each depends on the load or on the wire’s dimensions. The material property is Young’s modulus \(Y\), which is the same for both wires.

    Checkpoint 12.5. Loading follows the straight elastic line up to the elastic limit, then bends over as the wire yields. On unloading, the stress falls along a straight line parallel to the original elastic line, reaching zero stress at a positive strain. So yes, the wire is permanently longer than it started. On reloading, it follows that same parallel line back up and behaves elastically until the stress reaches the highest value it saw before, which is above the original yield strength. The wire has become harder to deform permanently. Cold-working a metal (rolling, drawing, hammering) does exactly this: each plastic deformation raises the stress needed to cause the next one.


    This page titled 12.3: Elasticity was last modified on Thu, 12 Nov 2026 04:26:48 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.