12.2: Center of Gravity and Stability

Physics: A Foundation for Scientists and Engineers · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    12.2: Center of Gravity and Stability

    Throughout the last section we treated each object’s weight as though it acted at a single point. That point is the center of gravity (cg): the point where the total gravitational force can be considered to act. Its position is the weight-weighted average of the positions of all the parts:

    \[x_{\rm cg} = \frac{\sum m_i g\, x_i}{\sum m_i g}. \tag{12.2}\]

    As long as \(g\) is the same everywhere on the object (true for any everyday object), the \(g\)’s cancel and the center of gravity coincides exactly with the center of mass of §9.5. This is why we can replace an extended body’s distributed weight with a single force \(mg\) at its center of mass when computing torques. For a uniform, symmetric object the cg sits at the geometric center; for a composite object it is found by treating each part’s weight as acting at that part’s own center.

    Example 12.5: A father-daughter seesaw

    A seesaw is a uniform board of mass \(M\) and length \(L\), pivoted at its center (its center of gravity). A father of mass \(m_f\) sits a distance \(d\) from the center. His daughter, of mass \(m_d\), sits on the opposite side, at the very end of the board: a distance \(L/2\) from the center. (a) Where must the father sit for balance? (b) What upward force does the pivot supply?

    A seesaw board of length L balanced on a pivot at its center.Figure descriptionA seesaw board of length L balanced on a pivot at its center. The father's weight m sub f g acts downward a distance d to the left of the pivot; the daughter's weight m sub d g acts downward at the right end, a distance L over 2 from the pivot. The board's own weight M g acts at the pivot, and the pivot pushes up with force F sub N.
    Solution

    (a) Because the board is pivoted at its own center of gravity, the board’s weight produces no torque about the pivot (its lever arm is zero). Balancing the father’s and daughter’s torques:

    \[m_f\,g\,d = m_d\,g\,\frac{L}{2}.\]

    Divide both sides by \(m_f g\); the \(g\) cancels:

    \[d = \boxed{\frac{m_d L}{2 m_f}}.\]

    A heavier father sits closer to the pivot, as experience confirms. The units check: masses divide out, leaving a length. And if the two masses were equal, \(d = L/2\): the father would sit at the other end, as symmetry demands.

    (b) The pivot must support the entire weight, since the net vertical force is zero: \(F_N - Mg - m_f g - m_d g = 0\), so

    \[F_N = \boxed{(M + m_f + m_d)\,g}.\]

    Note that this does not depend on where anyone sits: moving the riders around redistributes torque, not weight.

    Stability and the base of support

    Knowing where the center of gravity sits does more than let us compute torques: it tells us whether an object will stay put at all. An object resting on a surface touches it over some region, and the base of support is the smallest area enclosing all of those contact points. For a filing cabinet it is the rectangle under the cabinet; for a person standing it is the region spanned by both feet; for a tripod it is the triangle joining the three feet.

    Two panels on tipping: a block stable when the vertical through its center falls inside the base.
    Figure 12.1. Tipping. The dashed line is the vertical through the center of gravity. In (a) it lands inside the base of support and the block stands. In (b) the block has been tilted just far enough that the line passes through the contact edge: the critical angle. In (c) the line has fallen outside the base, and gravity’s torque about the edge rotates the block over. Tilting the block is equivalent to placing it on a ramp of the same angle.
    Figure descriptionTwo panels on tipping. In panel (a) the dashed vertical line through the center of gravity falls inside the base of support and the block is stable. In panel (b) the block is tilted further, the line falls outside the base, and the block topples.

    Now picture the vertical line running downward through the center of gravity. The weight acts along that line, and the supporting normal forces act somewhere within the base. So long as the line falls inside the base, the support can distribute itself to balance the weight with no leftover torque, and the object stands. Tilt the object far enough that the line passes outside the base, and it cannot: the contact has shifted to a single edge, and gravity’s torque about that edge is unopposed. The object tips (Figure 12.1).

    For a uniform rectangular block of width \(w\) and height \(h\) standing on a surface that is slowly tilted, the center of gravity is a horizontal distance \(w/2\) from the downhill edge and a height \(h/2\) above the base. The vertical through it reaches that edge when

    Key Equation: Critical tipping angle for a block

    \[\tan\theta_{\rm c} = \frac{w}{h}. \tag{12.3}\]

    Wide and low means a large \(\theta_{\rm c}\) and a stable object; tall and narrow means a small one. This single result explains a great deal of practical design: why sports cars are built low and wide, why a loaded moving truck is far more prone to rollover than an empty one (loading raises \(h\)), why a stepladder splays its feet outward, and why you widen your stance on a moving bus.

    It is also worth naming the three ways an object can sit in equilibrium. If a small displacement raises the center of gravity, gravity pushes the object back and the equilibrium is stable: a marble in a bowl, or the block of Figure 12.1(a). If the displacement lowers it, the object keeps going and the equilibrium is unstable: a pencil balanced on its tip, or the block in (c). If the height is unchanged, the equilibrium is neutral: a ball on a level table is content anywhere. Case (b), exactly at the critical angle, is the unstable boundary between the first two.

    Example 12.6: Will the crate slide or tip?

    A uniform crate \(0.80\,\mathrm{m}\) wide and \(1.6\,\mathrm{m}\) tall sits on a ramp whose angle is slowly increased from zero. The coefficient of static friction between crate and ramp is \(\mu_s = 0.60\). Which happens first, sliding or tipping, and at what angle?

    Solution

    Treat the two failures separately and see which one the ramp angle reaches first.

    Sliding. On an incline the crate begins to slide when the component of gravity along the ramp overcomes maximum static friction, which (from Chapter 6) happens at

    \[\tan\theta_{\rm slide} = \mu_s = 0.60 \;\Longrightarrow\; \theta_{\rm slide} = \arctan 0.60 = 31.0^\circ.\]

    Tipping. From equation (12.3), the vertical through the center of gravity leaves the base at

    \[\tan\theta_{\rm c} = \frac{w}{h} = \frac{0.80\,\mathrm{m}}{1.6\,\mathrm{m}} = 0.50 \;\Longrightarrow\; \theta_{\rm c} = \arctan 0.50 = 26.6^\circ.\]

    Tipping happens at the smaller angle, so the crate \(\boxed{\text{tips first, at } 26.6^\circ}\): it never gets the chance to slide.

    A rule from the comparison. Between \(0^\circ\) and \(90^\circ\) the tangent always increases with the angle, so comparing two angles is the same as comparing their tangents. The crate tips first exactly when \(\tan\theta_{\rm c} < \tan\theta_{\rm slide}\), that is, whenever \(w/h < \mu_s\). There was no need to compute either angle to answer “which first”: \(0.50 < 0.60\) settles it. Tall, narrow objects on grippy surfaces tip; short, wide objects on slippery ones slide.

    Checkpoint 12.3

    A hiker puts on a heavy backpack and immediately leans forward; a waiter carrying a loaded tray on one side leans away from it. Neither is thinking about physics. Using the base of support, explain what both are actually accomplishing, and explain why a person carrying a heavy suitcase in one hand cannot simply stand up straight.

    Answer

    Answers to Checkpoints

    Checkpoint 12.3. Both are keeping the combined center of gravity (their body plus the load) directly above the base of support, their feet. The backpack moves the combined center of gravity backward, so the hiker leans forward to bring it back over the feet; the waiter leans away from the tray for the same reason. A person holding a heavy suitcase in one hand who stood perfectly straight would have the combined center of gravity shifted toward the suitcase, near or beyond the edge of the feet. Gravity would then exert a torque about that edge and tip the person toward the suitcase, so the person must lean the other way.


    This page titled 12.2: Center of Gravity and Stability was last modified on Thu, 12 Nov 2026 04:26:48 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.