24.2: Faraday’s Law of Induction

Physics: A Foundation for Scientists and Engineers · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    24.2: Faraday’s Law of Induction
    Faraday's experiment in three panels, one above another.
    Figure 24.3. Faraday’s experiment. (a) Moving a magnet toward a coil induces a current, shown by the galvanometer (G). (b) While the magnet is held still, the flux through the coil does not change and no current flows. (c) Moving the magnet away reverses the current.
    Figure descriptionFaraday's experiment in three panels, one above another. In each, a bar magnet with its north pole facing right sits to the left of a coil of wire whose axis is horizontal, and the two ends of the coil are wired to a galvanometer, a meter drawn as a circle with a needle and a zero mark at the top. Panel a: the magnet moves to the right, toward the coil, with velocity v, and the needle swings to the right. Panel b: the magnet is at rest, and the needle points straight up at zero. Panel c: the magnet moves to the left, away from the coil, and the needle swings to the left.

    Faraday’s experiments, and many like them, can all be summarized in one statement. Push a bar magnet into a coil connected to a galvanometer, and a current flows while the magnet moves (Figure 24.3). Hold the magnet still, and the current stops. Pull it out, and the current flows the other way. Move the coil instead of the magnet, and the result is the same. Replace the magnet with a second coil, and switch its current on or off, and again a current flows in the first coil, but only while the current in the second is changing. In every case, a current is induced whenever the magnetic flux through the circuit changes, and the faster it changes, the larger the current. This is electromagnetic induction.

    What is induced, more fundamentally, is an emf, which drives the current through the circuit’s resistance. Faraday’s law of induction states that the induced emf in a circuit equals the negative of the rate of change of the magnetic flux through it:

    Key Equation: Faraday’s law

    \[\mathcal{E} = -\frac{d\Phi_B}{dt} \qquad{\text{(for a coil of }N\text{ turns, }} \mathcal{E} = -N\frac{d\Phi_B}{dt}\text{)}. \tag{24.3}\]

    For a tightly wound coil, the same flux passes through each of the \(N\) turns, and their emfs add, like batteries in series. The minus sign comes from Lenz’s law: the induced emf always acts to oppose the change in flux that produces it. Section 24.2 explains what that means for the direction of the emf. The emf is in volts, since \(1\,\mathrm{Wb/s} = 1\,\mathrm{T\cdot m^2/s} = 1\,\mathrm{V}\). If the circuit has resistance \(R\), the induced current is \(I = |\mathcal{E}|/R\).

    Since \(\Phi_B = BA\cos\theta\) for a flat loop in a uniform field, there are three ways to induce an emf: change the field \(B\); change the area \(A\) of the loop inside the field; or change the angle \(\theta\) by turning the loop. The first is how transformers work (Chapter 25), the second is the motional emf of Section 24.3, and the third is how generators work (Section 24.4).

    Example 24.3: A coil in a changing field

    A coil of 200 turns, each of area \(4.0\times 10^{-3}\,\mathrm{m^2}\), has its plane perpendicular to a uniform magnetic field. The field increases steadily from \(0.10\,\mathrm{T}\) to \(0.50\,\mathrm{T}\) in \(0.20\,\mathrm{s}\). (a) Find the magnitude of the induced emf. (b) If the coil has a resistance of \(8.0\,\mathrm{\Omega}\), what current flows, and how much charge passes through it?

    Solution

    (a) The flux through each turn changes by \(\Delta\Phi_B = A\,\Delta B = (4.0\times10^{-3})(0.40) = 1.6\times 10^{-3}\,\mathrm{Wb}\), at a steady rate. So

    \[|\mathcal{E}| = N\frac{\Delta\Phi_B}{\Delta t} = (200)\,\frac{1.6\times10^{-3}\,\mathrm{Wb}}{0.20\,\mathrm{s}} = \boxed{1.6\,\mathrm{V}}.\]

    (b) \(I = |\mathcal{E}|/R = 1.6/8.0 = \boxed{0.20\,\mathrm{A}}\), flowing for \(0.20\,\mathrm{s}\), so \(Q = I\,\Delta t = \boxed{0.040\,\mathrm{C}}\). Notice that \(Q = N\,\Delta\Phi_B/R\) does not depend on how fast the field changed: a faster change gives a larger current for a shorter time. Faraday measured flux this way, from the charge that passed through a galvanometer.

    End-on view of a solenoid of radius R whose field into the page is increasing.
    Figure 24.4. A magnetic field that is changing inside a solenoid induces an electric field whose field lines are closed circles, both inside and outside. For a field into the page that is increasing, the induced field circulates counterclockwise.
    Figure descriptionThe cross-section of a long solenoid, a circle of radius R, seen end-on, with its magnetic field into the page, shown by crosses in circles, increasing with time. Circular induced electric field lines, centered on the axis, circulate counterclockwise both inside and outside the solenoid. A dashed circle of radius r inside the solenoid is marked, with E tangent to it.

    The induced electric field. What pushes the charges around the circuit? The circuit need not move, so it is not a magnetic force. It must be an electric field, and Faraday’s law says where it comes from: a changing magnetic flux produces an electric field. The emf around a closed loop is the work per unit charge done by this field, \(\oint\vec{E}\cdot d\vec{s}\), so Faraday’s law can be written in terms of the fields alone:

    \[\oint\vec{E}\cdot d\vec{s} = -\frac{d\Phi_B}{dt}. \tag{24.4}\]

    The loop need not be a wire. This induced electric field exists in empty space wherever the magnetic field changes, whether or not there is a conductor to carry a current. It is quite unlike the electric field of static charges. Its field lines do not begin and end on charges; they form closed loops around the changing magnetic field (Figure 24.4). And its line integral around a closed path is not zero, so it is not conservative: it cannot be described by an electric potential, and Kirchhoff’s loop rule does not hold for a path around a changing flux (Section 21.2). Equation (24.4) is one of Maxwell’s four equations (Chapter 27).

    Example 24.4: Stimulating the brain

    In transcranial magnetic stimulation (TMS), a coil held against the head produces a brief pulse of magnetic field. Inside the head, the field is roughly uniform over a region of radius about \(2\,\mathrm{cm}\) and rises at a rate of about \(1.0\times 10^{4}\,\mathrm{T/s}\). Estimate the induced electric field \(1.0\,\mathrm{cm}\) from the axis of the field region.

    Solution

    By symmetry, the induced field lines are circles about the axis, and \(E\) is the same all around a circle of radius \(r\). Apply equation (24.4) to such a circle, inside the field region, where the flux it encloses is \(\pi r^2B\):

    \[E(2\pi r) = \pi r^2\frac{dB}{dt} \qquad\Longrightarrow\qquad E = \frac{r}{2}\frac{dB}{dt} = \frac{0.010\,\mathrm{m}}{2}\,(1.0\times10^{4}\,\mathrm{T/s}) = \boxed{50\,\mathrm{V/m}}.\]

    (We have dropped the minus sign, which only sets the direction.) A field of this size in the brain tissue drives currents strong enough to trigger nerve impulses, without any electrodes touching the patient. TMS is used to map brain function and to treat depression.

    Note: Induction at work

    An electric guitar’s pickup is a small coil wound around a magnet. The magnet magnetizes the steel string above it, and as the string vibrates, the flux through the coil oscillates at the string’s frequency, inducing an emf that is amplified to make the sound. A ground-fault circuit interrupter, the outlet with test and reset buttons in bathrooms and kitchens, surrounds both wires of the circuit with a small coil. Normally the currents in the two wires are equal and opposite and their fields cancel; if some current leaks to ground, perhaps through a person, the imbalance produces a changing flux, the induced emf trips a switch, and the power is cut in milliseconds. Induction cooktops, wireless phone chargers, and the readers for transit cards all work by induction too.

    Lenz’s Law

    The minus sign in Faraday’s law gives the direction of the induced emf, but it is usually easier to find the direction with a rule stated by Heinrich Lenz in 1834. Lenz’s law: the induced current flows in the direction that makes its own magnetic field oppose the change in flux that produced it.

    Four panels of a bar magnet moving near a wire loop, illustrating Lenz's law.
    Figure 24.5. Lenz’s law. In each case the induced current in the loop makes a field \(\vec{B}_{\text{ind}}\) that opposes the change in flux, so that the loop repels an approaching magnet and attracts a receding one. The arrow shows the current on the front side of the loop. The letters beside each loop give the poles of the loop’s own field: the loop acts like a small bar magnet, with the face nearest the magnet the same pole as the approaching end (so it repels) or the opposite pole of the receding end (so it attracts).
    Figure descriptionFour panels, each showing a bar magnet on the left and a circular wire loop on the right, seen in perspective with its axis horizontal. Panel a: the north pole faces the loop and moves toward it; the flux through the loop to the right increases, and the induced current creates a field pointing left, so the loop behaves like a small magnet whose face nearest the bar magnet is a north pole, marked N beside the loop, and it repels the magnet. Panel b: the north pole moves away; the flux decreases and the induced current creates a field to the right, so the loop's face nearest the magnet becomes a south pole, marked S, and attracts the magnet. Panel c: the south pole faces the loop and moves toward it; the induced field points right and the loop's near face becomes a south pole, repelling. Panel d: the south pole moves away; the induced field points left and the loop's near face becomes a north pole, attracting. In each panel an arrow on the front of the loop shows the direction of the induced current.

    Note that the induced current opposes the change in the flux, not the flux itself. Figure 24.5 shows four cases. When the north pole of a magnet approaches a loop (a), the flux through the loop, directed away from the magnet, increases. The induced current makes a field pointing back toward the magnet, to oppose the increase; the face of the loop toward the magnet acts as a north pole, and repels the magnet. When the north pole recedes (b), the flux decreases, and the induced current makes a field in the same direction as the magnet’s, to prop up the flux; now the near face of the loop acts as a south pole, and attracts the receding magnet. Reversing the magnet (c, d) reverses everything. Every time, the induced current pushes against the motion that caused it.

    Lenz’s law and energy. Lenz’s law is a consequence of energy conservation. Suppose the induced current flowed the other way, so that an approaching north pole met a south pole and was pulled in. The magnet would speed up, increasing the induced current, which would pull it in harder: it would gain kinetic energy while the current delivered energy to the circuit’s resistance, all for nothing. Because the induced current always opposes the motion, you must do work to move the magnet, and that work is exactly the electrical energy that appears in the circuit.

    Eddy currents. Induced currents flow not only in wires but in any piece of metal where the flux is changing. These swirling eddy currents dissipate energy as heat, and by Lenz’s law they oppose the motion that produces them. A metal plate swinging into a strong magnetic field stops abruptly, as if it had entered thick syrup. This magnetic braking is used to stop roller coasters and high-speed trains smoothly, with no contact and no wear. Eddy currents are also what heat the pan on an induction cooktop. Where they are unwanted, as in the iron cores of transformers and motors, the cores are made of thin insulated sheets, which cut the eddy currents’ paths.

    Example 24.5: A magnet dropped through a copper pipe

    A strong magnet dropped down a vertical copper pipe falls far more slowly than a stone dropped beside it, even though copper is not attracted to magnets. Explain.

    Solution

    As the magnet falls, the flux through each ring of the pipe below it increases, and the flux through each ring above it decreases. By Lenz’s law, the rings below carry eddy currents that repel the approaching magnet, and the rings above carry currents that attract the departing magnet, pulling it back. Both forces point up. The faster the magnet falls, the faster the flux changes, and the larger the currents and the upward force. The magnet quickly reaches a terminal speed at which the magnetic drag balances its weight, much like an object falling through a fluid (Section 6.2). The magnet’s lost gravitational potential energy becomes heat in the pipe.

    Checkpoint 24.1

    A circular loop lies flat on a table. A magnet held above it, with its north pole down, is lifted straight up and away. (a) Does the flux through the loop increase or decrease? (b) Seen from above, does the induced current circulate clockwise or counterclockwise? (c) Is the magnet attracted or repelled by the loop as it rises?

    Answer

    Answers to Checkpoints

    Checkpoint 24.1. (a) Near the north pole the field points downward through the loop, so the downward flux decreases as the magnet moves away. (b) By Lenz’s law the induced current opposes the change, so it tries to keep the downward flux from falling: it produces its own downward field inside the loop. Seen from above, a current making a downward field circulates clockwise. (c) Attracted. The loop now acts like a magnet whose south pole faces up, toward the magnet’s north pole, so it pulls back on the rising magnet: opposing the motion that causes the change, as Lenz’s law requires.


    This page titled 24.2: Faraday’s Law of Induction was last modified on Thu, 12 Nov 2026 04:27:07 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.