24.3: Motional EMF

Physics: A Foundation for Scientists and Engineers · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    24.3: Motional EMF
    A conducting rod of length L lies across two long horizontal parallel rails.
    Figure 24.6. A rod sliding on rails in a magnetic field into the page. The motional emf \(BLv\) drives a counterclockwise current. The magnetic force on the current in the rod opposes its motion, so an applied force is needed to keep it moving.
    Figure descriptionA conducting rod of length L lies across two long horizontal parallel rails. The rails are joined on the left by a resistor R. The whole arrangement lies in a uniform magnetic field pointing into the page, shown by crosses in circles. The rod moves to the right with velocity v, pulled by an applied force. The induced current I flows up through the rod, left along the top rail, down through the resistor, and right along the bottom rail: counterclockwise. The magnetic force on the current in the rod, I L cross B, points to the left, opposing the motion.

    An emf is also induced when a conductor moves through a magnetic field. Consider a conducting rod of length \(L\) sliding with speed \(v\) along two parallel conducting rails that are joined at one end by a resistor \(R\), in a uniform field \(\vec{B}\) perpendicular to the plane of the rails (Figure 24.6).

    From the magnetic force. The free charges in the rod move with it, with velocity \(\vec{v}\), so each feels a magnetic force \(q\vec{v}\times\vec{B}\), directed along the rod. For positive carriers, with \(\vec{B}\) into the page and \(\vec{v}\) to the right, the force points up the rod. The charges are pushed along the rod, doing work \(qvB\) per unit charge per unit length, or \(qvBL\) along its whole length. The rod acts as a battery with emf

    Key Equation: Motional emf

    \[\mathcal{E} = BLv. \tag{24.5}\]

    This is motional emf. It requires \(\vec{B}\), \(\vec{v}\), and the rod all to be perpendicular to each other; if they are not, only the perpendicular components count.

    From Faraday’s law. The same result follows from Faraday’s law. The rod, the rails, and the resistor form a closed circuit. As the rod moves, the area inside the circuit grows: if the rod is a distance \(x\) from the resistor, the flux is \(\Phi_B = BLx\), and it changes at the rate \(d\Phi_B/dt = BL\,dx/dt = BLv\). So \(|\mathcal{E}| = BLv\), as before. Motional emf is Faraday’s law applied to a circuit whose area changes.

    Direction and energy. As the rod moves to the right, the flux into the page increases. By Lenz’s law, the induced current makes a field out of the page inside the circuit, so it circulates counterclockwise: up through the rod, as the magnetic force on positive carriers also says. The current \(I = BLv/R\) in the rod feels a magnetic force \(I\vec{L}\times\vec{B}\) (equation (22.8)), of magnitude

    \[F_B = ILB = \frac{B^2L^2v}{R},\]

    pointing to the left, against the motion. To keep the rod moving at constant speed, you must push it with an equal force, doing work at the rate

    \[P = F_{\text{app}}v = \frac{B^2L^2v^2}{R}.\]

    This is exactly the rate at which the resistor dissipates energy, \(I^2R = (BLv/R)^2R = B^2L^2v^2/R\). Your mechanical work becomes electrical energy, and then heat, just as Lenz’s law requires. The sliding rod is the simplest possible electric generator.

    Example 24.6: A sliding rod

    In Figure 24.6, \(B = 0.50\,\mathrm{T}\), \(L = 0.20\,\mathrm{m}\), and \(R = 0.40\,\mathrm{\Omega}\); the rod and rails have negligible resistance. The rod moves at \(4.0\,\mathrm{m/s}\). Find (a) the emf, (b) the current, (c) the force needed to keep the rod moving, and (d) the power delivered to the resistor.

    Solution

    (a) \(\mathcal{E} = BLv = (0.50)(0.20)(4.0) = \boxed{0.40\,\mathrm{V}}\).

    (b) \(I = \mathcal{E}/R = 0.40/0.40 = \boxed{1.0\,\mathrm{A}}\), counterclockwise.

    (c) \(F = ILB = (1.0)(0.20)(0.50) = \boxed{0.10\,\mathrm{N}}\), to the right, balancing the magnetic force.

    (d) \(P = I^2R = (1.0)^2(0.40) = \boxed{0.40\,\mathrm{W}}\). As a check, the applied force does work at the rate \(Fv = (0.10)(4.0) = 0.40\,\mathrm{W}\), the same.

    Example 24.7: A flying airplane

    An airliner with a wingspan of \(60\,\mathrm{m}\) flies horizontally at \(250\,\mathrm{m/s}\) where the vertical component of Earth’s field is \(40\,\mathrm{\mu T}\). Find the emf between its wingtips. Could it be used to power anything?

    Solution

    The wing is a conductor moving perpendicular to the vertical component of the field, so

    \[\mathcal{E} = BLv = (4.0\times10^{-5})(60)(250) = \boxed{0.60\,\mathrm{V}}.\]

    It cannot drive a current through a circuit on board. Any wire connected between the wingtips moves along with the wing, through the same field, and has the same emf induced in it, so the two emfs cancel around the loop. Only a circuit with part of it at rest in the field, like the rails in Figure 24.6, can deliver motional emf as a current. (Tethered satellites, trailing a conducting cable kilometers long through the ionosphere, have tested this idea in orbit, using the surrounding plasma to close the circuit.)

    Checkpoint 24.2

    In the sliding-rod circuit of Figure 24.6, the rod is pushed along the rails at twice its former speed. By what factor does each of these change: (a) the induced emf, (b) the current, (c) the magnetic force on the rod, and (d) the power you must supply to keep it moving at that speed?

    Answer

    Answers to Checkpoints

    Checkpoint 24.2. (a) The emf \(\mathcal{E} = BLv\) is proportional to the speed, so it doubles. (b) The circuit’s resistance is unchanged, so \(I = \mathcal{E}/R\) doubles too. (c) The force on the rod is \(ILB\), proportional to the current, so it doubles. (d) To keep the rod moving at constant speed you must push with a force equal to that magnetic force, and the power is force times speed. Both have doubled, so the power rises by a factor of \(4\), and all of it appears as heat, \(I^2R\), in the resistance.


    This page titled 24.3: Motional EMF was last modified on Thu, 12 Nov 2026 04:27:07 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.