24.1: Magnetic Flux

Physics: A Foundation for Scientists and Engineers · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    24.1: Magnetic Flux
    Tilted flat loop of area A in a uniform magnetic field B.
    Figure 24.1. The magnetic flux through a flat loop in a uniform field is \(\Phi_B = BA\cos\theta\), where \(\theta\) is the angle between \(\vec{B}\) and the normal \(\hat{n}\) to the loop.
    Figure descriptionA flat rectangular loop of area A, drawn in perspective and tilted, in a uniform magnetic field B represented by parallel arrows pointing up and to the right. A unit vector n-hat, normal to the loop, makes an angle theta with the direction of B. Only the component of B along n-hat, B cos theta, passes through the loop.

    Faraday found that the induced effects depend on how many magnetic field lines pass through a circuit, and on how fast that number changes. The quantity that measures this is the magnetic flux, defined exactly as the electric flux was in Chapter 17. For a flat surface of area \(A\) in a uniform magnetic field, let \(\hat{n}\) be a unit vector normal to the surface, and \(\theta\) the angle between \(\vec{B}\) and \(\hat{n}\) (Figure 24.1). The magnetic flux through the surface is

    \[\Phi_B = \vec{B}\cdot\vec{A} = BA\cos\theta, \tag{24.1}\]

    where \(\vec{A} = A\hat{n}\). It is largest when the field passes straight through the surface (\(\theta = 0\)), and zero when the field lies parallel to the surface (\(\theta = 90^\circ\)), so that no field lines cross it. If the field is not uniform or the surface is not flat, divide the surface into small elements \(d\vec{A}\) and add their contributions:

    Key Equation: Magnetic flux

    \[\Phi_B = \int\vec{B}\cdot d\vec{A}. \tag{24.2}\]

    The SI unit of magnetic flux is the weber (Wb), after the German physicist Wilhelm Weber: \(1\,\mathrm{Wb} = 1\,\mathrm{T\cdot m^2}\). For a surface that is not closed, the direction of \(\hat{n}\) is a choice, and it sets the sign of the flux. For a surface bounded by a circuit, we will tie it to the direction around the circuit by the right-hand rule. For a closed surface, the flux is always zero, by Gauss’s law for magnetism (Section 23.6).

    Example 24.1: Flux through a loop in Earth’s field

    A horizontal circular loop of radius \(20\,\mathrm{cm}\) lies on a table where Earth’s field is \(50\,\mathrm{\mu T}\), pointing down into the ground at \(60^\circ\) below the horizontal. Find the flux through the loop.

    Solution

    Take \(\hat{n}\) pointing straight down. The field makes an angle of \(90^\circ - 60^\circ = 30^\circ\) with the vertical, so

    \[\Phi_B = BA\cos\theta = (5.0\times10^{-5}\,\mathrm{T})\,\pi(0.20\,\mathrm{m})^2\cos 30^\circ = \boxed{5.4\times 10^{-6}\,\mathrm{Wb}}.\]

    Only the vertical component of Earth’s field contributes: the horizontal component lies in the plane of the loop.

    Long wire carrying current I with a rectangular loop beside it in the same plane.
    Figure 24.2. Finding the flux of a long wire’s field through a rectangular loop. The field is uniform along each thin strip parallel to the wire, so the flux is found by adding the strips.
    Figure descriptionA long vertical straight wire carrying current I upward, and to its right, in the same plane, a rectangular loop with its long sides of length a parallel to the wire. The near side of the loop is a distance d from the wire and the loop has width b. A thin vertical strip of the loop, of width d r, is shaded at a distance r from the wire. The wire's magnetic field points into the page over the loop, shown by crosses in circles.
    Example 24.2: Flux beside a long wire

    A long straight wire carries \(20\,\mathrm{A}\). A rectangular loop of length \(a = 10\,\mathrm{cm}\) (parallel to the wire) and width \(b = 4.0\,\mathrm{cm}\) lies in the same plane, with its near side \(d = 1.0\,\mathrm{cm}\) from the wire (Figure 24.2). Find the flux through the loop.

    Solution

    The field of the wire, \(\mu_0 I/2\pi r\), is perpendicular to the plane of the loop but not uniform: it weakens with distance \(r\) from the wire. Divide the loop into thin strips of width \(dr\) and length \(a\), parallel to the wire. The field is uniform across each strip, so its flux is \(d\Phi_B = B\,a\,dr\), and

    \[\begin{aligned}\Phi_B &= \int_d^{d+b}\frac{\mu_0 I}{2\pi r}\,a\,dr = \frac{\mu_0 Ia}{2\pi}\ln\frac{d + b}{d} \\ &= (2\times10^{-7})(20)(0.10)\ln 5.0 = \boxed{6.4\times 10^{-7}\,\mathrm{Wb}}.\end{aligned}\]


    This page titled 24.1: Magnetic Flux was last modified on Thu, 12 Nov 2026 04:27:06 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.