33.3: Interference from Thin Films

Physics: A Foundation for Scientists and Engineers · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    33.3: Interference from Thin Films

    The shimmer of color on a soap bubble or an oil slick is interference at work, with no slits at all. Light reflecting off the top of a thin transparent film interferes with light that enters, reflects off the bottom, and comes back out. Whether a given color reinforces or cancels depends on the film’s thickness, so different thicknesses flash different colors.

    Three things can shift the relative phase of two waves: traveling different path lengths, traveling through different media (where the wavelength shrinks to \(\lambda/n\)), and reflection itself. The third is easy to forget and crucial here: when light reflects from a medium of higher index of refraction, it flips phase by \(180^{\circ}\) (a jump of half a wavelength) just as a wave pulse on a rope inverts when it hits a fixed end. Reflecting from a lower-index medium causes no such flip.

    Thin film of index n and thickness t in air, with the two reflected rays that interfere.
    Figure 33.5. Interference in a thin film. Ray 1 reflects off the top surface, going from low to high index, and flips phase by \(180^{\circ}\) (filled dot). Ray 2 travels an extra path \(2t\) inside the film and reflects off the bottom surface, going from high to low index, with no flip (open dot). The single flip is equivalent to an extra half-wavelength.
    Figure descriptionA thin film of index n and thickness t, drawn as three layers: air on top, the film in the middle, and air again below. A red incident ray comes down from the upper left onto the top surface. Ray 1 reflects straight back up; a gold dot where it reflects is labeled 180 degree flip, air to film, low to high index. The rest of the light, drawn in green as ray 2, refracts into the film and travels down to the bottom surface, where an open circle is labeled no flip, film to air, high to low index. Ray 2 reflects there, comes back up and out roughly parallel to ray 1, having traveled an extra distance of about 2 t inside the film. A thinner dashed ray continues on down into the lower air. The two emerging rays are what interfere.

    Consider a film of index \(n\) and thickness \(t\) in air (Figure 33.5). Ray 1 reflects off the top surface (air-to-film, low-to-high) and does flip. Ray 2 passes into the film, reflects off the bottom surface (film-to-air, high-to-low) and does not flip, then exits having traveled an extra geometric distance \(2t\) inside the film. Two effects therefore separate the rays: the half-wavelength from the single reflection flip, and the path \(2t\), which holds \(2nt/\lambda\) wavelengths because the wavelength inside the film is \(\lambda/n\). With exactly one flip, the conditions for the reflected light are

    Key Equation: Thin film, one reflection phase flip

    \begin{align}2nt &= \left(m+\tfrac{1}{2}\right)\lambda, & &\text{(constructive, bright reflection)} \tag{33.9} \\ 2nt &= m\lambda, & &\text{(destructive, dark reflection)} \tag{33.10}\end{align}

    with \(m = 0, 1, 2, \dots\) and \(\lambda\) the wavelength in air.

    Example 33.4: A soap film at its thinnest

    A soap film (\(n = 1.33\)) in air is lit by light of free-space wavelength \(600\,\mathrm{nm}\). Find the minimum nonzero thickness that makes the reflected light interfere constructively (so the film looks bright at that color).

    Solution

    A soap film is air on both sides, so there is exactly one reflection flip (at the top). Constructive reflection therefore obeys equation (33.9), \(2nt = (m+\tfrac12)\lambda\). The thinnest film takes \(m=0\):

    \[t = \frac{\lambda}{4n} = \frac{600\,\mathrm{nm}}{4(1.33)} = \boxed{113\,\mathrm{nm}}.\]

    A bubble’s wall thins continuously as it drains under gravity; as \(t\) sweeps through the values that satisfy this condition for each color in turn, the wall flashes through the spectrum, and just before it pops, where \(t \to 0\) and \(2nt \to 0\) (the \(m=0\) destructive case), it goes black.

    Example 33.5: An anti-reflection coating

    A silicon solar cell (\(n = 3.5\)) is coated with a thin film of silicon dioxide (\(n = 1.45\)) to cut reflective losses. Find the minimum film thickness that gives the least reflection at \(\lambda = 550\,\mathrm{nm}\).

    Solution

    Here the geometry is different: light goes air (\(n=1\)) \(\to\) film (\(n=1.45\)) \(\to\) silicon (\(n=3.5\)). Both reflections are now low-to-high, so both rays flip by \(180^{\circ}\), as the sketch shows. Compare Figure 33.5, where the bottom reflection is high-to-low and does not flip.

    Anti-reflection coating of index 1.45 and thickness t on silicon of index 3.5.Figure descriptionAn anti-reflection coating, drawn as three layers: air on top, a thin coating of index 1.45 and thickness t in the middle, and silicon of index 3.5 at the bottom. An incident ray comes down from the upper left. Ray 1 reflects off the top of the coating; a gold dot there is labeled flip 1, 180 degrees, air to coating, low to high. Ray 2, in green, refracts into the coating, reflects off the silicon, where a second gold dot is labeled flip 2, 180 degrees, coating to silicon, low to high, and comes back out parallel to ray 1. A thinner dashed ray continues on into the silicon. Because both reflections flip, the flips cancel and only the extra path 2 n t inside the coating separates the two rays.

    Two flips cancel (there is no net reflection phase shift) so the conditions are the reverse of the single-flip case: least reflection (destructive) now requires a half-integer path,

    \[2nt = \left(m+\tfrac{1}{2}\right)\lambda.\]

    The minimum thickness is again \(m=0\):

    \[t = \frac{\lambda}{4n} = \frac{550\,\mathrm{nm}}{4(1.45)} = \boxed{94.8\,\mathrm{nm}}.\]

    A coating one quarter-wavelength thick (measured inside the film) makes the two reflected rays cancel, so almost no light bounces back and more passes into the cell. The same quarter-wave trick coats camera lenses and eyeglasses: the faint purple sheen you see on good optics.

    The two examples carry a warning worth stating plainly: the boxed conditions, Equations (33.9)–(33.10), assume one reflection flip. Always count the flips first: at each surface, ask whether the light is going from lower to higher index (a flip) or from higher to lower (no flip). An odd number of low-to-high reflections gives a net half-wave shift and the conditions above; an even number (zero or two) gives no net shift, and constructive and destructive swap places.

    Checkpoint 33.2

    (a) A vertical soap film in air drains and thins toward the top. Just before it pops, the thinnest region looks black by reflected light. Why black rather than bright? (b) An antireflection coating on a lens has a refractive index between those of air and glass. How many reflection phase flips occur, and which condition (equation (33.9) or (33.10)) now gives the dark reflection?

    Answer

    Answers to Checkpoints

    Checkpoint 33.2. (a) As the film’s thickness \(t\) approaches zero, the path difference \(2nt\) approaches zero too. For a soap film in air there is exactly one phase flip, at the front (air-to-soap) surface, so with zero path difference the two reflected waves are exactly out of step and cancel. The thinnest part reflects no light and looks black. (b) Two. The light flips on reflecting from the air–coating surface and again from the coating–glass surface, since each goes from lower to higher index. The two flips cancel, so the conditions swap: the dark reflection now occurs when \(2nt = (m + \tfrac{1}{2})\lambda\), the form of equation (33.9). The thinnest such coating is a quarter-wavelength thick.


    This page titled 33.3: Interference from Thin Films was last modified on Thu, 12 Nov 2026 04:27:08 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.