Opening the book…
Equation (18.1) finds the potential from the field by integrating. The process can be run in reverse. For a small step \(d\vec{s}\), the change in potential is \(dV = -\vec{E}\cdot d\vec{s} = -E_s\,ds\), where \(E_s\) is the component of the field along the step. Dividing by \(ds\),
\[E_s = -\frac{dV}{ds}.\]
The component of the field in any direction is the negative of the rate at which the potential changes in that direction. Taking the steps along the three coordinate axes gives the components of the field:
Key Equation: Field from potential
\[E_x = -\frac{\partial V}{\partial x}, \qquad E_y = -\frac{\partial V}{\partial y}, \qquad E_z = -\frac{\partial V}{\partial z}. \tag{18.16}\]
The partial derivative \(\partial V/\partial x\) means the ordinary derivative of \(V\) with respect to \(x\), treating \(y\) and \(z\) as constants. In vector notation the three equations are written \(\vec{E} = -\nabla V\), where \(\nabla V\), the gradient of \(V\), is the vector that points in the direction in which \(V\) increases fastest, with a magnitude equal to that rate of increase. The field therefore points in the direction in which the potential decreases fastest, perpendicular to the equipotentials, as Section 18.2 found.
This gives a two-step strategy that is often the easiest way to find a field: first find the scalar potential by an integral that needs no components, then differentiate it. Every field computed in Chapters 15 and 16 can be checked this way.
- Point charge: \(E_r = -\mathrm{d}(k_eq/r)/\mathrm{d}r = k_eq/r^2\).
- Ring: differentiating \(V = k_eQ(x^2 + a^2)^{-1/2}\) gives \(E_x = k_eQx/(x^2 + a^2)^{3/2}\), which is equation (16.11).
- Disk: differentiating equation (18.13) gives \(E_x = (\sigma/2\epsilon_0)\bigl(1 - x/\sqrt{x^2 + R^2}\bigr)\), which is equation (16.12).
- Dipole, on its axis: with \(\theta = 0\), \(V = k_ep/r^2\) and \(E_r = -\mathrm{d}V/\mathrm{d}r = 2k_ep/r^3\), which is equation (16.7).
Example 18.11: The field from a potential in two dimensions
In a certain region, the potential is \(V(x,y) = C(3x^2y - y^3)\), with \(C = 200\,\mathrm{V/m^3}\) and \(x\) and \(y\) in meters. Find the electric field at the point \((1.0\,\mathrm{m},\,2.0\,\mathrm{m})\).
Solution
Differentiate, holding the other variable constant:
\[E_x = -\frac{\partial V}{\partial x} = -6Cxy, \qquad E_y = -\frac{\partial V}{\partial y} = -C(3x^2 - 3y^2).\]
At \((1.0,\,2.0)\),
\[E_x = -6(200)(1.0)(2.0) = -2400\,\mathrm{V/m}, \qquad E_y = -200(3 - 12) = +1800\,\mathrm{V/m},\]
so \(\vec{E} = \boxed{(-2.4\,\hat{\imath} + 1.8\,\hat{\jmath})\times10^{3}\,\mathrm{V/m}}\), with magnitude \(\boxed{3.0\times 10^{3}\,\mathrm{V/m}}\).
Example 18.12: Reading the field from a graph of potential
The graph shows the potential along the \(x\)-axis in a certain region. Find \(E_x\) in each of the three regions.
Solution
In each region the graph is a straight line, so \(E_x = -\Delta V/\Delta x\) is constant.
- From \(0\) to \(2\,\mathrm{cm}\): \(E_x = -(60 - 0)/(0.020) = \boxed{-3.0\times 10^{3}\,\mathrm{V/m}}\). The field points in the \(-x\) direction, back toward lower potential.
- From \(2\) to \(5\,\mathrm{cm}\): the potential is constant, so \(\boxed{E_x = 0}\).
- From \(5\) to \(8\,\mathrm{cm}\): \(E_x = -(-30 - 60)/(0.030) = \boxed{+3.0\times 10^{3}\,\mathrm{V/m}}\).
A steep slope means a strong field, and the field always points “downhill.” The flat region could be the inside of a conductor.
Checkpoint 18.6
(a) At a certain point the potential is zero. Must the field be zero there? Give an example. (b) In a certain region the field is zero. What can you say about the potential there?
Answers to Checkpoints
Checkpoint 18.6. (a) No. The field depends on how the potential changes from point to point, not on its value. The midpoint of an electric dipole is an example: the potentials of the two charges cancel there, so \(V = 0\), but their fields both point from \(+\) toward \(-\) and add, so \(E \neq 0\). (b) The potential is constant throughout that region, but not necessarily zero. The interior of a charged conductor is an example: \(E = 0\) inside, and the potential has the same nonzero value everywhere in it.
This page titled 18.5: Calculating the Field from the Potential was last modified on Thu, 12 Nov 2026 04:27:02 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.
The book could not be loaded just now.