37.3: Thermodynamic Processes

Physics: A Foundation for Scientists and Engineers · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    37.3: Thermodynamic Processes
    P-V diagram of four paths leaving one common starting point.
    Figure 37.4. Four processes from a common starting state on a \(P\)–\(V\) diagram: isobaric (constant \(P\)), isovolumetric (constant \(V\)), isothermal (\(PV\) constant), and adiabatic (\(Q = 0\), falling more steeply than the isotherm). The area under each path is the work done by the gas.
    Figure descriptionA pressure-versus-volume diagram with four paths leaving one common starting point at high pressure and low volume. The isobaric path runs horizontally to the right at constant pressure. The isovolumetric path runs straight down at constant volume. The isothermal path curves down and to the right along a hyperbola where the product P V stays constant. The adiabatic path leaves from the same point and curves down more steeply than the isothermal, falling below it. The area beneath each path is the work the gas does.

    A change of state is a thermodynamic process, and four special cases are worth naming because in each one a different quantity is held fixed (Figure 37.4). For each, the first law tells us how the energy is shared between heat, work, and internal energy.

    • Isobaric: constant pressure. The area under the horizontal path is a rectangle, so \(W_{\rm by} = P\,\Delta V\).
    • Isovolumetric (isochoric): constant volume. No volume change means no work at all, so \(\Delta E_{\rm int} = Q\): all the heat goes into internal energy.
    • Isothermal: constant temperature. The process follows an isotherm, \(PV = \text{const}\). For an ideal gas, \(E_{\rm int}\) depends only on \(T\), so \(\Delta E_{\rm int} = 0\) and \(Q = W_{\rm by}\): every joule of heat absorbed leaves again as work.
    • Adiabatic: no heat transfer, \(Q = 0\). Then \(\Delta E_{\rm int} = W\); any change in internal energy comes entirely from work. A gas compressed adiabatically heats up, and a gas that expands adiabatically cools. Processes are nearly adiabatic when they are well insulated or simply too fast for much heat to flow, like the compression stroke of an engine or the expansion of air rising in the atmosphere.

    Isothermal work. Along an isotherm the pressure changes as the gas expands, \(P = nRT/V\), so we must integrate equation (37.5). With \(T\) constant,

    \[W_{\rm by} = \int_{V_i}^{V_f}\frac{nRT}{V}\,dV = nRT\int_{V_i}^{V_f}\frac{dV}{V},\]

    which gives

    Key Equation: Work in an isothermal process

    \[W_{\rm by} = nRT\ln\frac{V_f}{V_i}. \tag{37.6}\]

    The work is positive for an expansion (\(V_f > V_i\), so the logarithm is positive) and negative for a compression.

    Example 37.8: Boiling water: work, heat, and internal energy

    Let \(1.00\,\mathrm{kg}\) of water at \(100^{\circ}\mathrm{C}\) be boiled to steam at \(100^{\circ}\mathrm{C}\) at standard atmospheric pressure (\(1.01\times 10^{5}\,\mathrm{Pa}\)). The volume rises from \(1.00\times 10^{-3}\,\mathrm{m^3}\) (liquid) to \(1.671\,\mathrm{m^3}\) (steam). For water, \(L_v = 2.26\times 10^{6}\,\mathrm{J/kg}\).

    1. How much work does the system do during this process?
    2. How much energy is transferred as heat?
    3. What is the change in the system’s internal energy?
    Solution

    (a) The process is isobaric, so the work done by the expanding steam is

    \[W_{\rm by} = P\,\Delta V = (1.01\times10^5)(1.671 - 0.001) = (1.01\times10^5)(1.670) \approx \boxed{169\,\mathrm{kJ}}.\]

    (b) The heat is the latent heat of vaporization:

    \[Q = mL_v = (1.00)(2.26\times10^6) = 2.26\times 10^{6}\,\mathrm{J} = \boxed{2260\,\mathrm{kJ}}.\]

    (c) By the first law, with the work done on the system being \(W = -W_{\rm by} = -169\,\mathrm{kJ}\),

    \[\Delta E_{\rm int} = Q + W = 2260 - 169 \approx \boxed{2090\,\mathrm{kJ}}.\]

    Of the \(2260\,\mathrm{kJ}\) poured in, about \(169\,\mathrm{kJ}\) went into pushing back the atmosphere as the steam expanded, and the remaining \(2090\,\mathrm{kJ}\) went into the internal energy of the vapor: mostly the energy of pulling the water molecules apart.

    Checkpoint 37.3

    An ideal gas starts in a given state and expands to twice its volume, either (a) at constant pressure or (b) at constant temperature. Sketch both paths on a \(P\)–\(V\) diagram. In which process does the gas do more work, and which requires more heat?

    Answer

    Molar Specific Heats of an Ideal Gas

    For a gas it is more natural to count moles than kilograms, so we define the molar specific heat \(C\) by \(Q = nC\,\Delta T\). Unlike a solid or liquid, though, a gas has no single specific heat, because the heat needed for a given \(\Delta T\) depends on the process. Two cases matter most.

    At constant volume the gas does no work, so all the heat goes into internal energy: \(Q = \Delta E_{\rm int}\). From the equipartition theorem, \(E_{\rm int} = \tfrac f2 nRT\) (Chapter 36), so \(\Delta E_{\rm int} = \tfrac f2 nR\,\Delta T\), and the molar specific heat at constant volume is

    \[C_V = \frac{f}{2}R = \begin{cases} \tfrac32 R = 12.5\,\mathrm{J/(mol\cdot K)} & \text{monatomic},\\[2pt] \tfrac52 R = 20.8\,\mathrm{J/(mol\cdot K)} & \text{diatomic}. \end{cases} \tag{37.7}\]

    Because the internal energy of an ideal gas depends only on its temperature, this gives a result we will use constantly:

    \[\Delta E_{\rm int} = nC_V\,\Delta T \qquad \text{for \emph{any} process of an ideal gas}. \tag{37.8}\]

    At constant pressure the gas expands as it warms, so the heat must also pay for the work it does. The first law gives \(Q = \Delta E_{\rm int} + W_{\rm by} = nC_V\,\Delta T + P\,\Delta V\). At constant pressure the ideal gas law gives \(P\,\Delta V = nR\,\Delta T\), so \(Q = n(C_V + R)\,\Delta T\), and the molar specific heat at constant pressure is

    \[C_P = C_V + R. \tag{37.9}\]

    Their ratio, \(\gamma = C_P/C_V\), is the adiabatic index: \(\tfrac53 \approx 1.67\) for a monatomic gas and \(\tfrac75 = 1.40\) for a diatomic one.

    Table 37.3. Measured molar specific heats of gases near room temperature, compared with the equipartition predictions: \(C_V = \tfrac32R = 12.5\) and \(\gamma = 1.67\) (monatomic), \(C_V = \tfrac52R = 20.8\) and \(\gamma = 1.40\) (diatomic). Units of \(C_V\) and \(C_P\) are \(\,\mathrm{J/(mol\cdot K)}\).
    GasType\(C_V\)\(C_P\)\(\gamma = C_P/C_V\)
    Helium (\(\mathrm{He}\))monatomic\(12.5\)\(20.8\)\(1.67\)
    Argon (\(\mathrm{Ar}\))monatomic\(12.5\)\(20.8\)\(1.67\)
    Nitrogen (\(\mathrm{N_2}\))diatomic\(20.8\)\(29.1\)\(1.40\)
    Oxygen (\(\mathrm{O_2}\))diatomic\(21.1\)\(29.4\)\(1.40\)
    Carbon dioxide (\(\mathrm{CO_2}\))triatomic\(28.5\)\(37.0\)\(1.30\)

    Table 37.3 shows how well this works. The monatomic gases match the prediction exactly, and nitrogen and oxygen agree to within about \(1\%\), confirming that their molecules rotate but, at room temperature, do not vibrate (the frozen-out vibration of Chapter 36). Every gas obeys \(C_P - C_V = R = 8.3\,\mathrm{J/(mol\cdot K)}\).

    Adiabatic processes. When \(Q = 0\), the first law says \(dE_{\rm int} = -P\,dV\), or \(nC_V\,dT = -P\,dV\). Differentiating \(PV = nRT\) gives \(P\,dV + V\,dP = nR\,dT\). Eliminating \(dT\) between these two equations and using \(R = C_P - C_V\) leads, after a few lines of algebra, to \(dP/P = -\gamma\,dV/V\), which integrates to

    Key Equation: Adiabatic process of an ideal gas

    \[PV^{\gamma} = \text{constant}, \qquad TV^{\gamma-1} = \text{constant}. \tag{37.10}\]

    (The second form follows from the first with \(P = nRT/V\).) Since \(\gamma > 1\), an adiabat falls more steeply than an isotherm on a \(P\)–\(V\) diagram, as Figure 37.4 shows: as the gas expands, its pressure drops both because the volume grows and because the gas cools. The work done by the gas in an adiabatic process comes entirely out of its internal energy, \(W_{\rm by} = -\Delta E_{\rm int} = nC_V(T_i - T_f)\).

    Example 37.9: The diesel engine

    A diesel engine has no spark plugs. Air is drawn into the cylinder at \(20^{\circ}\mathrm{C}\) and \(1.01\times 10^{5}\,\mathrm{Pa}\) and compressed so rapidly that the process is essentially adiabatic, to \(1/18\) of its original volume. Fuel is then sprayed in. Find the temperature and pressure of the compressed air. Treat air as a diatomic ideal gas, \(\gamma = 1.40\).

    Solution

    From \(TV^{\gamma-1} = \text{const}\),

    \[T_f = T_i\left(\frac{V_i}{V_f}\right)^{\gamma-1} = (293\,\mathrm{K})(18)^{0.40} = (293)(3.18) = \boxed{932\,\mathrm{K}} \approx 659^{\circ}\mathrm{C}.\]

    From \(PV^\gamma = \text{const}\),

    \[P_f = P_i\left(\frac{V_i}{V_f}\right)^{\gamma} = (1.01\times10^5)(18)^{1.40} = (1.01\times10^5)(57.2) = \boxed{5.8\times 10^{6}\,\mathrm{Pa}},\]

    about \(57\) atmospheres. Diesel fuel ignites spontaneously at around \(250^{\circ}\mathrm{C}\), so the hot compressed air sets it burning the moment it is injected: compression alone does the job of the spark. (The pressure rises by a factor of \(57\) while the volume falls by only \(18\), because the gas also heats up.)

    Checkpoint 37.4

    Pumping up a bicycle tire quickly makes the barrel of the pump warm to the touch, even though no heat is supplied. Explain why, using the first law. Would the pump warm as much if you pumped very slowly?

    Answer

    Answers to Checkpoints

    Checkpoint 37.3. The work done by the gas is the area under its path on the \(P\)–\(V\) diagram. At constant pressure the path is a horizontal line from \(V\) to \(2V\); at constant temperature the pressure falls along an isotherm (\(P \propto 1/V\)) and ends at half its starting value. The isotherm lies below the horizontal line everywhere after the start, so the constant-pressure expansion encloses more area: the gas does more work, \(P_0V_0\) versus \(P_0V_0\ln 2 \approx 0.69\,P_0V_0\). It also needs more heat. In the isothermal case \(\Delta E_{\rm int} = 0\), so \(Q\) just equals the work. At constant pressure the temperature doubles (\(PV = nRT\)), so heat must supply both the larger work and an increase in internal energy.

    Checkpoint 37.4. Each quick stroke compresses the air in the pump faster than heat can leak out, so the compression is nearly adiabatic: \(Q \approx 0\) and \(\Delta E_{\rm int} = W > 0\). The work you do on the air raises its internal energy, and so its temperature, and the hot air warms the barrel. (Friction of the piston adds a little.) Pumped very slowly, the air would stay close to room temperature, because heat would have time to flow out through the barrel during each stroke; the compression would be nearly isothermal and the pump would barely warm.


    This page titled 37.3: Thermodynamic Processes was last modified on Thu, 12 Nov 2026 04:26:55 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.