21.3: Multiple Resistors in a Circuit: Series vs. Parallel

Physics: A Foundation for Scientists and Engineers · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    21.3: Multiple Resistors in a Circuit: Series vs. Parallel

    Kirchhoff’s laws handle any circuit, but many circuits contain groups of resistors that can be replaced by a single equivalent resistance, one that draws the same current from the same potential difference. Two arrangements are basic. The rules for them are much like those for capacitors in Section 19.4, but reversed.

    Two circuits: three resistors in series with a battery, and three in parallel.
    Figure 21.9. Resistors in combination. (a) In series, the same current passes through each resistor, and their potential differences add up to \(\mathcal{E}\). (b) In parallel, each resistor has the same potential difference across it, and their currents add up to the battery current, \(I = I_1 + I_2 + I_3\).
    Figure descriptionTwo circuit diagrams. In panel a, a battery of emf script E is connected to three resistors R sub 1, R sub 2 and R sub 3 one after another around a single loop, R sub 1 and R sub 2 in the top wire and R sub 3 on the right side, so the same current I passes through each. In panel b, the same battery is connected to three resistors arranged side by side between a top wire and a bottom wire, each spanning the same pair of wires, so each has the same potential difference V across it; junction dots mark where each resistor joins the wires, and the battery current I divides into I sub 1, I sub 2 and I sub 3.

    Resistors in series. Resistors connected one after another along a single path, with no junction between them, are in series (Figure 21.9a). There is only one path, so by the junction rule, the same current \(I\) passes through each. The loop rule says the potential differences across them add up to the battery’s emf:

    \[\mathcal{E} = IR_1 + IR_2 + IR_3 + \cdots = I(R_1 + R_2 + R_3 + \cdots).\]

    A single resistor that draws the same current from the same emf has

    Key Equation: Resistors in series

    \[R_{\text{eq}} = R_1 + R_2 + R_3 + \cdots. \tag{21.5}\]

    Resistances in series add, and the equivalent resistance is larger than any one of them. This is what we expect from \(R = \rho L/A\): resistors in series are like a single longer resistor.

    Resistors in parallel. Resistors connected side by side between the same two junctions are in parallel (Figure 21.9b). Each is connected directly across the same pair of wires, so each has the same potential difference \(V\), and each carries its own current, \(I_1 = V/R_1\), \(I_2 = V/R_2\), and so on. By the junction rule, the total current from the battery is the sum:

    \[I = I_1 + I_2 + I_3 + \cdots = V\left(\frac{1}{R_1} + \frac{1}{R_2} + \frac{1}{R_3} + \cdots\right).\]

    A single resistor that draws this total current at the same voltage has

    Key Equation: Resistors in parallel

    \[\frac{1}{R_{\text{eq}}} = \frac{1}{R_1} + \frac{1}{R_2} + \frac{1}{R_3} + \cdots. \tag{21.6}\]

    The equivalent resistance of resistors in parallel is always smaller than the smallest of them. Each new path in parallel gives the current another way through, like widening a pipe. For two resistors in parallel, equation (21.6) can be written \(R_{\text{eq}} = R_1R_2/(R_1 + R_2)\), “product over sum.” Two equal resistors in parallel have half the resistance of either. The largest current flows through the smallest resistance, since \(I = V/R\) for each.

    Note: Household wiring is in parallel

    The outlets and lights in a house are connected in parallel across the supply, so each device gets the full \(120\,\mathrm{V}\) (or \(230\,\mathrm{V}\) in much of the world), and each can be switched on or off without affecting the others. But every device added in parallel lowers the total resistance and raises the total current in the wires feeding the circuit. A circuit breaker or fuse, in series with the whole group, opens the circuit when that current exceeds a safe value, typically \(15\,\mathrm{A}\) or \(20\,\mathrm{A}\), before the wires in the walls overheat.

    Example 21.5: Bulbs in series and in parallel

    Two identical lamps, each with a resistance of \(240\,\mathrm{\Omega}\) when lit, are connected to a \(120\,\mathrm{V}\) supply. Find the power delivered to each lamp and the total power if they are connected (a) in parallel and (b) in series. Treat the resistance as constant.

    Solution

    (a) In parallel, each lamp has the full \(120\,\mathrm{V}\) across it, just as if it were alone, so each receives \(P = V^2/R = (120)^2/240 = \boxed{60\,\mathrm{W}}\), and the total is \(120\,\mathrm{W}\).

    (b) In series, \(R_{\text{eq}} = 480\,\mathrm{\Omega}\), and the current is \(I = 120/480 = 0.25\,\mathrm{A}\). Each lamp receives \(P = I^2R = (0.25)^2(240) = \boxed{15\,\mathrm{W}}\), and the total is only \(30\,\mathrm{W}\). Each lamp gets half the voltage and half the current, and so a quarter of the power. (In practice the cooler filaments have lower resistance, so the lamps glow a little more than this, but still dimly.) Old strings of holiday lights were wired in series, which is why one burned-out bulb darkened the whole string.

    Combinations. Many networks can be simplified step by step, replacing each group of resistors that is purely in series or purely in parallel by its equivalent, until only one resistor remains. Then the steps are retraced in reverse to find the current in, and voltage across, each original resistor.

    Three circuit diagrams in a row, showing a network being simplified.
    Figure 21.10. Simplifying the network of Example 21.6. (a) \(R_2\) and \(R_3\) are in parallel. (b) Their equivalent, \(2.0\,\mathrm{\Omega}\), is in series with \(R_1\). (c) The whole network is equivalent to \(6.0\,\mathrm{\Omega}\).
    Figure descriptionThree circuit diagrams in a row, showing a network being simplified. Panel a: a 12 volt battery on the left, a 4.0 ohm resistor R sub 1 in the top wire, and two resistors in parallel on the right, R sub 2 of 6.0 ohms and R sub 3 of 3.0 ohms, each connected between the top and bottom wires. Panel b: the parallel pair has been replaced by a single 2.0 ohm resistor, in series with the 4.0 ohm resistor. Panel c: the whole network has been replaced by a single 6.0 ohm resistor across the battery.
    Example 21.6: Simplifying a network

    In the circuit of Figure 21.10a, \(\mathcal{E} = 12\,\mathrm{V}\), \(R_1 = 4.0\,\mathrm{\Omega}\), \(R_2 = 6.0\,\mathrm{\Omega}\), and \(R_3 = 3.0\,\mathrm{\Omega}\). Find the current in each resistor.

    Solution

    Step 1: Combine the parallel pair. \(R_2\) and \(R_3\) are connected between the same two junctions, so they are in parallel. By equation (21.6),

    \[\frac{1}{R_{23}} = \frac{1}{R_2} + \frac{1}{R_3} = \frac{1}{6.0\,\Omega} + \frac{1}{3.0\,\Omega}.\]

    To add the fractions, write them over the common denominator \(6.0\,\Omega\):

    \[\frac{1}{R_{23}} = \frac{1}{6.0\,\Omega} + \frac{2}{6.0\,\Omega} = \frac{3}{6.0\,\Omega} = \frac{1}{2.0\,\Omega}, \qquad\text{so}\qquad R_{23} = 2.0\,\mathrm{\Omega}.\]

    Remember to take the reciprocal at the end: \(3/6.0\) is \(1/R_{23}\), not \(R_{23}\). The “product over sum” form gives the same result in one line, \(R_{23} = R_2R_3/(R_2 + R_3) = (6.0)(3.0)/(6.0 + 3.0) = 18/9.0 = 2.0\,\mathrm{\Omega}\). As expected, \(R_{23}\) is smaller than either \(R_2\) or \(R_3\).

    Step 2: Combine in series. All of the battery current passes first through \(R_1\) and then through the pair, so \(R_1\) and \(R_{23}\) are in series (Figure 21.10b). By equation (21.5),

    \[R_{\text{eq}} = R_1 + R_{23} = 4.0\,\Omega + 2.0\,\Omega = 6.0\,\mathrm{\Omega}\]

    (Figure 21.10c).

    Step 3: Find the battery current. The single equivalent resistor has the whole emf across it, so

    \[I = \frac{\mathcal{E}}{R_{\text{eq}}} = \frac{12\,\mathrm{V}}{6.0\,\Omega} = 2.0\,\mathrm{A}.\]

    This current flows through \(R_1\), since \(R_1\) is in series with the battery: \(I_1 = \boxed{2.0\,\mathrm{A}}\).

    Step 4: Work backward to the voltages. The same \(2.0\,\mathrm{A}\) passes through \(R_1\) and through the equivalent resistor \(R_{23}\), so

    \[V_1 = IR_1 = (2.0\,\mathrm{A})(4.0\,\Omega) = 8.0\,\mathrm{V}, \qquad V_{23} = IR_{23} = (2.0\,\mathrm{A})(2.0\,\Omega) = 4.0\,\mathrm{V}.\]

    Because \(R_2\) and \(R_3\) are in parallel, each has this same \(4.0\,\mathrm{V}\) across it. (Equivalently, by the loop rule, \(V_{23} = \mathcal{E} - V_1 = 12 - 8.0 = 4.0\,\mathrm{V}\).)

    Step 5: Find the branch currents. Apply Ohm’s law to each resistor of the pair separately, using the voltage across it:

    \[I_2 = \frac{V_{23}}{R_2} = \frac{4.0\,\mathrm{V}}{6.0\,\Omega} = \boxed{0.67\,\mathrm{A}}, \qquad I_3 = \frac{V_{23}}{R_3} = \frac{4.0\,\mathrm{V}}{3.0\,\Omega} = \boxed{1.33\,\mathrm{A}}.\]

    The smaller resistor carries the larger current: \(R_3\) has half the resistance of \(R_2\) and carries twice the current.

    Check. At the junction where the current divides, the junction rule requires \(I_2 + I_3 = I_1\): indeed \(0.67 + 1.33 = 2.0\,\mathrm{A}\). Around the loop through \(R_1\) and either resistor of the pair, the loop rule requires the potential differences to add up to the emf: \(8.0 + 4.0 = 12\,\mathrm{V}\).

    Example 21.7: A voltage divider

    Two resistors in series across a source, \(R_1 = 10\,\mathrm{k\Omega}\) and \(R_2 = 5.0\,\mathrm{k\Omega}\) across a \(9.0\,\mathrm{V}\) battery, form a voltage divider. What is the potential difference across \(R_2\)?

    Solution

    The current is \(I = \mathcal{E}/(R_1 + R_2)\), so the potential difference across \(R_2\) is

    \[V_2 = IR_2 = \mathcal{E}\,\frac{R_2}{R_1 + R_2} = (9.0)\frac{5.0}{15} = \boxed{3.0\,\mathrm{V}}.\]

    In series, the emf divides among the resistors in proportion to their resistances. Voltage dividers are everywhere in electronics, supplying a fraction of a voltage to part of a circuit. When one of the resistors is a variable resistor, such as the volume knob on an amplifier, turning the knob varies the output. When one is a sensor whose resistance depends on light or temperature, the output voltage becomes a measurement.

    Checkpoint 21.3

    Three identical bulbs are connected to a battery: bulb \(A\) in series with a parallel pair, \(B\) and \(C\). (a) Rank the bulbs by brightness. (b) Bulb \(C\) is unscrewed. Does bulb \(A\) get brighter or dimmer? Does bulb \(B\)?

    Answer

    Answers to Checkpoints

    Checkpoint 21.3. (a) All the current passes through \(A\), and it splits equally between \(B\) and \(C\), each carrying half. Since \(P = I^2R\) with identical resistances, \(A\) is the brightest (four times as bright as either of the others) and \(B\) and \(C\) are equally bright. (b) With \(C\) removed, the circuit is just \(A\) and \(B\) in series, so the total resistance rises from \(1.5R\) to \(2R\) and the battery current falls: bulb \(A\) gets dimmer. Bulb \(B\) now carries that whole current, \(\mathcal{E}/2R\), rather than half of the old current, \(\tfrac{1}{2}\cdot\mathcal{E}/1.5R = \mathcal{E}/3R\), so \(B\) gets brighter.


    This page titled 21.3: Multiple Resistors in a Circuit: Series vs. Parallel was last modified on Thu, 12 Nov 2026 04:26:45 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.