Opening the book…
Connect a voltmeter to a car battery, and it reads about \(12.6\,\mathrm{V}\). Turn the key, and while the starter motor cranks, the reading drops to perhaps \(10\,\mathrm{V}\), and the headlights dim. The battery’s terminal voltage depends on the current it delivers. An ideal battery would not behave this way; a real one does, because the charge moving through the battery itself, through its electrolyte and electrodes, meets resistance.
A real battery is modeled as an ideal emf \(\mathcal{E}\) in series with a small internal resistance \(r\) (Figure 21.11a). The two cannot be separated; they are inside the same case, and only the terminals \(a\) and \(b\) are accessible. When the battery delivers current \(I\), going from its negative terminal to its positive, the potential rises by \(\mathcal{E}\) across the emf and falls by \(Ir\) across the internal resistance, so the terminal voltage is
Key Equation: Terminal voltage of a real battery
\[V_{\text{terminal}} = \mathcal{E} - Ir. \tag{21.7}\]
Only when no current flows is the terminal voltage equal to the emf. This is how the emf is measured: with a high-resistance voltmeter, which draws almost no current. As the current rises, the terminal voltage falls along a straight line of slope \(-r\) (Figure 21.11b), reaching zero for a short circuit, when the current is \(I_{\text{sc}} = \mathcal{E}/r\). When a real battery is charged, current is forced into its positive terminal, and the terminal voltage is larger than the emf, \(V_{\text{terminal}} = \mathcal{E} + Ir\).
Connected to an external load resistor \(R\), the battery drives a current through both resistances in series:
\[I = \frac{\mathcal{E}}{R + r}. \tag{21.8}\]
If \(R \gg r\), the internal resistance hardly matters, and the battery behaves as an ideal one. If \(R\) is comparable to \(r\), much of the emf is lost inside the battery.
Example 21.8: Starting a car
A car battery has an emf of \(12.6\,\mathrm{V}\) and an internal resistance of \(0.020\,\mathrm{\Omega}\). (a) What is its terminal voltage while it supplies \(150\,\mathrm{A}\) to the starter motor? (b) At the same time, the headlights, which draw \(10\,\mathrm{A}\) at \(12.6\,\mathrm{V}\), are on. By what fraction does their power drop?
Solution
(a) \(V_{\text{terminal}} = \mathcal{E} - Ir = 12.6 - (150)(0.020) = \boxed{9.6\,\mathrm{V}}\). (The headlights’ own \(10\,\mathrm{A}\) lowers it slightly more; we neglect that.)
(b) The headlights have resistance \(R = 12.6/10 = 1.26\,\mathrm{\Omega}\), and at constant resistance their power \(V^2/R\) is proportional to \(V^2\). The power falls to \((9.6/12.6)^2 = 0.58\) of its normal value, a drop of about \(\boxed{42\%}\). The headlights visibly dim while the engine cranks. On a cold morning, when the chemical reactions are slower, the internal resistance rises and the effect is worse, which is why cars are hardest to start in winter.
Getting the most power from a battery. The power delivered to the load is
\[P = I^2R = \frac{\mathcal{E}^2R}{(R + r)^2}.\]
It is zero for \(R = 0\) (no voltage across the load) and falls toward zero for very large \(R\) (almost no current). In between it has a maximum. Setting \(dP/dR = 0\),
\[\frac{dP}{dR} = \mathcal{E}^2\,\frac{(R + r)^2 - 2R(R + r)}{(R + r)^4} = \mathcal{E}^2\,\frac{r - R}{(R + r)^3} = 0,\]
so the power to the load is greatest when the load resistance equals the internal resistance, \(R = r\). This result, called impedance matching in its more general form, is used to connect amplifiers to loudspeakers and antennas to receivers, where getting the most power to the load is the aim. It is not how a power company runs its grid: at \(R = r\), half of the power is wasted inside the source. Where efficiency matters, the load resistance is made much larger than the source’s.
Example 21.9: Matching a load
A \(9.0\,\mathrm{V}\) battery has an internal resistance of \(2.0\,\mathrm{\Omega}\). (a) What is the most power it can deliver to an external resistor, and what resistor does this require? (b) What power does it deliver to a \(20\,\mathrm{\Omega}\) resistor, and what fraction of the battery’s output is that?
Solution
(a) The maximum is at \(R = r = 2.0\,\mathrm{\Omega}\). Then \(I = \mathcal{E}/(2r) = 2.25\,\mathrm{A}\), and \(P_{\max} = I^2r = \mathcal{E}^2/(4r) = (9.0)^2/8.0 = \boxed{10\,\mathrm{W}}\).
(b) With \(R = 20\,\mathrm{\Omega}\), \(I = 9.0/22 = 0.41\,\mathrm{A}\), and \(P = I^2R = \boxed{3.3\,\mathrm{W}}\). The battery’s total output is \(\mathcal{E}I = 3.7\,\mathrm{W}\), so the load receives \(R/(R + r) = 20/22 = \boxed{91\%}\) of it. Less power, but far less waste.
Checkpoint 21.4
A flashlight’s batteries are getting old, and their internal resistance has grown. (a) A voltmeter connected across them, with the flashlight off, still reads nearly their full emf. Why? (b) Why is the bulb dim when the flashlight is switched on?
Answers to Checkpoints
Checkpoint 21.4. (a) A good voltmeter draws almost no current, so there is almost no voltage drop \(Ir\) across the internal resistance, and the terminal voltage \(\mathcal{E} - Ir\) is nearly the full emf. (b) With the bulb connected, a substantial current flows, and the large internal resistance now causes a large drop \(Ir\) inside the battery. The terminal voltage delivered to the bulb falls well below the emf, and the bulb receives much less power.
This page titled 21.4: Ideal vs. Real Batteries was last modified on Thu, 12 Nov 2026 04:26:45 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.
The book could not be loaded just now.