20.2: Resistance

Physics: A Foundation for Scientists and Engineers · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    20.2: Resistance

    Apply the same potential difference across two different objects, a length of copper wire and a length of nichrome wire, say, or a glass rod, and the currents that result are very different. The object’s resistance measures how strongly it opposes the flow of charge. It is defined as the ratio of the potential difference across the object to the current through it:

    Key Equation: Resistance

    \[R = \frac{V}{I}. \tag{20.4}\]

    The SI unit of resistance is the ohm (\(\Omega\)), named for Georg Simon Ohm: \(1\,\Omega = 1\,\mathrm{V/A}\). A copper connecting wire has a resistance of a small fraction of an ohm; the filament of a lamp a few hundred ohms; the human body, from hand to hand with dry skin, tens of thousands.

    Circuit: a battery connected in a loop to a resistor R, with conventional current I shown.
    Figure 20.4. A battery connected to a resistor. The conventional current \(I\) leaves the battery’s positive terminal (the longer line), passes through the resistor from its high-potential end to its low-potential end, and returns to the negative terminal.
    Figure descriptionA simple circuit diagram. A battery of voltage V, drawn with a long line for its positive terminal on top, is connected by wires around a rectangular loop to a resistor R, drawn as a zigzag, on the right side. Arrows on the wires show the conventional current I flowing out of the positive terminal, clockwise around the loop, down through the resistor and back into the negative terminal.

    A component designed to have a particular resistance is a resistor, drawn in circuit diagrams as a zigzag line (Figure 20.4). Resistors are used to control currents and to set voltages throughout electronic circuits.

    The analogy with water is useful. A potential difference is like a difference in water pressure between the two ends of a pipe; the current is like the rate at which water flows through it; and the resistance is like the narrowness and roughness of the pipe. A given pressure difference pushes more water through a wide, smooth pipe than through a narrow, rough one.

    Example 20.3: The resistance of a lamp and of a person

    (a) A lamp draws \(0.50\,\mathrm{A}\) from a \(120\,\mathrm{V}\) outlet. What is its resistance? (b) With dry skin, the resistance of a person’s body from hand to hand is about \(10^{5}\,\mathrm{\Omega}\); with wet skin it can be as low as \(1000\,\mathrm{\Omega}\). What current would flow through the body if the hands touched the two terminals of a \(120\,\mathrm{V}\) outlet in each case?

    Solution

    (a) \(R = V/I = 120/0.50 = \boxed{240\,\mathrm{\Omega}}\).

    (b) With dry skin, \(I = V/R = 120/10^5 = 1.2\,\mathrm{mA}\), which is enough to feel as a tingle. With wet skin, \(I = 120/1000 = \boxed{0.12\,\mathrm{A}}\). A current of a tenth of an ampere passing through the chest can stop the heart. It is the current, not the voltage directly, that does the harm, and the body’s resistance determines the current. This is why electrical appliances and water should never meet.

    Cylindrical conductor of length L and area A with a potential difference V across it.
    Figure 20.5. A uniform conductor of length \(L\) and cross-sectional area \(A\). A potential difference \(V = V_a - V_b\) drives a current \(I\) through it. Its resistance is \(R = \rho L/A\).
    Figure descriptionA uniform cylindrical conductor of length L and cross-sectional area A, with a potential difference V applied between its ends. The left end is at the higher potential. A uniform electric field E points along the conductor from left to right, and a current I flows through it in the same direction.

    Resistivity

    The resistance of an object depends both on the material it is made of and on its shape and size. Experiment shows that a uniform wire or bar of length \(L\) and cross-sectional area \(A\) (Figure 20.5) has a resistance

    Key Equation: Resistance of a uniform conductor

    \[R = \rho\,\frac{L}{A}. \tag{20.5}\]

    Doubling the length doubles the resistance: the charge must be pushed twice as far. Doubling the area halves it: there are twice as many parallel paths for the charge. The constant \(\rho\), the resistivity of the material, depends only on the material and its temperature, not on the object’s shape. Its unit is the ohm-meter (\(\Omega\cdot\)m). Its reciprocal, \(\sigma = 1/\rho\), is the conductivity. (The same symbols \(\rho\) and \(\sigma\) also stand for charge densities; context makes the meaning clear.)

    For a uniform conductor, the field inside is \(E = V/L\) and the current density is \(J = I/A\). Substituting both into \(R = V/I = \rho L/A\) gives a relation between the field and the current density at each point in the material, the microscopic form of the same idea:

    Key Equation: Field and current density in a material

    \[\vec{E} = \rho\vec{J}, \qquad\text{or}\qquad \vec{J} = \sigma\vec{E}. \tag{20.6}\]

    Table 20.1 lists the resistivities of some materials. Their range is extraordinary. The best conductor, silver, and a good insulator such as Teflon differ by some thirty orders of magnitude, a larger range than for almost any other physical property. Between them lie the semiconductors, such as silicon and germanium, whose resistivity can be adjusted over many orders of magnitude by adding tiny amounts of impurities.

    Table 20.1. Approximate resistivities at \(20\,^{\circ}\mathrm{C}\), and temperature coefficients of resistivity near room temperature.
    MaterialResistivity \(\rho\) (\(\Omega\cdot\)m)Temperature coefficient \(\alpha\) (\(\mathrm{K}^{-1}\))
    Silver\(1.59\times10^{-8}\)\(3.8\times10^{-3}\)
    Copper\(1.68\times10^{-8}\)\(3.9\times10^{-3}\)
    Gold\(2.44\times10^{-8}\)\(3.4\times10^{-3}\)
    Aluminum\(2.65\times10^{-8}\)\(3.9\times10^{-3}\)
    Tungsten\(5.6\times10^{-8}\)\(4.5\times10^{-3}\)
    Iron\(9.7\times10^{-8}\)\(5.0\times10^{-3}\)
    Platinum\(1.06\times10^{-7}\)\(3.9\times10^{-3}\)
    Nichrome\(1.10\times10^{-6}\)\(0.4\times10^{-3}\)
    Carbon (graphite)\(3.5\times10^{-5}\)\(-0.5\times10^{-3}\)
    Germanium (pure)\(0.46\)\(-48\times10^{-3}\)
    Silicon (pure)\(2.3\times10^{3}\)\(-75\times10^{-3}\)
    Glass\(10^{10}\) to \(10^{14}\)—
    Teflon\(10^{22}\) to \(10^{24}\)—

    Why metals resist. A simple model, first proposed by Paul Drude in 1900, explains where resistivity comes from. Between collisions with the metal’s ions, a free electron is accelerated by the field, gaining a velocity \(-eE\tau/m\) over the average time \(\tau\) between collisions, the mean free time. Each collision scrambles its direction, erasing that extra velocity, and the process starts again. The drift velocity is the average gain, \(v_d = eE\tau/m\) in size, so the current density is \(J = nev_d = (ne^2\tau/m)E\). Comparing with \(J = E/\rho\),

    \[\rho = \frac{m}{ne^2\tau}. \tag{20.7}\]

    A material resists current more strongly if it has fewer carriers (\(n\) small) or if they collide more often (\(\tau\) short).

    Example 20.4: Resistance of a copper wire

    Find the resistance of a \(10.0\,\mathrm{m}\) length of copper wire of diameter \(1.00\,\mathrm{mm}\). What is the potential difference across it when it carries \(2.0\,\mathrm{A}\)?

    Solution

    The area is \(A = \pi(0.500\times10^{-3})^2 = 7.85\times 10^{-7}\,\mathrm{m^2}\), so

    \[R = \rho\frac{L}{A} = (1.68\times10^{-8})\frac{10.0}{7.85\times10^{-7}} = \boxed{0.214\,\mathrm{\Omega}}.\]

    The potential difference is \(V = IR = (2.0)(0.214) = \boxed{0.43\,\mathrm{V}}\). Ten meters of ordinary wire has only a fifth of an ohm of resistance, which is why the connecting wires in a circuit can usually be treated as having none at all.

    Example 20.5: The mean free time in copper

    Use equation (20.7) to find the mean free time between collisions for the conduction electrons in copper.

    Solution

    Solving for \(\tau\), with \(n = 8.49\times 10^{28}\,\mathrm{m^{-3}}\),

    \[\tau = \frac{m}{ne^2\rho} = \frac{9.11\times10^{-31}}{(8.49\times10^{28})(1.602\times10^{-19})^2(1.68\times10^{-8})} = \boxed{2.5\times 10^{-14}\,\mathrm{s}}.\]

    An electron in copper suffers some forty trillion collisions every second. The simple model gives the right size for \(\tau\), but explaining its value properly, and why electrons pass freely through a perfect crystal and scatter only from its imperfections and vibrations, requires the quantum mechanics of Part III.

    Resistivity and temperature. As a metal warms, its ions vibrate more vigorously, electrons collide with them more often, \(\tau\) shortens, and the resistivity rises. Over moderate temperature ranges the increase is nearly linear:

    Key Equation: Temperature dependence of resistivity

    \[\rho = \rho_0\left[1 + \alpha(T - T_0)\right], \tag{20.8}\]

    where \(\rho_0\) is the resistivity at a reference temperature \(T_0\) (usually \(20\,^{\circ}\mathrm{C}\)) and \(\alpha\) is the temperature coefficient of resistivity. The resistance of a given conductor changes in the same proportion, \(R = R_0[1 + \alpha(T - T_0)]\). For semiconductors \(\alpha\) is negative: heating frees more charge carriers, and the increase in \(n\) outweighs the decrease in \(\tau\).

    Example 20.6: A platinum resistance thermometer

    A platinum thermometer has a resistance of \(100.0\,\mathrm{\Omega}\) at \(0\,^{\circ}\mathrm{C}\). Its resistance in a pot of liquid is \(138.5\,\mathrm{\Omega}\). What is the temperature of the liquid? (For platinum near these temperatures, \(\alpha = 3.85\times 10^{-3}\,\mathrm{K^{-1}}\) relative to \(0\,^{\circ}\mathrm{C}\).)

    Solution

    Solving \(R = R_0[1 + \alpha(T - T_0)]\) for \(T\),

    \[T = T_0 + \frac{R/R_0 - 1}{\alpha} = 0 + \frac{1.385 - 1}{3.85\times10^{-3}} = \boxed{100\,^{\circ}\mathrm{C}}.\]

    The liquid is boiling water. Platinum resistance thermometers of exactly this kind, called “Pt100” sensors, are among the most accurate and widely used thermometers in industry.

    Note: Superconductors

    In 1911 Heike Kamerlingh Onnes cooled mercury in liquid helium and found that below \(4.2\,\mathrm{K}\) its resistance did not merely become small: it vanished completely. A current set up in a loop of superconductor circulates for years with no battery at all. Many metals and compounds become superconducting when cold enough, some ceramics at temperatures above \(77\,\mathrm{K}\), the boiling point of liquid nitrogen. Superconducting wire carries the enormous currents in the magnets of MRI scanners and particle accelerators. Superconductivity cannot be explained by the classical Drude picture at all; it is a quantum effect, in which electrons pair up and move through the crystal together without scattering.

    Checkpoint 20.2

    (a) A wire is stretched to twice its original length, keeping its volume fixed. By what factor does its resistance change? (Hint: what happens to its cross-sectional area?) (b) Why does an incandescent bulb draw its largest current in the instant after it is switched on, and why do bulbs most often burn out at that moment?

    Answer

    Answers to Checkpoints

    Checkpoint 20.2. (a) Doubling the length at fixed volume halves the cross-sectional area. Since \(R = \rho L/A\), the length doubling doubles \(R\) and the area halving doubles it again: the resistance rises by a factor of \(4\). (b) A metal’s resistivity rises with temperature. A cold filament has a resistance several times smaller than when it glows at operating temperature, so at switch-on it draws a surge of current, several times its normal value, until it heats up. That surge heats the filament fastest at its thinnest spot, and the sudden thermal stress is what most often breaks a worn filament at that moment.


    This page titled 20.2: Resistance was last modified on Thu, 12 Nov 2026 04:27:00 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.