Opening the book…
Any net flow of charge is an electric current. If a net charge \(dQ\) passes through a cross-section of a wire in a time \(dt\), the current is the rate of flow,
Key Equation: Electric current
\[I = \frac{dQ}{dt}, \qquad I = \frac{\Delta Q}{\Delta t}\ \text{(steady current)}. \tag{20.1}\]
The second form holds when the current is steady, so that the same charge passes each second. The SI unit of current is the ampere (A), usually shortened to amp in everyday speech. One ampere is one coulomb per second: \(1\,\mathrm{A} = 1\,\mathrm{C/s}\). It is named for André-Marie Ampère, whose work on the magnetic effects of currents you will meet in Chapter 23. A phone charger delivers one or two amperes, a household circuit up to fifteen or twenty, and the starter motor of a car a couple of hundred. The signals in a computer chip involve microamperes or less.
The direction of current. Current is a flow with a direction, but a charge can carry it either way: positive charge moving to the right and negative charge moving to the left both carry charge to the right (Figure 20.1). By convention, the direction of current is the direction in which positive charge would flow. This is the choice Chapter 15 warned about. In a metal wire, the charge carriers are electrons, so they actually move opposite to the direction of the current. In other conductors, such as salt water, the ions of both signs move, in opposite directions, and both contribute to a current in the same direction. For almost everything in circuits the distinction does not matter, and we will simply speak of current flowing from the high-potential end of a wire toward the low-potential end, the way positive charge would.
Current needs a field. In Chapter 17 we found that the field inside a conductor in electrostatic equilibrium is zero. A conductor carrying a current is not in equilibrium: charges are moving through it. To keep them moving there must be a field inside the conductor, pointing along the wire, and so a potential difference exists between its ends. That is the job of a battery or a generator: to maintain a potential difference, and with it a field, that keeps the charges flowing. The charge carriers are not used up. In a steady current, as much charge flows out of any section of wire as flows in, so the current is the same at every point along a single wire, and at a junction where wires meet, the total current flowing in equals the total flowing out. Both facts are consequences of the conservation of charge, and both will be central to the circuits of Chapter 21.
Example 20.1: Charge through a phone charger
A phone charges for \(1.5\,\mathrm{h}\) at a steady current of \(2.0\,\mathrm{A}\). (a) How much charge passes through the charging cable? (b) How many electrons is that?
Solution
(a) With \(\Delta t = (1.5)(3600) = 5400\,\mathrm{s}\),
\[\Delta Q = I\,\Delta t = (2.0\,\mathrm{A})(5400\,\mathrm{s}) = \boxed{1.1\times 10^{4}\,\mathrm{C}}.\]
(b) Dividing by the charge of one electron,
\[N = \frac{\Delta Q}{e} = \frac{1.08\times10^{4}}{1.602\times10^{-19}} = \boxed{6.7\times 10^{22}\,\mathrm{}}\ \text{electrons},\]
about a tenth of a mole. Battery capacities are often quoted in milliampere-hours (mAh), which is a unit of charge: \(1\,\mathrm{mAh} = (10^{-3}\,\mathrm{A})(3600\,\mathrm{s}) = 3.6\,\mathrm{C}\). This charge corresponds to \(3000\,\mathrm{mAh}\), a typical phone battery.
Current Density
The current tells how much charge crosses a whole cross-section of a wire each second. To describe the flow at each point inside the conductor, we use the current density \(\vec{J}\), the current per unit area through a surface perpendicular to the flow. For a current \(I\) spread uniformly over a cross-section of area \(A\),
\[J = \frac{I}{A}, \tag{20.2}\]
measured in \(\,\mathrm{A/m^2}\). The current density is a vector, pointing in the direction of the current, that is, the direction positive charges move, and so along the field in the conductor.
Drift velocity. Current density connects directly to the motion of the charge carriers. Suppose a conductor contains \(n\) charge carriers per unit volume, each of charge \(q\), and that they move along the wire with an average velocity \(\vec{v}_d\), called the drift velocity. In a time \(\Delta t\), every carrier within a distance \(v_d\,\Delta t\) of a given cross-section passes through it (Figure 20.2). Those carriers fill a cylinder of volume \(Av_d\,\Delta t\), so the charge that crosses is \(\Delta Q = nqAv_d\,\Delta t\), and the current is \(I = \Delta Q/\Delta t = nqAv_d\). Dividing by \(A\):
Key Equation: Current density and drift velocity
\[\vec{J} = nq\vec{v}_d, \qquad I = nqAv_d. \tag{20.3}\]
For electrons, \(q = -e\), so \(\vec{v}_d\) points opposite to \(\vec{J}\), as it must.
Example 20.2: The drift speed of electrons in a copper wire
A copper wire of the size used in household wiring has a diameter of \(2.05\,\mathrm{mm}\) and carries a current of \(10.0\,\mathrm{A}\). Copper has about one free electron per atom, which gives \(n = 8.49\times 10^{28}\,\mathrm{m^{-3}}\). Find (a) the current density and (b) the drift speed of the electrons.
Solution
(a) The cross-sectional area is \(A = \pi(1.025\times10^{-3})^2 = 3.30\times 10^{-6}\,\mathrm{m^2}\), so
\[J = \frac{I}{A} = \frac{10.0}{3.30\times10^{-6}} = \boxed{3.03\times 10^{6}\,\mathrm{A/m^2}}.\]
(b) From equation (20.3),
\[v_d = \frac{J}{ne} = \frac{3.03\times10^{6}}{(8.49\times10^{28})(1.602\times10^{-19})} = \boxed{2.2\times 10^{-4}\,\mathrm{m/s}},\]
about a fifth of a millimeter per second. At this rate an electron needs over an hour to travel a meter of wire.
Why the lamp comes on at once. If the electrons crawl, why does the lamp light instantly? Because the wire is already full of free electrons, from the switch all the way to the filament. When the switch closes, the change in the field travels along the wire at nearly the speed of light, and electrons everywhere in the circuit, including those already in the filament, start drifting almost at once. It is like a garden hose that is already full of water: turn on the tap and water comes out of the far end immediately, even though no drop of water has traveled from the tap to the nozzle. The energy is carried by the field, not by the electrons’ journey.
The drift speed is also tiny compared with the electrons’ random motion. Even with no current, the free electrons in a metal dart about at speeds of order \(10^{6}\,\mathrm{m/s}\), colliding constantly with the vibrating ions of the metal. Their velocities point in every direction and average to zero. The field adds a slight bias to this frantic random motion, a slow drift superimposed on it (Figure 20.3a). Follow many electrons at once and the pattern is clearer: every path looks aimless, yet on average they all creep the same way (Figure 20.3b). The drift velocity is the average of all that motion, and it is billions of times smaller than the typical speed.
Checkpoint 20.1
Two copper wires carry the same current. Wire \(B\) has twice the diameter of wire \(A\). (a) Compare the current densities in the two wires. (b) Compare the drift speeds. (c) A wire made of a metal with twice as many free electrons per cubic meter as copper carries the same current density as wire \(A\). How does its drift speed compare?
Answers to Checkpoints
Checkpoint 20.1. (a) Doubling the diameter quadruples the area, so with the same current \(J = I/A\) is four times smaller in wire \(B\). (b) The drift speed is \(v_d = J/(ne)\), and the two wires have the same \(n\) (both copper), so wire \(B\)’s drift speed is also four times smaller. (c) With the same \(J\) but twice the carrier density, \(v_d = J/(ne)\) is half that in wire \(A\): more carriers share the work, so each can move more slowly.
This page titled 20.1: Electric Current was last modified on Thu, 12 Nov 2026 04:27:00 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.
The book could not be loaded just now.