19.3: Dielectrics

Physics: A Foundation for Scientists and Engineers · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    19.3: Dielectrics

    Most real capacitors are not empty. The space between the plates is filled with an insulating material such as plastic, ceramic, glass, paper, or oil, called a dielectric. In 1837 Faraday found that filling the space between a capacitor’s plates with an insulator increases its capacitance, by a factor that depends only on the material. That factor is the dielectric constant \(\kappa\) (the Greek letter kappa) of the material:

    Key Equation: Capacitance with a dielectric

    \[C = \kappa C_0, \tag{19.7}\]

    where \(C_0\) is the capacitance of the same capacitor with vacuum between its plates. For vacuum \(\kappa = 1\) exactly; for every material \(\kappa > 1\). Table 19.1 lists some values. For a parallel-plate capacitor filled with a dielectric, \(C = \kappa\epsilon_0A/d\), and it is often convenient to combine the two constants into the permittivity of the material, \(\epsilon = \kappa\epsilon_0\), so that \(C = \epsilon A/d\).

    A dielectric does a second job, just as important in practice. Every insulator breaks down and conducts if the field in it is made strong enough; the air in a spark gap does so at about \(3\times 10^{6}\,\mathrm{V/m}\). The largest field a material can withstand without breaking down is its dielectric strength. Most dielectrics are far stronger than air, so filling a capacitor with one allows a much higher voltage across the same gap. The two effects together are why nearly every practical capacitor contains a dielectric.

    Table 19.1. Approximate dielectric constants and dielectric strengths of some materials at room temperature. Water’s large \(\kappa\) comes from its permanently polar molecules; it is too conductive, in practice, to serve as a capacitor dielectric.
    MaterialDielectric constant \(\kappa\)Dielectric strength (\(\,\mathrm{V/m}\))
    Vacuum\(1\) (exactly)—
    Air (dry, 1 atm)\(1.00059\)\(3\times10^{6}\)
    Paper\(3.7\)\(16\times10^{6}\)
    Teflon\(2.1\)\(60\times10^{6}\)
    Polystyrene\(2.6\)\(24\times10^{6}\)
    Pyrex glass\(4.7\)\(14\times10^{6}\)
    Mica\(5.4\)\(100\times10^{6}\)
    Water (pure, \(20\,^{\circ}\mathrm{C}\))\(80\)—
    Strontium titanate\(\sim 300\)\(8\times10^{6}\)
    A parallel-plate capacitor with a dielectric slab filling the space between its plates.
    Figure 19.4. A dielectric in a capacitor. The field polarizes the molecules, leaving a layer of induced charge on each face of the slab, opposite in sign to the charge on the nearby plate. The induced charges partly cancel the field of the plates, reducing it to \(E_0/\kappa\) inside the dielectric.
    Figure descriptionA parallel-plate capacitor with a dielectric slab filling the space between its plates. The left plate is positive and the right plate negative. Inside the slab, small oval molecules are all polarized with their negative ends toward the positive plate and positive ends toward the negative plate. At the slab's left face a layer of negative induced charge faces the positive plate, and at its right face a layer of positive induced charge faces the negative plate. Below, two arrows compare the fields: the long arrow E sub zero from the plate charges, and a shorter arrow E equals E sub zero over kappa for the net field inside the dielectric.

    How a dielectric works. The explanation lies in polarization, which we first met in Section 15.1. Place a slab of dielectric in the field between the plates (Figure 19.4). The field pulls the electron cloud of each molecule slightly one way and its nuclei the other, and if the molecules are already polar, like water, it tends to swing them into line (Section 16.5). Either way, the material fills up with tiny dipoles aligned with the field. Inside the material, the positive end of each dipole sits next to the negative end of its neighbor, and the charges cancel. But at the two surfaces they do not: a thin layer of negative induced charge appears on the face next to the positive plate, and a layer of positive induced charge on the face next to the negative plate. These induced charges produce a field of their own, pointing opposite to the field of the charges on the plates, and so the net field inside the dielectric is weaker:

    \[E = \frac{E_0}{\kappa}. \tag{19.8}\]

    With the same charge \(Q\) on the plates, a weaker field means a smaller potential difference, \(V = Ed = V_0/\kappa\), and therefore a larger capacitance, \(C = Q/V = \kappa C_0\).

    Note: Gauss’s law in a dielectric

    The induced charges are real charges, and Gauss’s law, \(\oint\vec{E}\cdot d\vec{A} = q_{\text{enc}}/\epsilon_0\), holds with \(q_{\text{enc}}\) counting them. But they are tied to the molecules and cannot be controlled directly. For a uniform, linear dielectric, their effect is to reduce the field by exactly the factor \(\kappa\) everywhere, so Gauss’s law can be rewritten using only the free charge, the charge we actually put on the conductors:

    \[\oint\kappa\vec{E}\cdot d\vec{A} = \frac{q_{\text{free}}}{\epsilon_0}.\]

    Every result of Chapters 15 through 18 therefore carries over to charges embedded in a dielectric by replacing \(\epsilon_0\) with \(\epsilon = \kappa\epsilon_0\). Two charges in water, for instance, attract each other \(80\) times more weakly than in vacuum, which is why salt dissolves so readily in water: the ions’ strong attraction is weakened enough for thermal motion to pull them apart.

    Example 19.6: Inserting a dielectric, with and without the battery

    A \(50\,\mathrm{pF}\) air-filled capacitor is charged by a \(100\,\mathrm{V}\) battery. A slab of Pyrex (\(\kappa = 4.7\)) is then slid in to fill the space between the plates. Find the new capacitance, charge, voltage, and stored energy (a) if the battery remains connected and (b) if the battery was disconnected first.

    Solution

    Before the slab: \(Q_0 = C_0V_0 = (50\times10^{-12})(100) = 5.0\,\mathrm{nC}\), and \(U_0 = \tfrac12 C_0V_0^2 = 0.25\,\mathrm{\mu J}\). In both cases the new capacitance is \(C = \kappa C_0 = \boxed{235\,\mathrm{pF}}\).

    (a) With the battery connected, \(V = \boxed{100\,\mathrm{V}}\) is fixed. The battery supplies more charge, \(Q = CV = \boxed{23.5\,\mathrm{nC}}\), and the energy rises to \(U = \tfrac12 CV^2 = \kappa U_0 = \boxed{1.2\,\mathrm{\mu J}}\).

    (b) With the battery disconnected, \(Q = \boxed{5.0\,\mathrm{nC}}\) is fixed. The voltage falls to \(V = Q/C = V_0/\kappa = \boxed{21\,\mathrm{V}}\), and the energy falls to \(U = Q^2/2C = U_0/\kappa = \boxed{0.053\,\mathrm{\mu J}}\).

    In case (b) the capacitor loses energy as the slab goes in. The missing energy went into work done on the slab: the fringing field at the edge of the plates pulls a dielectric into the gap, just as a charged comb pulls on a scrap of paper. You would have to hold the slab back to keep it from being sucked in.

    Example 19.7: The largest charge a capacitor can hold

    A capacitor is made of two sheets of aluminum foil, each \(0.40\,\mathrm{m^2}\), separated by a sheet of polystyrene \(0.050\,\mathrm{mm}\) thick. Find (a) its capacitance, (b) the largest voltage it can withstand, and (c) the largest charge it can hold.

    Solution

    (a) With \(\kappa = 2.6\),

    \[C = \frac{\kappa\epsilon_0A}{d} = \frac{(2.6)(8.85\times10^{-12})(0.40)}{5.0\times10^{-5}} = \boxed{1.8\times 10^{-7}\,\mathrm{F}} = 0.18\,\mathrm{\mu F}.\]

    (b) The field must not exceed the dielectric strength, \(24\times 10^{6}\,\mathrm{V/m}\), so

    \[V_{\max} = E_{\max}d = (24\times10^{6})(5.0\times10^{-5}) = \boxed{1.2\times 10^{3}\,\mathrm{V}}.\]

    (c) \(Q_{\max} = CV_{\max} = (1.8\times10^{-7})(1.2\times10^{3}) = \boxed{2.2\times 10^{-4}\,\mathrm{C}}\). With air between the same foils, the capacitance would be \(2.6\) times smaller and the maximum voltage \(8\) times smaller. Rolled up into a compact cylinder, sheets like these make the familiar film capacitor.

    Checkpoint 19.3

    (a) Why can’t a dielectric constant be less than \(1\)? (Hint: which way do the induced charges point?) (b) A capacitor filled with a dielectric is disconnected from its battery, and the dielectric is then removed. Does the voltage increase or decrease? Does the stored energy increase or decrease? Where does the change in energy come from?

    Answer

    Answers to Checkpoints

    Checkpoint 19.3. (a) The field of the capacitor polarizes the dielectric, and the induced surface charges produce a field pointing opposite to the applied field. The field inside is therefore reduced, never increased, so \(E = E_0/\kappa\) requires \(\kappa \geq 1\). (\(\kappa = 1\) only for a vacuum, which cannot be polarized.) (b) With the battery disconnected, \(Q\) is fixed. Removing the dielectric reduces \(C\) by the factor \(\kappa\), so \(V = Q/C\) increases and \(U = Q^2/2C\) increases. The extra energy comes from the work you do pulling the dielectric out: the capacitor’s field attracts the dielectric inward, so you must pull against that attraction.


    This page titled 19.3: Dielectrics was last modified on Thu, 12 Nov 2026 04:26:46 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.