26.5: Series RLC Circuits

Physics: A Foundation for Scientists and Engineers · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    26.5: Series RLC Circuits
    Series RLC circuit: an ac source with a resistor, inductor and capacitor in one loop.
    Figure 26.5. (a) A series RLC circuit. (b) Its phasor diagram. The voltage phasors of the resistor, inductor, and capacitor are in phase with, \(90^\circ\) ahead of, and \(90^\circ\) behind the current. They add as vectors to the source voltage \(V_m\), which leads the current by \(\phi\).
    Figure descriptionPanel a: a series RLC circuit, an ac source on the left connected in a loop through a resistor R along the top, an inductor L on the right side, and a capacitor C along the bottom. Panel b: a phasor diagram for the case where the inductive reactance is larger than the capacitive reactance. The current phasor I sub m lies along the horizontal axis. The resistor's voltage phasor V sub R lies along it too. The inductor's voltage phasor V sub L points straight up and the capacitor's V sub C straight down, shorter. Their sum, V sub L minus V sub C, points up. The source voltage phasor V sub m is the diagonal of the rectangle formed by V sub R and V sub L minus V sub C, at angle phi above the current phasor.

    Now connect a resistor, an inductor, and a capacitor in series with an ac source (Figure 26.5a). The same current \(i = I_m\sin(\omega t - \phi)\) flows through all three elements; the source voltage is \(v = V_m\sin\omega t\), and \(\phi\), the phase constant, is the angle by which the current lags the source voltage. We want \(I_m\) and \(\phi\).

    By the loop rule, the source voltage equals the sum of the three voltages at every instant, \(v = v_R + v_L + v_C\). But the three are not in phase, so their amplitudes do not simply add. This is where phasors pay off. Draw the current phasor \(I_m\) (Figure 26.5b). The resistor’s voltage phasor, of length \(V_R = I_mR\), is in phase with it. The inductor’s, \(V_L = I_mX_L\), is \(90^\circ\) ahead of it, and the capacitor’s, \(V_C = I_mX_C\), is \(90^\circ\) behind it. The instantaneous values add, so the phasors add as vectors, and the source phasor \(V_m\) is their vector sum. Since \(V_L\) and \(V_C\) point in opposite directions, they combine to \(V_L - V_C\), at right angles to \(V_R\), and by the Pythagorean theorem

    \[V_m^2 = V_R^2 + (V_L - V_C)^2 = I_m^2\left[R^2 + (X_L - X_C)^2\right].\]

    So \(V_m = I_mZ\), where

    Key Equation: Impedance and phase of a series RLC circuit

    \[Z = \sqrt{R^2 + (X_L - X_C)^2}, \qquad \tan\phi = \frac{X_L - X_C}{R}. \tag{26.7}\]

    The quantity \(Z\) is the impedance of the circuit, measured in ohms; it generalizes resistance to ac circuits, with \(I_m = V_m/Z\) and \(I_{\text{rms}} = V_{\text{rms}}/Z\). If \(X_L > X_C\), the circuit is inductive: \(\phi\) is positive, and the current lags the source voltage. If \(X_C > X_L\), it is capacitive: \(\phi\) is negative, and the current leads. A series circuit with only some of the elements is handled by setting the missing reactance or resistance to zero.

    Example 26.6: A series RLC circuit

    A series circuit has \(R = 200\,\mathrm{\Omega}\), \(L = 0.40\,\mathrm{H}\), and \(C = 10\,\mathrm{\mu F}\), driven by a \(120\,\mathrm{V}\) (rms), \(60\,\mathrm{Hz}\) source. Find (a) the reactances, (b) the impedance, (c) the rms current, (d) the phase constant, and (e) the rms voltage across each element.

    Solution

    (a) With \(\omega = 2\pi(60) = 377\,\mathrm{rad/s}\):

    \[X_L = \omega L = (377)(0.40) = 151\,\mathrm{\Omega}, \qquad X_C = \frac{1}{\omega C} = \frac{1}{(377)(10\times10^{-6})} = 265\,\mathrm{\Omega}.\]

    (b) The impedance is

    \[Z = \sqrt{R^2 + (X_L - X_C)^2} = \sqrt{(200)^2 + (151 - 265)^2} = \boxed{230\,\mathrm{\Omega}}.\]

    (c) \(I_{\text{rms}} = V_{\text{rms}}/Z = 120/230 = \boxed{0.52\,\mathrm{A}}\).

    (d) \(\tan\phi = (X_L - X_C)/R = -114/200 = -0.57\), so \(\phi = \boxed{-30^\circ}\). The circuit is capacitive, and the current leads the source voltage by \(30^\circ\).

    (e) \(V_R = I_{\text{rms}}R = \boxed{104\,\mathrm{V}}\), \(V_L = I_{\text{rms}}X_L = \boxed{79\,\mathrm{V}}\), and \(V_C = I_{\text{rms}}X_C = \boxed{138\,\mathrm{V}}\). These add up to far more than \(120\,\mathrm{V}\), and \(V_C\) alone exceeds it. There is no contradiction: the voltages reach their peaks at different times, and it is their phasors that add, \(\sqrt{104^2 + (79 - 138)^2} = 120\,\mathrm{V}\).

    Resonance

    The current in a series RLC circuit, \(I_{\text{rms}} = V_{\text{rms}}/Z\), depends on the driving frequency through the reactances. At low frequency the capacitor’s reactance is huge; at high frequency the inductor’s is. In between, at the frequency where they are equal, \(X_L = X_C\), they cancel, the impedance takes its smallest possible value, \(Z = R\), and the current is greatest. Setting \(\omega L = 1/\omega C\) gives the resonant frequency:

    Key Equation: Resonance in a series RLC circuit

    \[\omega_0 = \frac{1}{\sqrt{LC}}, \qquad I_{\text{rms, max}} = \frac{V_{\text{rms}}}{R}. \tag{26.8}\]

    This is exactly the natural frequency of the LC circuit of Section 26.1. When the source drives the circuit at its own natural frequency, the response is largest: this is resonance. At resonance, the phase constant is zero; the circuit behaves like the resistor alone, with the voltages across the inductor and capacitor, which can each be much larger than the source voltage, exactly canceling each other.

    Resonance curve: rms current in a series RLC circuit against driving frequency.
    Figure 26.6. Resonance. The rms current in a series RLC circuit peaks at the resonant frequency \(\omega_0 = 1/\sqrt{LC}\). With a smaller resistance (solid), the peak is higher and sharper.
    Figure descriptionA graph of the rms current in a series RLC circuit against the driving angular frequency omega, in units of the resonant frequency omega zero, from 0 to 2.5. Two curves are shown, for the same inductor and capacitor with two different resistances. Both peak at omega equals omega zero. The curve for the smaller resistance has a peak four times higher and much narrower; the curve for the larger resistance has a low, broad peak.

    The smaller the resistance, the higher and sharper the peak in the current (Figure 26.6). A circuit with a sharp resonance responds strongly to frequencies close to \(\omega_0\) and hardly at all to others. That is how a radio selects a station: the signals of all the stations produce tiny emfs in the antenna, but only the one whose frequency matches the tuning circuit’s resonant frequency drives a large current. The same physics, a driven oscillator responding most strongly at its natural frequency, is treated for mechanical systems in Section 28.9.

    Example 26.7: Resonance

    For the circuit of Example 26.6, find (a) the resonant frequency and (b) the rms current and the rms voltage across the capacitor at resonance.

    Solution

    (a) \(\omega_0 = 1/\sqrt{LC} = 1/\sqrt{(0.40)(10\times10^{-6})} = 500\,\mathrm{rad/s}\), so \(f_0 = \omega_0/2\pi = \boxed{80\,\mathrm{Hz}}\).

    (b) At resonance \(Z = R\), so \(I_{\text{rms}} = 120/200 = \boxed{0.60\,\mathrm{A}}\). The capacitor’s reactance there is \(X_C = 1/\omega_0C = 200\,\mathrm{\Omega}\), so \(V_C = (0.60)(200) = \boxed{120\,\mathrm{V}}\). With a smaller resistance, say \(20\,\mathrm{\Omega}\), the current at resonance would be \(6.0\,\mathrm{A}\) and the capacitor’s voltage \(1200\,\mathrm{V}\), ten times the source voltage. Resonant circuits can build up dangerously large voltages from modest sources, and their components must be rated for them.

    Checkpoint 26.3

    A series RLC circuit is driven below its resonant frequency. (a) Is its reactance mainly inductive or capacitive? (b) Does the current lead or lag the source voltage? (c) To bring it into resonance at this frequency, should you increase or decrease the capacitance?

    Answer

    Answers to Checkpoints

    Checkpoint 26.3. (a) Below resonance, \(X_C = 1/\omega C\) is larger than \(X_L = \omega L\), so the reactance is mainly capacitive. (b) The current leads the source voltage, as it does in a purely capacitive circuit. (c) Increase it. Resonance occurs at \(\omega_0 = 1/\sqrt{LC}\), so to lower \(\omega_0\) down to the driving frequency you must make \(C\) larger (which also makes \(X_C\) smaller, until it equals \(X_L\)).


    This page titled 26.5: Series RLC Circuits was last modified on Thu, 12 Nov 2026 04:26:59 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.