Opening the book…
4.1.1 The Inlet
The basic function of the inlet is to transport the air to the compressor. The subsonic compressors are designed for an axial Mach number of Ma = 0.5–0.6. When the flight Mach number exceeds 0.5 or 0.6, as in commercial and military aircraft, the inlet is required to slow down the air efficiently. Because the main function of an inlet is to diffuse the flow, it is also called a diffuser. As the flow velocity decreases, static pressure increases. One of the main challenges facing an inlet designer is preventing boundary layer separation. This challenge is even greater for supersonic aircraft. At Mach 0.9, the inlet acts as a diffuser that slows the air to around Mach 0.5. However, at Mach 2 or higher, shock waves form and reduce total pressure, leaving only about 72% of the initial total pressure. At Mach 3, a strong normal shock wave retains only about 33% of the total pressure.
From the \(h\) -\(s\) diagram, we observe that the freestream static state \(\left(0\right)\) and the freestream total state \(\left(t0\right)\) are separated isentropically by the specific kinetic energy \(\dfrac{V^2_0}{2}\), as defined by the relationship between static and stagnation states.
The fictitious total state \(\left(t2s\right)\) is also separated isentropically from state \(\left(0\right)\) by an ideal kinetic energy amount, establishing \(p_{t2}\) as its stagnation pressure. The enthalpy gap between \(\left(t0\right)\) and \(\left(t2s\right)\) represents the portion of kinetic energy dissipated into heat through fluid friction, boundary layer growth, and shock wave losses. Consequently, a smaller gap between \(\left(t2s\right)\) and \(\left(t0\right)\) signifies a more efficient diffusion process.
Inlet Adiabatic Efficiency (\(\eta_d\))
To quantify this performance, we define the inlet adiabatic efficiency (\({\eta }_d\)) using the fictitious state \(\left(t2s\right)\) as a Figure of merit:
\[\eta_d\equiv \dfrac{h_{t2s}-h_0}{h_{t0}-h_0} = \dfrac{\left(\dfrac{V^2_0}{2}\right)_\mathrm{ideal} \dfrac{V^2_0}{2} \nonumber \]
Dividing both the numerator and denominator by \(h_0\) yields a practical form expressed in terms of thermodynamic property ratios:
\[{\eta }_d=\dfrac{\dfrac{h_{t2s}}{h_0}-1}{\dfrac{h_{t0}}{h_0}-1}=\dfrac{\dfrac{T_{t2s}}{T_0}-1}{\dfrac{h_{t0}}{h_0}-1} \nonumber \]
Applying the isentropic temperature-pressure relation between states \(\left(t2s\right)\) and \(\left(0\right)\), along with the temperature ratio parameter \({\tau }_r=\dfrac{T_{t0}}{T_0}=1+\dfrac{k-1}{2}{Ma}^2_0\):
\[{\eta }_d=\dfrac{{\left(\dfrac{p_{t2}}{p_0}\right)}^{\dfrac{k-1}{k}}-1}{\dfrac{k-1}{2}{Ma}^2_0}=\dfrac{{\left(\dfrac{p_{t2}}{p_0}\right)}^{\dfrac{k-1}{k}}-1}{{\tau }_r-1} \nonumber \]
Pressure Ratio Relations
For a given flight altitude (\(p_0\)), flight Mach number (\({Ma}_0\)), and known inlet efficiency (\({\eta }_d\)), the exit total pressure \(p_{t2}\) can be isolated directly:
\[\dfrac{p_{t2}}{p_0}={\left[1+{\eta }_d\left(\dfrac{k-1}{2}\right){Ma}^2_0\right]}^{\dfrac{k}{k-1}} \nonumber \]
Note: For an ideal, 100% efficient inlet (\({\eta }_d=1.0\) ), this expression simplifies back to the standard isentropic stagnation pressure relation.
Total Pressure Recovery (\({\boldsymbol\pi}_{\boldsymbol{d}}\) )
An alternative Figure of merit for evaluating inlet performance is the inlet total pressure recovery (\(\pi_d\)), defined as the total pressure ratio between the engine compressor face and the freestream flight condition:
\[\pi_d\equiv \dfrac{p_{t2}}{p_{t0}} \nonumber \]
The relationship between adiabatic efficiency (\({\eta }_d\)) and total pressure recovery (\(\pi_d\)) is derived by expanding the pressure ratio:
\[\dfrac{p_{t2}}{p_0}= \left (\dfrac{p_{t2}}{p_{t0}}\right) \left (\dfrac{p_{t0}}{p_0}\right)={ \left [1+{\eta }_d \left (\dfrac{k-1}{2}\right){Ma}^2_0\right]}^{\dfrac{k}{k-1}} \nonumber \]
Solving for \(\pi_d\):
\[\pi_d=\dfrac{ \left [1+{\eta }_d \left (\dfrac{k-1}{2}\right){Ma}^2_0\right]}^{\dfrac{k}{k-1}}{\dfrac{p_{t0}}{p_0}}={ \left [\dfrac{1+{\eta }_d \left (\dfrac{k-1}{2}\right){Ma}^2_0}{1+ \left (\dfrac{k-1}{2}\right){Ma}^2_0}\right]}^{\dfrac{k}{k-1}}=\dfrac{ \left [1+{\eta }_d \left (\dfrac{k-1}{2}\right){Ma}^2_0\right]}^{\dfrac{k}{k-1}}{\pi_r} \nonumber \]
where \(\pi_r={ \left (1+\dfrac{k-1}{2}{Ma}^2_0\right)}^{\dfrac{k}{k-1}}\) is the ram pressure ratio.
Thus far, our analysis has focused on cruise conditions—the high-speed end of the flight envelope—where inlets function strictly as diffusers. However, under low-speed flight or takeoff conditions, the captured stream tube accelerates toward the engine face (\(A_0>A_2\)) as seen in Figure 2, causing the inlet to operate as a nozzle rather than a diffuser.
Under these low-speed conditions, the flow stagnation point shifts onto the outer cowl (is the smooth, curved outer skin and leading edge of the engine inlet housing) as indicated in Figure 3 While the aerodynamics of the external nacelle geometry strongly influence drag divergence and play a critical role in overall engine installation and propulsion system integration, standard cycle analysis typically focuses on internal propulsion performance and omits these external drag effects. At zero forward speed (static engine testing) or very low forward speeds, the incoming flow path must accelerate rapidly to feed the engine. This acceleration causes the static pressure along the streamlines to drop from the ambient pressure (\(p_0\)) down to the engine face static pressure (\(p_2\)), accompanied by a corresponding velocity increase from \(V_0\approx 0\) to \(V_2\).
To guide this accelerating flow smoothly into the engine without boundary layer separation or severe flow distortion, static ground test rigs utilize a bellmouth inlet. The smooth, flared geometry of the bellmouth minimizes contraction losses and ensures uniform flow delivery across the compressor face during ground tests.
4.1.2 Compressor
The thermodynamic cycle of a gas generator begins with the mechanical compression of intake air. Because the compressed discharge air possesses a higher energy state, the compressor requires work input to operate. During steady-state operation, this power is driven by the turbine via a connecting shaft. For engine startup, external power is supplied by auxiliary systems such as electric, or hydraulic starters. The air flowing through the compressor is modeled as an essentially adiabatic process, assuming negligible heat exchange between the internal fluid and the ambient environment. Consequently, even in a real compressor analysis, we treat the process as adiabatic while accounting for non-reversible thermodynamic losses. Power is transferred to the working fluid in a compressor through rows of rotating blades (rotors) mounted on one or more spinning shafts (spools). As each rotor blade alters the swirl of the fluid, it experiences an equal and opposite reaction torque. For a rotor spinning at angular velocity \(ω\) under a torque \(τ\), the mechanical power \(\mathcal{P}\) delivered to the fluid is given by:
\[\mathcal{P}=τ\cdot ω \nonumber \]
A typical multi-stage axial-flow compressor contains hundreds of rotor blades operating under this mechanical principle. Consequently, the rate of mechanical energy transfer \({\mathcal{P}}_c\) in modern compressors larger than the rate of heat loss through the casing wall (\({\dot{Q}}_w\)):
\[{\mathcal{P}}_c\gg {\dot{Q}}_w \nonumber \]
Because heat transfer is negligible (\({\dot{Q}}_w\approx 0\)), real compressor flows are modeled as adiabatic. For a steady-flow actual mass flow rate \({\dot{m}}_0\), the compressor power and performance parameters are defined as:
\[{\mathcal{P}}_c={\dot{m}}_0\left(h_{t3}-h_{t2}\right) \nonumber \]
\[π_c\equiv \dfrac{p_{t3}}{p_{t2}},\qquad τ_c\equiv \dfrac{T_{t3}}{T_{t2}} \nonumber \]
where \(π_c\) is the total pressure ratio, \(τ_c\) is the total temperature ratio, and \(h_{t2},h_{t3}\) are the inlet and exit stagnation enthalpies as shown in Figure 2, respectively. Although assumed adiabatic, real compression processes are inherently irreversible. The principal sources of irreversibility are:
- Viscous Boundary Layers: Wall friction along the blade surfaces and casing leads to boundary layer growth, wake formation, and vortex shedding.
- Shock Waves: Passages with relative supersonic flow experience shock formation, creating sudden entropy jumps.
To quantify irreversibility, two efficiency metrics are commonly used, Compressor Adiabatic Efficiency (\(η_c\)) and Compressor Polytropic Efficiency (\(e_c\)).
Evaluating a real compression process on an enthalpy-entropy (\(h--s\)) diagram demonstrates an entropy rise (\(Δs_c\)) from the actual inlet state \(t2\) (\(p_{t2},T_{t2}\)) to the exit state \(t3\) (\(p_{t3},T_{t3}\)). Because entropy increases during actual compression, the standard isentropic relationship does not apply directly to actual total states:
\[τ_c\neq π^{\dfrac{k-1}{k}}_c \nonumber \]
Due to irreversible losses, the actual temperature ratio \(τ_c\) is always greater than the ideal isentropic temperature ratio (\(τ_{c,s}=T_{t3s}/T_{t2}\)).
The adiabatic efficiency \(η_c\) is defined as the ratio of ideal (isentropic) specific work input to actual specific work input:
\[η_c\equiv \dfrac{h_{t3s}-h_{t2}}{h_{t3}-h_{t2}}=\dfrac{Δh_{t,\mathrm{isentropic}}}{Δh_{t,\mathrm{actual}}} \nonumber \]
Dividing the numerator and denominator by \(h_{t2}=C_pT_{t2}\) yields:
\[η_c=\dfrac{\dfrac{T_{t3s}}{T_{t2}}-1}{\dfrac{T_{t3}}{T_{t2}}-1}=\dfrac{\left(\dfrac{T_{t3s}}{T_{t2}}\right)-1}{τ_c-1} \nonumber \]
Since states \(t2\) and \(t3s\) share the same isentrope, \(T_{t3s}/T_{t2}\) converts directly to the total pressure ratio \(π_c\):
\[\dfrac{T_{t3s}}{T_{t2}}={\left(\dfrac{p_{t3s}}{p_{t2}}\right)}^{\dfrac{k-1}{k}}={\left(\dfrac{p_{t3}}{p_{t2}}\right)}^{\dfrac{k-1}{k}}=π^{\dfrac{k-1}{k}}_c \nonumber \]
Substituting this into the efficiency expression yields the final form for compressor adiabatic efficiency:
\[η_c=\dfrac{π^{\dfrac{k-1}{k}}_c-1}{τ_c-1} \nonumber \]
4.1.3 Combustor
Within the combustor, fuel mixes with compressed air to initiate an exothermic chemical reaction that releases heat. An ideal combustor is modeled as a reversible heater, assuming frictionless wall flow and near-zero flow velocity. Under these ideal conditions, total pressure is fully conserved. However, In a real combustor, total pressure decreases due to wall friction, turbulent mixing, and chemical heat release occurring at a finite Mach number:
\[π_b=\dfrac{p_{t4}}{p_{t3}}<1\qquad \mathrm{(Real}~\mathrm{Combustion}~\mathrm{Chamber)} \nonumber \]
\[π_b=1\qquad \mathrm{(Ideal}~\mathrm{Combustion}~\mathrm{Chamber)} \nonumber \]
Kerrebrock provides an empirical approximation for the combustor total pressure ratio \(π_b\) as a function of the average burner Mach number \({Ma}_b\):
\[π_b\approx 1-ε\left(\dfrac{k}{2}{Ma}^2_b\right)\qquad \mathrm{where}~1<ε<2 \nonumber \]
This expression shows that total pressure loss is directly proportional to the average dynamic pressure ratio (\(\dfrac{k}{2}{Ma}^2_b\)) inside the burner, scaled by the coefficient \(ε\). For example, for subsonic flow with an average Mach number \({Ma}_b=0.2\), \(ε=2\), and \(k\approx 1.33\), the pressure ratio is:
\[π_b\approx 1-2\left(\dfrac{1.33}{2}{\left(0.2\right)}^2\right)\approx 0.95 \nonumber \]
This demonstrates a \(\mathrm{\sim}\) 5% loss in total pressure. While this model is invalid for supersonic combustion, it highlights the thermodynamic advantage of maintaining low flow velocities in conventional combustors. A fuel’s energy capacity is characterized by its heat of reaction (\(Q_R\)), which represents the thermal energy released per unit mass during complete chemical reaction. In practical combustion chambers, physical volume constraints prevent the complete theoretical heat release from being fully realized. The actual fraction of chemical energy converted into thermal energy is defined by the burner (or combustion) efficiency (\(η_b\)):
\[η_b\equiv \dfrac{Q_{R,\mathrm{Actual}}}{Q_{R,\mathrm{Ideal}}} \nonumber \]
Modern gas turbine engines achieve high combustion performance, with burner efficiencies typically reaching 99%. In thermodynamic cycle analysis, loss parameters across the combustor are accounted for using two non-ideal factors: the total pressure ratio (\(π_b<1\)) and the burner efficiency (\(η_b<1\)). Real combustors exhibit a drop in total pressure \(Δp_{t,\mathrm{burner}}\) from inlet to exit (\(p_{t4}<p_{t3}\)) as seen in Figure 4. The peak cycle temperature \(T_{t4}\) is strictly limited by turbine cooling technology, high-temperature material selection, and thermal barrier coatings. Current state-of-the-art values typically range from 3200–3600 \(\mathrm{{}^\circ}\) R. The temperature rise \(ΔT_t=T_{t4}-T_{t3}\) directly reflects the thermal energy added by the fuel. The rate of heat input is approximately:
\[{\dot{Q}}_{\mathrm{in}}\approx {\dot{m}}_0C_p{\left(ΔT_t\right)}_{\mathrm{burner}} \nonumber \]
Applying a steady-flow energy balance across the combustion chamber accounts for the incoming air enthalpy, added chemical fuel energy, and outgoing mixture enthalpy:
\[{\dot{m}}_0h_{t3}+{\dot{m}}_fQ_Rη_b=\left({\dot{m}}_0+{\dot{m}}_f\right)h_{t4} \nonumber \]
Dividing by the air mass flow rate \({\dot{m}}_0\) and substituting the fuel-to-air ratio \(f=\dfrac{{\dot{m}}_f}{{\dot{m}}_0}\) yields the fundamental governing equation:
\[h_{t3}+fQ_Rη_b=\left(1+f\right)h_{t4} \nonumber \]
This equation allows for the direct determination of \(f\) given the target turbine inlet temperature \(T_{t4}\). In an ideal combustor, heat addition occurs along a constant total pressure isobar (\(p_{t3}=p_{t4}\)). In a real combustor, viscous friction and heat release at finite velocities cause an entropy increase and a drop in total pressure, shifting the exit state to a lower isobar (\(p_{t4}<p_{t3}\)). By isolating the unknown parameter \(f\) from the combustor energy balance equation, the fuel-to-air ratio is explicitly written as:
\[f=\dfrac{h_{t4}-h_{t3}}{η_bQ_R-h_{t4}} \nonumber \]
The denominator in this expression is completely specified when the fuel lower heating value (\(Q_R\)), burner efficiency (\(η_b\)), and target turbine inlet total temperature (\(T_{t4}\)) are given. Similarly, the compressor discharge enthalpy (\(h_{t3}\)) in the numerator is predetermined by the compressor pressure ratio, compressor isentropic efficiency, and inlet ambient conditions. Consequently, applying the energy balance across the burner serves as the primary method to calculate \(f\).
In standard thermodynamic cycle analysis, it is customary to express this relation using non-dimensional temperature and enthalpy ratios. Dividing the numerator and denominator by the ambient free-stream static enthalpy (\(h_0\)) yields:
\[f=\dfrac{\dfrac{h_{t4}}{h_0}-\dfrac{h_{t3}}{h_0}}{\dfrac{η_bQ_R}{h_0}-\dfrac{h_{t4}}{h_0}}=\dfrac{τ_λ-τ_rτ_c}{\dfrac{η_bQ_R}{h_0}-τ_λ} \nonumber \]
4.1.4 Turbine
Conceptually, the turbine acts as a primary flow-control boundary analogous to a valve—separating the high-pressure combustion zone from the low-pressure downstream components. In a gas turbine engine, the turbine represents the first throttling station; for supersonic aircraft, the throat of the exhaust nozzle serves as the second and final throttling station.
As the gas expands through the turbine and nozzle as shown in Figure 5, it undergoes a substantial drop in static pressure and static temperature. This continuous expansion process generates both the mechanical power required to drive the compressor and the overall propulsive thrust for the aircraft. The turbine transmits shaft power directly to the compressor via a shared connecting shaft. Functionally, this expansion is the continuous-flow equivalent of the power stroke in a reciprocating internal combustion engine.
The actual power \({\mathcal{P}}_{t,\mathrm{actual}}\) produced in an uncooled turbine account for fluid friction and losses, whereas the ideal power \({\mathcal{P}}_{t,\mathrm{ideal}}\) represents the maximum power output achieved via a reversible, isentropic expansion between the same total pressures:
\[{\mathcal{P}}_{t,\mathrm{actual}}={\dot{m}}_t\left(h_{t4}-h_{t5}\right)={\dot{m}}_tΔh_{t,\mathrm{actual}} \nonumber \]
\[{\mathcal{P}}_{t,\mathrm{ideal}}={\dot{m}}_t\left(h_{t4}-h_{t5s}\right)={\dot{m}}_tΔh_{t,\mathrm{isentropic}} \nonumber \]
The total working gas mass flow rate \({\dot{m}}_t\) includes both the entering air mass flow rate (\({\dot{m}}_0\)) and the added fuel mass flow rate (\({\dot{m}}_f\)):
\[{\dot{m}}_t={\dot{m}}_0+{\dot{m}}_f=\left(1+f\right){\dot{m}}_0 \nonumber \]
where \(f=\dfrac{{\dot{m}}_f}{{\dot{m}}_0}\) is the fuel-to-air ratio.
The turbine adiabatic efficiency (\(η_t\)) is defined as the ratio of actual work output to ideal (isentropic) work output:
\[η_t\equiv \dfrac{h_{t4}-h_{t5}}{h_{t4}-h_{t5s}}=\dfrac{Δh_{t,\mathrm{actual}}}{Δh_{t,\mathrm{isentropic}}} \nonumber \]
Dividing both the numerator and denominator by \(h_{t4}=C_pT_{t4}\) yields:
\[η_t=\dfrac{1-\dfrac{T_{t5}}{T_{t4}}}{1-\dfrac{T_{t5s}}{T_{t4}}} \nonumber \]
Because states \(t4\) and \(t5s\) lie on the same isentrope, their temperature ratio relates directly to the turbine total pressure ratio \(π_t\equiv \dfrac{p_{t5}}{p_{t4}}\) via the isentropic relation:
\[\dfrac{T_{t5s}}{T_{t4}}={\left(\dfrac{p_{t5s}}{p_{t4}}\right)}^{\dfrac{k-1}{k}}={\left(\dfrac{p_{t5}}{p_{t4}}\right)}^{\dfrac{k-1}{k}}=π^{\dfrac{k-1}{k}}_t \nonumber \]
Defining the actual total temperature ratio as \(τ_t\equiv \dfrac{T_{t5}}{T_{t4}}\), the turbine adiabatic efficiency simplifies to:
\[η_t=\dfrac{1-τ_t}{1-π^{\dfrac{k-1}{k}}_t} \nonumber \]
To evaluate individual turbine stages or small differential expansions, we define the turbine polytropic (small-stage) efficiency (\(e_t\)) as the ratio of differential actual enthalpy drop to differential isentropic enthalpy drop:
\[e_t\equiv \dfrac{dh_t}{dh_{ts}}=\dfrac{dh_t}{\left(\dfrac{dp_t}{ρ_t}\right)} \nonumber \]
Assuming a perfect gas (\(dh_t=C_pdT_t\)) and integrating across the expansion stage relates the total temperature ratio \(τ_t\) and total pressure ratio \(π_t\):
\[τ_t=π^{\dfrac{\left(k-1\right)e_t}{k}}_t\qquad \mathrm{or}\qquad π_t=τ^{\dfrac{k}{\left(k-1\right)e_t}}_t \nonumber \]
When \(e_t=1\), the expression reduces directly to the standard isentropic relationship between the temperature and pressure ratios. By substituting \(π_t\) from Equation 4.42 into Equation 4.40, we derive the relation connecting turbine adiabatic efficiency (\(η_t\)) and polytropic efficiency (\(e_t\)):
For a constant small-stage efficiency (e.g., \(e_t=0.90\)), the turbine adiabatic efficiency \(η_t\) increases as the total expansion increases (i.e., as \(\dfrac{1}{τ_t}\) grows larger).
This behavior contrasts with compressor performance, where the overall adiabatic efficiency (\(η_c\)) decreases as pressure ratio increases. Fluid friction and inefficiencies generate heat that increases the gas temperature at subsequent stages. Because compressing a hotter fluid requires more work, each additional compressor stage increases the required power input. Fluid friction and internal losses dissipate energy as heat back into the expanding gas stream. This frictionally generated heat increases the enthalpy of the gas entering subsequent stages, allowing downstream turbine blades to recover a fraction of those thermal losses as additional shaft power. The total temperature ratio \(τ_t\) across the turbine is governed by an energy balance connecting the turbine, the compressor, and any auxiliary power extractions (such as an electrical generator) attached to the spool.
Assuming a simplified system where the turbine exclusively powers the compressor (\({\mathcal{P}}_t={\mathcal{P}}_c\)):
\[{\mathcal{P}}_t={\mathcal{P}}_c \nonumber \]
\[{\dot{m}}_0\left(1+f\right)\left(h_{t4}-h_{t5}\right)={\dot{m}}_0\left(h_{t3}-h_{t2}\right) \nonumber \]
Dividing by the ambient static enthalpy (\(h_0\)) and simplifying yields the non-dimensional energy balance equation:
\[\left(1+f\right)τ_λ\left(1-τ_t\right)=τ_r\left(τ_c-1\right) \nonumber \]
where: \(τ_λ\) is temperature parameter representing maximum cycle energy (\(h_{t4}/h_0\)), \(τ_t\) is turbine total temperature ratio (\(T_{t5}/T_{t4}\)), \(τ_r\) is free-stream ram temperature ratio (\(T_{t0}/T_0\)), \(τ_c\) is Compressor total temperature ratio (\(T_{t3}/T_{t2}\)). Isolating the turbine expansion parameter \(τ_t\) yields:
\[τ_t=1-\dfrac{τ_r\left(τ_c-1\right)}{\left(1+f\right)τ_λ} \nonumber \]
4.1.5 Nozzle
The primary function of an aircraft engine exhaust nozzle (as shown in Figure 6) is to accelerate the expanding working fluid to produce propulsive force. The critical performance parameter for any exhaust system is the gross thrust (\(F_g\)), given by:
\[F_g={\dot{m}}_9V_9+\left(p_9-p_0\right)A_9 \nonumber \]
Momentum Thrust (\({\dot{m}}_9V_9\)) is the force generated by the change in fluid momentum. Where, Pressure Thrust (\(\left(p_9-p_0\right)A_9\)) is the force resulting from any static pressure imbalance at the nozzle exit plane (\(A_9\)) relative to ambient pressure (\(p_0\)). Beyond propulsion requirements, modern exhaust systems are critical to aircraft stealth design (is a discipline in military engineering that reduces an aircraft’s visibility). The exhaust flow leaves distinct operational "signatures" (are the physical traces an engine leaves behind) including thermal infrared emissions, visible exhaust plumes, smoke, and high acoustic noise levels that must be minimized in low-observable military platforms. As flow accelerates through a converging nozzle, the static pressure continuously decreases (\(dp/dx<0\)). This establishes a favorable pressure gradient, which stabilizes boundary layer development and minimizes flow separation. Consequently, nozzle losses are significantly lower and easier to model than those in diffusers and inlets, which operate under adverse pressure gradients.
In subsonic compressible aerodynamics, a convergent duct accelerates a subsonic flow up to a maximum limit of \(Ma=1\), which can only occur at the duct’s minimum cross-sectional area (the exit plane). For any subsonic exhaust jet (\({Ma}_9<1\)), the static pressure at the exit plane (\(p_9\)) inherently equilibrates with the surrounding atmospheric pressure (\(p_0\)):
\[\mathrm{If} ~ Ma_9=Ma_{\mathrm{jet}}<1,\qquad \mathrm{then}~p_{\mathrm{jet}}=p_{\mathrm{ambient}}\qquad \left(p_9=p_0\right) \nonumber \]
While mandatory for subsonic flows, expanding the exhaust fully to match ambient pressure is also achievable and highly desirable for sonic (\({Ma}_9=1\)) and supersonic (\({Ma}_9>1\)) exit flows. When an exhaust stream expands such that its exit static pressure precisely equals ambient pressure, the nozzle is operating in a perfectly expanded state which is if:
\[p_{\mathrm{jet}}=p_{\mathrm{ambient}}\qquad \left(p_9=p_0\right),\qquad \mathrm{then}~\mathrm{the}~\mathrm{nozzle}~\mathrm{is}~\mathrm{perfectly}~\mathrm{expanded}~\longrightarrow F_g=F_{g,\mathrm{max}} \nonumber \]
Under this condition, the pressure thrust term \(\left(p_9-p_0\right)A_9\) drops to zero, and the nozzle achieves its maximum possible gross thrust (\(F_{g,\mathrm{max}}\)) for the given energy state. A real nozzle flow experiences total pressure losses due to boundary layer viscous dissipation and shock formation. Despite these non-ideal effects, a real nozzle can still achieve perfect expansion to ambient static pressure (\(p_9=p_0\)). In compressible duct flow, the exit static pressure \(p_9\) depends directly on the nozzle area ratio (\(A_{\mathrm{exit}}/A_{\mathrm{throat}}\equiv A_9/A_8\)) and the Nozzle Pressure Ratio (NPR):
\[\mathrm{NPR}\equiv \dfrac{p_{t7}}{p_0} \nonumber \]
This behavior is governed by two key aerodynamic principles for convergent and convergent-divergent (C–D) nozzles. When the nozzle pressure ratio reaches or exceeds its critical threshold, the flow velocity at the nozzle throat reaches sonic speed (\({Ma}_8=1.0\)). If:
\[~\mathrm{NPR}\ge {\left(\mathrm{NPR}\right)}_{\mathrm{critical}},\qquad \mathrm{then}~{Ma}_8=1.0\qquad \left(\mathrm{Throat}~\mathrm{is}~\mathrm{choked}\right) \nonumber \]
As a practical approximation, the nozzle throat chokes when the exit static pressure drops to roughly half of the upstream total pressure (\(p_{\mathrm{throat}}\approx \dfrac{1}{2}p_{t7}\)), If:
\[\mathrm{If}~\dfrac{p_{t7}}{p_0}\ge \sim 2,\qquad \mathrm{then}~{Ma}_8=1.0\qquad \left(\mathrm{Throat}~\mathrm{can}~\mathrm{be}~\mathrm{choked}\right) \nonumber \]
Similar to the inlet section, the performance of an exhaust nozzle can be evaluated using the nozzle adiabatic efficiency (\(η_n\)). This metric compares the actual kinetic energy realized at the exit plane against the ideal kinetic energy from an isentropic expansion over the same total-to-static pressure ratio:
\[η_n\equiv \dfrac{h_{t7}-h_9}{h_{t7}-h_{9s}}=\dfrac{V^2_9/2}{V^2_{9s}/2} \nonumber \]
where: \(h_{t7}\) is total enthalpy at the nozzle inlet (Station 7), \(h_9\) is actual static enthalpy at the nozzle exit plane (Station 9), \(h_{9s}\) is ideal static enthalpy achieved via an isentropic expansion to ambient pressure, \(V_9\) is actual gas velocity at the exit plane, \(V_{9s}\) is ideal exit velocity resulting from lossless, isentropic expansion
In an under-expanded or over-expanded nozzle flow, the nozzle pressure ratio (\(\mathrm{NPR}\equiv p_{t7}/p_0\)) and the exit pressure ratio (\(p_0/p_9\)) quantify the static pressure mismatch at the exit plane:
- Under-Expanded (\(p_9>p_0\)): The nozzle expansion area ratio (\(A_9/A_8\)) is too small, preventing the fluid from expanding fully to ambient static pressure before exiting the duct.
- Over-Expanded (\(p_9<p_0\) ): The nozzle expansion area ratio (\(A_9/A_8\)) is excessively large, causing the fluid to expand past ambient static pressure inside the duct.
For a perfectly expanded nozzle, the exit static pressure precisely matches the ambient atmospheric pressure (\(p_9=p_0\)). Under this condition, the nozzle adiabatic efficiency (\(η_n\)) simplifies directly to:
\[η_n=\dfrac{{\mathrm{NPR}\mathrm{}}^{\dfrac{k-1}{k}}-π^{-\dfrac{k-1}{k}}_n}{{\mathrm{NPR}}^{\dfrac{K-1}{k}}-1} \nonumber \]
where: \(\mathrm{NPR}\) is nozzle Pressure Ratio (\(p_{t7}/p_0\)), \(π_n\) is nozzle total pressure ratio (\(p_{t9}/p_{t7}\)), reflecting internal total pressure losses (\(π_n\le 1.0\)), k is ratio of specific heats (\(c_p/c_v\))
This page titled 4.1: Gas Generator Components was last modified on Wed, 18 Nov 2026 07:22:37 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by .
The book could not be loaded just now.