6.2: Thermodynamics Relations for Engine Process

Aircraft Engine: Design and Analysis · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    6.2: Thermodynamics Relations for Engine Process

    The overall engine operating parameters of greatest interest which can be determined from a thermodynamic analysis of the engine operating cycle are:

    The indicated fuel conversion efficiency \(η_{f,i}\):

    \[η_{f,i}=\dfrac{W_{c,i}}{m_fQ_{\mathrm{LHV}}} \nonumber \]

    (which, since the combustion efficiency is unity, is equal to the indicated thermal conversion efficiency \(η_{t,i}\))

    The indicated mean effective pressure (\(imep\)):

    \[imep=\dfrac{W_{c,i}}{V_d}=\dfrac{m_fQ_{\mathrm{LHV}}η_{f,i}}{V_d} \nonumber \]

    \(W_{c,i}\), the indicated work per cycle, is the sum of the compression stroke work and the expansion stroke work:

    \[W_{c,i}=W_C+W_E \nonumber \]

    image1.png
    Figure 1. The \(P-V\) diagrams representing the Constant-Volume (Otto), Constant-Pressure (Diesel), and Limited-Pressure (Dual)- AI creation

    The following relationships (Figure 1) are obtained by applying the first and second laws of thermodynamics to the cylinder contents:

    Compression stroke:

    \[\dfrac{v_1}{v_2}=r_c \nonumber \]

    Since the process is adiabatic and reversible:

    \[s_2=s_1 \nonumber \]

    The compression work is:

    \[W_C=U_1-U_2=m\left(u_1-u_2\right) \nonumber \]

    Combustion process:

    For the constant-volume cycle:

    \[v_3=v_2,\qquad u_3-u_2=0 \nonumber \]

    For the constant-pressure cycle:

    \[p_3=p_2,\qquad h_3-h_2=0 \nonumber \]

    For the limited-pressure cycle:

    \[v_{3a}=v_2,\qquad p_{3b}=p_{3a} \nonumber \]

    and

    \[u_{3a}-u_2=0,\qquad h_{3b}-h_{3a}=0 \nonumber \]

    Expansion stroke:

    For the constant-volume cycle:

    \[\dfrac{v_4}{v_3}=r_c,\qquad s_4=s_3 \nonumber \]

    and the expansion work is:

    \[W_E=U_3-U_4=m\left(u_3-u_4\right) \nonumber \]

    For the constant-pressure cycle:

    \[p_3=p_2,\qquad \dfrac{v_4}{v_2}=r_c,\qquad s_4=s_3 \nonumber \]

    and the expansion work is:

    \[W_E=U_3-U_4+p_2(V_3-V_2) \nonumber \]

    \[ =m\left(u_3-u_4\right)+p_2(v_3-v_2) \nonumber \]

    For the limited-pressure cycle:

    \[\dfrac{v_4}{v_{3a}}=r_c,\qquad p_{3b}=p_{3a},\qquad s_4=s_{3b} \nonumber \]

    and the expansion work is: \(W_E= m[\left(h_{3b}-h_4\right)+p_4v_4-p_3v_{3a}]\)

    The indicated fuel conversion efficiency is:

    1. For the constant-volume cycle:
    2. For the constant-pressure cycle:
    3. For the limited-pressure cycle:

    The state of the mixture at point 1 in the cycle depends on the intake mixture properties and the residual gas properties at the end of the exhaust stroke.

    When the exhaust valve opens at point 4, the cylinder pressure is above the exhaust manifold pressure and a blowdown process occurs. In the ideal exhaust process model, this blowdown occurs with the piston stationary at BC. During this blowdown process, the gas which remains inside the cylinder expands isentropically. The gases escaping from the cylinder undergo an unrestrained expansion or throttling process which is irreversible. It is assumed that the kinetic energy acquired by each gas element as it is accelerated through the exhaust valve is dissipated in a turbulent mixing process in the exhaust port into internal energy and flow work. Since it is also assumed that no heat transfer occurs, the enthalpy of each element of gas after it leaves the cylinder remains constant.

    The gas remaining in the cylinder expands isentropically along the line 4–5. The first element of gas which leaves the cylinder at point 4 enters the exhaust manifold at state \(a\) on the pressure \(=p_e\) line. An element that leaves the cylinder at an intermediate state \(b\) on the expansion line 4–5 would enter the exhaust manifold at state \(c\). At the end of the blowdown process the gas in the cylinder and the last gas to leave have the same state—5. There is, therefore, a gradient in temperature within the exhausted gas. The temperature of the first element exhausted, \(T_a\), is slightly less than \(T_4\) ; the temperature of the last element exhausted is \(T_5\).

    A displacement of gas out of the cylinder follows the blowdown process as the piston moves from BC to TC. If heat-transfer and kinetic energy dissipation effects are neglected, no change in thermodynamic state of the gas occurs. In this displacement process, the mass of gas within the cylinder at the end of the blowdown process is further decreased by the ratio \(V_5/V_6\).

    The mass of residual gas \(m_r\) in the cylinder at point 6 in the cycle is obtained by first determining the state of the gas (\(T_5\), \(v_5\)) at the end of the blowdown process following an isentropic expansion from \(p_4\) to \(p_e\) and then by reducing the cylinder volume to the clearance volume \(V_6\). The residual mass fraction is thus given by:

    \[\dfrac{m_r}{m}=x_r=\dfrac{v_4/v_5}{r_c}=\dfrac{v_2}{v_5} \nonumber \]

    The average state of the exhausted gas can be determined by considering the open system defined by the piston face, cylinder walls, and cylinder head, shown in Fig. 5-4. Applying the first law of thermodynamics for an open system gives:

    \[U_6-U_4=p_e\left(V_4-V_6\right)-H_e \nonumber \]

    where \(H_e\) is the enthalpy of the mass of gas exhausted from the cylinder. The average specific exhaust enthalpy is, therefore:

    \[{\overline{h}}_e=\dfrac{m_4u_4-m_6u_6+p_eV_d}{m_4-m_6} \nonumber \]

    which, with \(p=p_e\), defines the average exhausted-gas state.

    The mixture temperature at the end of the intake stroke and at the start of the compression stroke (point 1 in Fig. 1) can now be determined. Application of the first law between points 6 and 1 gives:

    \[U_1-U_6=-p_i\left(V_1-V_6\right)+\left(m_1-m_6\right)h_i \nonumber \]

    or

    \[m_1u_1-m_6u_6=-p_i\left(V_1-V_6\right)+\left(m_1-m_6\right)h_i \nonumber \]

    or

    \[m_1h_1=m_6h_6+\left(m_1-m_6\right)h_i+V_2\left(p_i-p_e\right) \nonumber \]

    where \(h_i\) is the specific enthalpy of the inlet mixture and \(p_1=p_i\).

    Note that when \(p_i<p_e\), part of the residual gas in the cylinder at the end of the exhaust stroke will flow into the intake system when the intake valve opens. This flow will cease when the cylinder pressure equals \(p_i\). However, provided no heat transfer occurs, this backflow will not affect Eqs. [GrindEQ__5_19_] above, since the flow of residual through the intake valve is a constant enthalpy process.

    In many engines, the closing of the exhaust valve and the opening of the intake valve overlap. Flow of exhausted gases from the exhaust system through the cylinder into the intake system can then occur.

    In the four-stroke engine cycle, work is done on the piston during the intake and the exhaust processes. The work done by the cylinder gases on the piston during exhaust is:

    \[W_e=p_e\left(V_2-V_1\right) \nonumber \]

    The work done by the cylinder gases on the piston during intake is:

    \[W_i=p_i\left(V_1-V_2\right) \nonumber \]

    The net work to the piston over the exhaust and intake strokes, the pumping work, is:

    \[W_p=\left(p_i-p_e\right)\left(V_1-V_2\right) \nonumber \]

    which, for the cylinder gas system, is negative for \(p_i<p_e\) and positive for \(p_i>p_e\).

    The pumping mean effective pressure (\(pmep\)) is usually defined as a positive quantity. Thus:

    1. For \(p_i<p_e\):
    2. For \(p_i>p_e\):

    The net and gross indicated mean effective pressures are related by:

    \[imep_n=imep_g-\left(p_e-p_i\right) \nonumber \]

    The net indicated fuel conversion efficiency is related to the gross indicated fuel conversion efficiency by:

    \[η_{f,in}=η_{f,ig}\left(1-\dfrac{p_e-p_i}{imep_g}\right) \nonumber \]

    If the working fluid in these ideal cycles is assumed to be an ideal gas, with \(c_v\) and \(c_p\) constant throughout the engine operating cycle, the equations developed in the previous section which describe engine performance and efficiency can be further simplified. We will use the notation of Fig. 1.

    Constant-Volume Cycle:

    The compression work becomes:

    \[W_C=mc_v\left(T_1-T_2\right) \nonumber \]

    The expansion work becomes:

    \[W_E=mc_v\left(T_3-T_4\right) \nonumber \]

    The \(m_fQ_{\mathrm{LHV}}\), can be related to the temperature rise during combustion. For the working fluid model under consideration, the \(U\left(T\right)\) lines for the reactants and products on a \(U\) -\(T\) diagram such as Fig. 2 are parallel and have equal slopes, of magnitude \(c_v\). Hence, for a constant-volume adiabatic combustion process:

    \[mc_v\left(T_3-T_2\right)=m_fQ_{\mathrm{LHV}} \nonumber \]

    image2.png
    Figure 2. The \(u-T\) (or \(h-T\)) thermodynamic diagram- AIA creation

    If insufficient air is available for complete combustion of the fuel. The right-hand side of the equation should then be \(η_cm_fQ_{\mathrm{LHV}}\) , where \(η_c\) is the combustion efficiency:

    \[η_c=\dfrac{H_R-H_P}{m_fQ_{HV}} \nonumber \]

    Note that the heating values at constant volume and constant pressure are the same for this working fluid. For convenience we will define:

    \[Q^*=\dfrac{m_fQ_{\mathrm{LHV}}}{m} \nonumber \]

    \(Q^*\) is the specific internal energy (and enthalpy) decrease, during isothermal combustion, per unit mass of working fluid.

    The relation for indicated fuel conversion efficiency becomes:

    \[η_{f,i}=\dfrac{\left(T_3-T_4\right)-\left(T_2-T_1\right)}{T_3-T_2}=1-\dfrac{T_4-T_1}{T_3-T_2} \nonumber \]

    Since 1–2 and 3–4 are isentropic processes between the same volumes, \(V_1\) and \(V_2\):

    \[\dfrac{T_2}{T_1}={\left(\dfrac{V_1}{V_2}\right)}^{k-1}=r^{γ-1}_c={\left(\dfrac{V_4}{V_3}\right)}^{k-1}=\dfrac{T_3}{T_4} \nonumber \]

    where \(γ=c_p/c_v\). Hence:

    \[\dfrac{T_4}{T_1}=\dfrac{T_3}{T_2} \nonumber \]

    and Eq. [GrindEQ__5_30_] can be rearranged as:

    \[η_{f,i}=1-\dfrac{1}{r^{k-1}_c} \nonumber \]

    The indicated fuel conversion efficiency increases with increasing compression ratio and decreases as \(k\) decreases.

    The indicated mean effective pressure becomes:

    \[\dfrac{imep}{p_1}=\left(\dfrac{Q^*}{c_vT_1}\right)\left(\dfrac{1}{k-1}\right)\left(\dfrac{r_c}{r_c-1}\right)\left(1-\dfrac{1}{r^{k-1}_c}\right) \nonumber \]

    The dimensionless numbers \(r_c\), k, and \(Q^*/\left(c_vT_1\right)\) are sufficient to describe the characteristics of the constant-volume ideal gas standard cycle, relative to its initial conditions \(p_1,T_1\).

    It is useful to compare the \(imep\) —a measure of the effectiveness with which the displaced volume of the engine is used to produce work—and the maximum pressure in the cycle, \(p_3\). The ratio \(p_3/p_1\) can be determined from the ideal gas law applied at points 2 and 3, and the relation:

    \[\dfrac{T_3}{T_2}=1+\dfrac{Q^*}{c_vT_1r^{k-1}_c} \nonumber \]

    Then give:

    \[\dfrac{imep}{p_3}=\dfrac{1}{\left(k-1\right)r^k_c}\left(\dfrac{r_c}{r_c-1}\right)\dfrac{1-1/r^{k-1}_c}{c_vT_1/Q^*+1/r^{k-1}_c} \nonumber \]

    A high value of \(imep/p_3\) is desirable. Engine weight will increase with increasing \(p_3\) to withstand the increasing stresses in components.

    The indicated fuel conversion efficiency and the ratios \(imep/p_1\) and \(imep/p_3\) for this ideal cycle model do not depend on whether the cycle is throttled or supercharged. However, the relationships between the working fluid properties at points 1 and 6 do depend on the degree of throttling or supercharging. For throttled engine operation, the residual gas mass fraction \(x_r\) can be determined as follows. Since state 5 corresponds to an isentropic expansion from state 4 to \(p=p_e\), \(x_r\) is given by:

    \[x_r=\dfrac

    ParseError: invalid DekiScript (click for details)
    Callstack:
        at (Bookshelves/Aerospace_Engineering/Aircraft_Engine:_Design_and_Analysis/06:_Combustor-_Working_Fluid_and_Models_of_Engine_Cycles/6.03:_Thermodynamics_Relations_for_Engine_Process), /content/body/p[102]/span[1], line 1, column 1
    
    {r_c}=\dfrac
    ParseError: invalid DekiScript (click for details)
    Callstack:
        at (Bookshelves/Aerospace_Engineering/Aircraft_Engine:_Design_and_Analysis/06:_Combustor-_Working_Fluid_and_Models_of_Engine_Cycles/6.03:_Thermodynamics_Relations_for_Engine_Process), /content/body/p[102]/span[2], line 1, column 1
    
    {r_c} \nonumber \]

    Since

    \[\dfrac{p_1}{p_4}=\dfrac{p_1}{p_2}\dfrac{p_2}{p_3}\dfrac{p_3}{p_4}=\dfrac{1}{r^k_c}\dfrac{T_2}{T_3}r^k_c={\left(1+\dfrac{Q^*}{c_vT_1r^{k-1}_c}\right)}^{-1} \nonumber \]

    it follows that

    \[x_r=\dfrac{1}{r_c}\dfrac

    ParseError: invalid DekiScript (click for details)
    Callstack:
        at (Bookshelves/Aerospace_Engineering/Aircraft_Engine:_Design_and_Analysis/06:_Combustor-_Working_Fluid_and_Models_of_Engine_Cycles/6.03:_Thermodynamics_Relations_for_Engine_Process), /content/body/p[106]/span[1], line 1, column 1
    
    ParseError: invalid DekiScript (click for details)
    Callstack:
        at (Bookshelves/Aerospace_Engineering/Aircraft_Engine:_Design_and_Analysis/06:_Combustor-_Working_Fluid_and_Models_of_Engine_Cycles/6.03:_Thermodynamics_Relations_for_Engine_Process), /content/body/p[106]/span[2], line 1, column 1
    
    \nonumber \]

    The residual mass fraction increases as \(p_i\) decreases below \(p_e\), decreases as \(r_c\) increases, and decreases as \(Q^*/\left(c_vT_1\right)\) increases.

    Through a similar analysis, the temperature of the residual gas \(T_6\) can be determined:

    \[\dfrac{T_6}{T_1}={\left(\dfrac{p_e}{p_i}\right)}^{\left(k-1\right)/k}{\left(1+\dfrac{Q^*}{c_vT_1r^{k-1}_c}\right)}^{1/k} \nonumber \]

    The mixture temperature at point 1 in the cycle can be related to the inlet mixture temperature, \(T_i\), For a working fluid with \(c_v\) and \(c_p\) constant, this equation becomes:

    \[c_pT_1=x_rc_pT_6+\left(1-x_r\right)c_pT_i-\dfrac{RT_1}{r_c}\left(\dfrac{p_e}{p_i}-1\right) \nonumber \]

    leads to the relation:

    \[\dfrac{T_1}{T_i}=\dfrac{1-x_r}{1-1/\left(kr_c\right)\left[p_e/p_i+\left(k-1\right)\right]} \nonumber \]

    Extensive results for the constant-volume cycle with \(k=1.4\) can be found in Taylor.

    Limited- and Constant-Pressure Cycles

    The constant-pressure cycle is a limited-pressure cycle with \(p_3=p_2\). For the limited-pressure cycle, the compression work remains:

    \[W_C=mc_v\left(T_1-T_2\right) \nonumber \]

    The expansion work becomes:

    \[W_E=m\left[c_v\left(T_{3b}-T_4\right)+p_3\left(v_{3b}-v_{3a}\right)\right] \nonumber \]

    For the combustion process give:

    \[m_{f,2-3a}Q_{\mathrm{LHV}}=mc_v\left(T_{3a}-T_2\right) \nonumber \]

    \[m_{f,3a-3b}Q_{\mathrm{LHV}}=mc_p\left(T_{3b}-T_{3a}\right) \nonumber \]

    or

    \[m_fQ_{\mathrm{LHV}}=m\left[c_v\left(T_{3a}-T_2\right)+c_p\left(T_{3b}-T_{3a}\right)\right] \nonumber \]

    for a working fluid with \(c_v\) and \(c_p\) constant throughout the cycle.

    Then :

    \[η_{f,i}=1-\dfrac{T_4-T_1}{\left(T_{3a}-T_2\right)+γ\left(T_{3b}-T_{3a}\right)} \nonumber \]

    Use of the isentropic relationships for the working fluid along 1–2 and 3b–4, with the substitutions:

    \[α=\dfrac{p_3}{p_2},\qquad β=\dfrac{V_{3b}}{V_{3a}} \nonumber \]

    leads to the result:

    \[η_{f,i}=1-\dfrac{1}{r^{k-1}_c}\left[\dfrac{αβ^k-1}{αk\left(β-1\right)+α-1}\right] \nonumber \]

    For \(β=1\) this result becomes the constant-volume cycle efficiency. For \(α=1\), this result gives the constant-pressure cycle efficiency as a special case.

    The mean effective pressure is related to \(p_1\) and \(p_3\) via:

    \[\dfrac{imep}{p_1}=\dfrac{Q^*}{c_vT_1\left(-1\right)}\left(\dfrac{r_c}{r_c-1}\right)η_{f,i} \nonumber \]

    \[\dfrac{imep}{p_3}=\dfrac{1}{αr^k_c}\left(\dfrac{Q^*}{c_vT_1}\right)\left(\dfrac{1}{k-1}\right)\left(\dfrac{r_c}{r_c-1}\right)η_{f,i} \nonumber \]

    Cycle Comparison:

    The above expressions are most useful if values for \(k\) and \(Q^*/\left(c_vT_1\right)\) are chosen to match real working fluid properties. The average values of \(k_u\) and \(k_b\) were determined which match real working fluid properties over the compression and expansion strokes, respectively. Values for a stoichiometric mixture appropriate to an SI engine are \(k_u\approx 1.3\), \(k_b\approx 1.2\). However, analysis of pressure-volume data for real engine cycles indicates that \(pV^n\), where \(n\approx 1.3\), is a good fit to the expansion stroke \(p\) -\(V\) data. Heat transfer from the burned gases increases the exponent above the value corresponding to \(k_b\). A value of k\(=1.3\) for the entire cycle is thus a reasonable compromise.

    \(Q^*\) is the enthalpy decrease during isothermal combustion per unit mass of working fluid. Hence:

    \[Q^*=\left(\dfrac{m_f}{m_a}\right)Q_{\mathrm{LHV}}\left(\dfrac{m_a}{m}\right) \nonumber \]

    A simple approximation for \(\left(m_a/m\right)\) is \(\left(r_c-1\right)/r_c\) ; i.e., fresh air fills the displaced volume and the residual gas fills the clearance volume at the same density. Then, for isooctane fuel, for a stoichiometric mixture, \(Q^*\) is given by \(2.92\times {10}^6\left(r_c-1\right)/r_c~\mathrm{J/kg}~\mathrm{air}\). For \(k=1.3\) and an average molecular weight \(M=29.3\), \(c_v=946~\mathrm{J/kg}\cdot \mathrm{K}\). For \(T_1=333~\mathrm{K}\), \(Q^*/\left(c_vT_1\right)\) becomes \(9.3\left(r_c-1\right)/r_c\). For this value of \(Q^*/\left(c_vT_1\right)\) all cycles would be burning a stoichiometric mixture with an appropriate residual gas fraction.

    For all cases \(k=1.3\) and \(Q^*/\left(c_vT_1\right)=9.3\left(r_c-1\right)/r_c\). At any given \(r_c\), the constant-volume cycle has the highest efficiency and lowest \(imep/p_3\). For a given maximum pressure \(p_3\), the constant-pressure cycle has the highest efficiency (and the highest compression ratio). For the limited-pressure cycle, at constant \(p_3/p_1\), there is little improvement in efficiency and \(imep\) above a compression ratio of about 8 to 10 as \(r_c\) is increased.

    FUEL-AIR CYCLE ANALYSIS:

    A more accurate representation of the properties of the working fluid inside the engine cylinder is to treat the unburned mixture as frozen in composition and the burned gas mixture as in equilibrium. Values for thermodynamic properties for these working fluid models can be obtained with the charts for unburned and burned gas mixtures, or the computer codes (EES). When these working fluid models are combined with the ideal engine process models, the resulting cycles are called fuel-air cycles. The sequence of processes and assumptions are (with the notation of Fig. 1):

    1. 1–2: Reversible adiabatic compression of a mixture of air, fuel vapor, and residual gas without change in chemical composition.
    2. 2–3: Complete combustion (at constant volume or limited pressure or constant pressure), without heat loss, to burned gases in chemical equilibrium.
    3. 3–4: Reversible adiabatic expansion of the burned gases which remain in chemical equilibrium.
    4. 4–5–6: Ideal adiabatic exhaust blowdown and displacement processes with the burned gases fixed in chemical composition.
    5. 6–7–1: Ideal intake process with adiabatic mixing between residual gas and fresh mixture, both of which are fixed in chemical composition.

    This page titled 6.2: Thermodynamics Relations for Engine Process was last modified on Wed, 18 Nov 2026 07:22:39 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Haifa El-Sadi.