Opening the book…
Problem#1
Inside an aircraft piston engine cylinder, a turbulent flame front propagates through a compressed mixture of air, Avgas vapor, and residual gas. Just prior to local ignition, the unburned mixture is at a temperature of \(T_u=720~\mathrm{K}\) and a pressure of \(P=18~\mathrm{bar}\). After passing through the flame zone, the local burned gas reaches an equilibrium temperature of \(T_b=2650~\mathrm{K}\). Assuming the mean molecular weight of the unburned gas is \(M_u=29.5~\mathrm{kg/kmol}\) and for the burned gas is \(M_b=28.2~\mathrm{kg/kmol}\) due to high-temperature dissociation, calculate:
- The specific volume ratio (\(v_b/v_u\)) across the flame front.
- The density of the unburned mixture (\(ρ_u\)) and the burned gas mixture (\(ρ_b\)).
Problem#2
An engine inducts a fresh air-fuel charge with a mass-specific enthalpy of \(h_{\mathrm{fresh}}=-150~\mathrm{kJ/kg}\) at \(T_{\mathrm{fresh}}=310~\mathrm{K}\). At the end of the intake stroke, the total charge in the cylinder is mixed with a residual gas fraction of \(x_r=0.07\) (\(7\%\) by mass) remaining in the clearance volume from the previous exhaust stroke. The residual gas has an enthalpy of \(h_r=+680~\mathrm{kJ/kg}\) at \(T_r=950~\mathrm{K}\).
Determine the mass-specific enthalpy of the resulting unburned mixture (\(h_u\)) before compression.
Problem#3
An unburned fuel-air mixture operates at a stoichiometric fuel-air equivalence ratio (\(\phi =1.0\)) and is diluted with a residual burned gas fraction of \(x_b=0.08\) (\(8\%\) residual gases by mass). The mixture is compressed inside an internal combustion chamber to a state corresponding to the end of the compression stroke, defined by:
- Unburned mixture temperature: \(T_1=650~\mathrm{K}\)
- Unburned mixture pressure: \(P_1=1.57~\mathrm{MPa}\)
- Unburned specific internal energy: \(u_{s,u}=300~\mathrm{kJ/kg}~\mathrm{air}\)
- Unburned specific volume: \(v_u=0.13{~\mathrm{m}}^3/\mathrm{kg}~\mathrm{air}\)
Assuming complete adiabatic combustion, calculate the final equilibrium mixture temperature (\(T_2\)) and pressure (\(P_2\)) for two distinct thermodynamic heat addition modes:
- Constant-Volume Adiabatic Combustion at Top Dead Center (Otto Cycle).
- Constant-Pressure Adiabatic Combustion
Problem#4
Utilize a chemical equilibrium calculation program (such as NASA CEA or Cantera) to determine the equilibrium state, thermodynamic properties, and species mole fractions for the following combustion conditions:
Part (a): Equilibrium Product Composition
Plot the variation of specific heat (\(c_p\)), ratio of specific heats (\(γ\)), average molecular weight (\(M\)), and equilibrium species concentrations (\({\mathrm{N}}_2\), \({\mathrm{CO}}_2\), \({\mathrm{H}}_2\mathrm{O}\), \(\mathrm{CO}\), \({\mathrm{H}}_2\), \({\mathrm{O}}_2\), \(\mathrm{OH}\), \(\mathrm{O}\), \(\mathrm{H}\), and \(\mathrm{NO}\)) across equivalence ratios ranging from \(\phi =0.3\) to \(1.5\).
- Fuel: n-Heptane vapor (\({\mathrm{C}}_7{\mathrm{H}}_{16}\)) combusted with air
- Conditions: Constant pressure \(P=35~\mathrm{atm}\) and constant temperature \(T=2400~\mathrm{K}\)
- Plotting Requirement: Display all mole fractions on a single logarithmic vertical axis versus equivalence ratio \(\phi\).
Part (b): Constant Pressure and Constant Volume Combustion
An unburned reactant mixture of n-heptane vapor and air at \(T_1=650~\mathrm{K}\) and \(P_1=15~\mathrm{atm}\) undergoes two separate combustion processes: one at constant pressure and one at constant volume.
- Unburned Mixture Evaluation:
- Calculate the molar enthalpy (\(\overline{h}\)) and molar internal energy (\(\overline{u}\)) of n-heptane vapor at \(650~\mathrm{K}\) in \(\mathrm{cal/gmol}\).
- Calculate the specific volume of the reactant mixture (\(v_{\mathrm{mix}}\)) in \({\mathrm{cm}}^3/\mathrm{g}\) for equivalence ratios \(\phi =0.3,0.5,0.7,0.9,1.1,1.3,1.5\).
- Adiabatic Flame Conditions:
- Using the equilibrium solver, determine the adiabatic flame temperature reached during constant-pressure combustion.
- Determine the peak temperature and peak pressure achieved following constant-volume combustion.
- Plot these resulting temperatures and pressures as a function of \(\phi\).
Reference Data: Thermodynamic Properties of n-Heptane Vapor (\({\mathrm{C}}_7{\mathrm{H}}_{16}\))
| T (K) | cˉp (cal/mol\(\mathrm{\cdot }\) K) | hˉ\(\mathrm{-}\) hˉ298 (kcal/mol) | \(\Delta\) hˉf,298\(\mathrm{\circ }\) (kcal/mol) |
|---|---|---|---|
| 298 | 43.98 | 0.00 | \(-44.89\) |
| 650 | 76.42 | 22.15 | \(-53.12\) |
Problem#5
A gas engine running on a gaseous mixture of butane (\({\mathrm{C}}_4{\mathrm{H}}_{10}\)) and air has the following conditions in the cylinder prior to constant-volume adiabatic combustion:
- Initial Pressure (\(P_1\)): \(93.98~\mathrm{psia}\) (\(6.48\times {10}^5{~\mathrm{N/m}}^2\))
- Initial Temperature (\(T_1\)): \(1080~^{\circ }\mathrm{R}\) (\(600~\mathrm{K}\))
- Charge Composition: Air plus \(50\%\) of the stoichiometric quantity of butane fuel (\(\phi =0.50\)).
Calculate the pressure and temperature at the end of combustion using the data given below.
Thermodynamic Data
1. Reactant Internal Energies (\(\overline{u}\) in \(\mathrm{Btu/lbmol}\)):
| Species | T=536.4 \(\mathrm{\circ }\) R (298 K) | T=1080 \(\mathrm{\circ }\) R (600 K) |
|---|---|---|
| Air | \(2,649~\mathrm{Btu/lbmol}\) | \(5,415~\mathrm{Btu/lbmol}\) |
| Butane (\({\mathrm{C}}_4{\mathrm{H}}_{10}\)) | \(-33.1~\mathrm{Btu/lbmol}\) | \(16,519~\mathrm{Btu/lbmol}\) |
2. Combustion Reaction Data:
- Internal energy of combustion of butane at \(536.4~^{\circ }\mathrm{R}\) (\(298~\mathrm{K}\)):
3. Product Internal Energies (\(\overline{u}\) per lbmol of products at \(\phi =0.50\)):
| Temperature T (\(\mathrm{\circ }\) R) | uˉ (Btu/lbmol) |
|---|---|
| \(536.4~^{\circ }\mathrm{R}\) | \(2,705.7~\mathrm{Btu/lbmol}\) |
| \(3735.0~^{\circ }\mathrm{R}\) | \(23,313.4~\mathrm{Btu/lbmol}\) |
| \(3744.0~^{\circ }\mathrm{R}\) | \(23,379.2~\mathrm{Btu/lbmol}\) |
Problem#6
For \(k=1.3\), compression ratio \(r_c=6\), and a stoichiometric mixture with intake temperature \(300~\mathrm{K}\), find the residual gas fraction, residual gas temperature, and mixture temperature at point 1 in the constant-volume cycle for \(p_e/p_i=1\) (unthrottled operation) and \(2\) (throttled operation).
For a stoichiometric mixture, for isooctane:
\[Q^*=\dfrac{m_f}{m}Q_{\mathrm{LHV}}=\left(\dfrac{m_f}{m_i}\right)\left(\dfrac{m_i}{m}\right)Q_{\mathrm{LHV}}=\dfrac{44.38}{16.14}\left(1-x_r\right)=2.75\left(1-x_r\right)~\mathrm{MJ/kg} \nonumber \]
For \(k=1.3\), \(c_v=946~\mathrm{J/kg}\cdot \mathrm{K}\) and
\[\dfrac{Q^*}{c_vT_1}=\dfrac{2.75\times {10}^6}{946T_1}\left(1-x_r\right)=\dfrac{2910}{T_1}\left(1-x_r\right) \nonumber \]
For \(r_c=6\) and \(k=1.3\), become:
\[x_r=\dfrac{1}{6}\dfrac
Callstack:
at (Bookshelves/Aerospace_Engineering/Aircraft_Engine:_Design_and_Analysis/06:_Combustor-_Working_Fluid_and_Models_of_Engine_Cycles/6.04:_Problems_and_References), /content/body/div[6]/p[7]/span[1], line 1, column 1
Callstack:
at (Bookshelves/Aerospace_Engineering/Aircraft_Engine:_Design_and_Analysis/06:_Combustor-_Working_Fluid_and_Models_of_Engine_Cycles/6.04:_Problems_and_References), /content/body/div[6]/p[7]/span[2], line 1, column 1
\[\dfrac{T_r}{T_1}={\left(\dfrac{p_e}{p_i}\right)}^{0.23}{\left(1+\dfrac{Q^*}{c_vT_1\times 6^{0.3}}\right)}^{0.769} \nonumber \]
\[\dfrac{T_1}{300}=\dfrac{1-x_r}{1-\left[1/\left(1.3\times 6\right)\right]\left(p_e/p_i+0.3\right)} \nonumber \]
A trial-and-error solution is required. It is easiest to estimate \(x_r\), solve for \(T_1\) from (d), evaluate \(Q^*/\left(c_vT_1\right)\) from (a), and check the value of \(x_r\) assumed with that given by (b).
For \(\left(p_e/p_i\right)=1\) (unthrottled operation):
\[x_r=0.044,\qquad T_1=344~\mathrm{K},\qquad \dfrac{Q^*}{c_vT_1}=8.1,\qquad T_r=1316~\mathrm{K} \nonumber \]
For \(\left(p_e/p_i\right)=2\) (throttled operation):
\[x_r=0.082,\qquad T_1=391~\mathrm{K},\qquad \dfrac{Q^*}{c_vT_1}=6.8,\qquad T_r=1580~\mathrm{K} \nonumber \]
Problem#7
Calculate the performance characteristics of the constant-volume fuel-air cycle. The compression ratio is 8; the fuel is isooctane and the mixture is stoichiometric; the pressure and temperature inside the cylinder at the start of compression are \(1~\mathrm{atm}\) and \(350~\mathrm{K}\), respectively. Use the notation of Fig. 1 to define the states at the beginning and end of each process.
The compression process:
\[T_1=350~\mathrm{K},\qquad p_1=101.3~\mathrm{kPa},\qquad v_1=1{~\mathrm{m}}^3\mathrm{/kg}~\mathrm{air},\qquad u_{s1}=40~\mathrm{kJ/kg}~\mathrm{air} \nonumber \]
\[T_2=682~\mathrm{K},\qquad p_2=1.57~\mathrm{MPa},\qquad v_2=0.125{~\mathrm{m}}^3\mathrm{/kg}~\mathrm{air},\qquad u_{s2}=350~\mathrm{kJ/kg}~\mathrm{air} \nonumber \]
\[W_{1-2}=W_C=-310~\mathrm{kJ/kg}~\mathrm{air} \nonumber \]
The constant-volume adiabatic combustion process (it was assumed that the residual gas fraction was 0.08):
\[u_{b3}=u_{s2}+Δu^{\circ }_{f,u}=-5~\mathrm{kJ/kg}~\mathrm{air},\qquad s_3=9.33~\mathrm{kJ/kg}~\mathrm{air}\cdot \mathrm{K} \nonumber \]
\[v_3=v_2=0.125{~\mathrm{m}}^3\mathrm{/kg}~\mathrm{air},\qquad T_3=2825~\mathrm{K},\qquad p_3=7100~\mathrm{kPa} \nonumber \]
\[T_4=1840~\mathrm{K},\qquad p_4=570~\mathrm{kPa},\qquad u_4=-1540~\mathrm{kJ/kg}~\mathrm{air} \nonumber \]
\[W_{3-4}=W_E=1535~\mathrm{kJ/kg}~\mathrm{air} \nonumber \]
Problem#8
It is desired to increase the output of a spark-ignition engine by either [GrindEQ__1_] raising the compression ratio from \(8\) to \(10\) or [GrindEQ__2_] increasing the inlet pressure from \(1.0~\mathrm{atm}\) to \(1.5~\mathrm{atm}\). Using the constant-volume cycle as a model for engine operation, which procedure will give:
- The highest pressure of the cycle?
- The highest efficiency?
- The highest mep?
Assume \(k=1.3\) and \(\left(m_fQ_{\mathrm{HV}}\right)/\left(mc_vT_1\right)=9.3\left(r_c-1\right)/r_c\).
Problem#9
A spark-ignition engine is throttled when operating at part load (the inlet pressure is reduced) while the fuel/air ratio is held essentially constant. The inlet air is at pressure \(p_1\), the exhaust pressure is atmospheric \(p_a\), and the ambient temperature is \(T_a\). Derive an expression for the decrease in net indicated fuel conversion efficiency due to throttling from the ideal constant-volume cycle efficiency and show that it is proportional to \(\left(p_a/p_1-1\right)\). Assume mass fuel \(\ll\) mass air.
References
J. B. Heywood, Internal Combustion Engine Fundamentals. New York, NY, USA: McGraw-Hill, 1988.
Charles Fayette Taylor, The Internal Combustion Engine in Theory and Practice (Volumes 1 & 2), MIT Press
This page titled 6.3: Problems and References was last modified on Wed, 18 Nov 2026 07:22:39 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by .
The book could not be loaded just now.