Opening the book…
In internal combustion engines, the working fluid is not a static, idealized medium, but rather a dynamic thermodynamic substance whose chemical composition, phase, and physical properties evolve continuously throughout the engine cycle. This transformation begins during the intake stroke, where the fresh unburned mixture is drawn into the cylinder, mixed with residual combustion gases, and subjected to complex phase-change and thermodynamic interactions. Before entering the cylinder, ambient air is mixed with fuel in the induction system via a carburetor, port fuel injector, or direct cylinder injector. The fresh charge consists primarily of standard atmospheric air and vaporized or atomized hydrocarbon fuel.
In gas turbine engines (turbofans, turbojets, and turboprops), the working fluid flows continuously through the engine, undergoing continuous changes in temperature, pressure, phase, chemical composition, and thermodynamic properties as it moves from the ambient air intake to the exhaust nozzle. Unlike piston engines—where fuel is mixed with air during or prior to the intake stroke—a gas turbine inducts and compresses pure atmospheric air before any fuel is introduced. In an aircraft piston engine, the working fluid undergoes a complete chemical and thermodynamic conversion across the four distinct strokes of the cycle. Unlike gas turbine engines, which compress pure air and burn lean in a continuous flow, the aircraft piston engine processes discrete batches of a near-stoichiometric fuel-air mixture that reacts periodically under high pressure and temperature.
Aircraft piston engines and gas turbine engines differ fundamentally in their operational, thermodynamic, and physical characteristics. In a piston engine, fuel is inducted or injected before combustion and burned in an intermittent batch process following the constant-volume Otto cycle near a stoichiometric equivalence ratio (\(\phi \approx 0.9-1.1\)), relying on a mechanical volume compression ratio typically restricted to \(7:1-9:1\). In contrast, gas turbine engines inject fuel directly after full compression, operating as a continuous, steady-flow process under the constant-pressure Brayton cycle; they function with a highly lean overall equivalence ratio (\(\phi \approx 0.2-0.4\)) and achieve significantly higher-pressure compression ratios ranging from \(15:1\) to over \(40:1\). Consequently, while the specific heat ratio (\(\gamma\)) of the expanded exhaust gas in a piston engine drops to approximately \(1.25-1.28\) due to rich triatomic combustion products at high temperatures, the excess air in a gas turbine yields a slightly higher expanded gas \(\gamma\) of approximately \(1.30-1.33\).
The ideal working fluid for both engines is evaluated using air-standard cycle models, but their governing compression mechanisms and heat addition processes differ fundamentally:
- Piston Engine (Constant-Volume Otto Cycle): Heat addition occurs instantaneously at Top Dead Center (TDC) under constant volume (\(V=\mathrm{constant}\)). Thermal efficiency (\({\eta }_{\mathrm{Otto}}\)) is governed by the volumetric compression ratio \(r=V_{\mathrm{max}}/V_{\mathrm{min}}\):
- Gas Turbine Engine (Constant-Pressure Brayton Cycle): Heat addition occurs continuously at constant pressure (\(P=\mathrm{constant}\)). Thermal efficiency (\({\eta }_{\mathrm{Brayton}}\)) is governed by the pressure compression ratio \(r_p=P_2/P_1\):
The equivalence Ratio (\(\boldsymbol{\phi }\)) & Mass Fuel-Air Ratio
The chemical composition of the working fluid during and after combustion is dictated by the equivalence ratio (\(\phi\)), defined as:
\[\phi =\d \dfrac{\left(F/A\right)}_{\mathrm{actual}}{\left(F/A\right)_{\mathrm{stoichiometric}}} \nonumber \]
- Piston Engine (\(\phi \approx 0.9-1.1\) ): Operates near stoichiometric conditions (\(F/A\approx 0.067\)). The working fluid transitions entirely into combustion products:
- Gas Turbine Engine (\(\phi \approx 0.2-0.4\) ): Operates highly lean overall (\(F/A\approx 0.015-0.025\)) to restrict turbine inlet temperatures (\(T_4\)). Consequently, the hot working fluid is a mixture of combustion products heavily diluted by unreacted excess air:
This page titled 6.0: Working Fluid Dynamics was last modified on Wed, 18 Nov 2026 07:18:34 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by .
The book could not be loaded just now.