Opening the book…
An ideal turbojet engine comprising the inlet, gas generator, and nozzle as shown in Figure 7) is thermodynamically equivalent to an ideal Brayton cycle. The classical Brayton cycle thermal efficiency (\(η_{\mathrm{th}}\)) is expressed as:
\[η_{\mathrm{th}}=1-\dfrac{T_0}{T_3} \nonumber \]
where \(T_3\) is the compressor discharges static temperature and \(0\) denotes ambient intake conditions.
Recasting the thermal efficiency in terms of the compressor temperature ratio (\(τ_c\equiv T_{t3}/T_{t2}\)), ram temperature ratio (\(τ_r\equiv T_{t2}/T_0\)), and compressor pressure ratio (\(π_c\equiv p_{t3}/p_{t2}\)):
\[η_{\mathrm{th}}=1-\dfrac{1}{\dfrac{T_3}{T_0}}=1-\dfrac{1}{\left(\dfrac{T_{t3}}{T_{t2}}\right)\left(\dfrac{T_{t2}}{T_0}\right)}=1-\dfrac{1}{τ_cτ_r}=1-\dfrac{1}{π^{\dfrac{k-1}{k}}_c\left(1+\dfrac{k-1}{2}{Ma}^2_0\right)} \nonumber \]
For a fixed flight Mach number (\({Ma}_0\)), the ram temperature ratio (\(τ_r\)) remains constant. Consequently, increasing the compressor pressure ratio (\(π_c\)) directly elevates thermal efficiency (\(η_{\mathrm{th}}\)). While a higher \(π_c\) improves thermal performance, the resulting elevated compressor discharge temperature (\(T_{t3}\)) introduces severe structural and aerodynamic challenges for the high-pressure compressor (HPC). The advanced material requirements is standard titanium alloys reach thermal limits at high exit temperatures, forcing the use of nickel-based superalloys typically reserved for the turbine section. The active HPC cooling is extreme discharge temperatures may require active cooling schemes for the final compressor stages, such as regenerative fuel-cooling loops. The secondary flow & tip clearance losses are higher gas compression decreases fluid density, resulting in tiny blade heights and extremely narrow annular flow passages. Boundary layer displacement thickness and tip clearances consume a larger percentage of the flow path, significantly driving up secondary flow losses.
The relationship between flight Mach number, compressor pressure ratio, and cycle thermal efficiency is given by:
\[η_{\mathrm{th}}=1-\dfrac{1}{π^{\dfrac{k-1}{k}}_c\left(1+\dfrac{k-1}{2}{Ma}^2_0\right)} \nonumber \]
For a fixed compressor pressure ratio (\(π_c\)), cycle thermal efficiency increases directly with flight Mach number (\({Ma}_0\)). Higher flight speeds elevate the inlet total stagnation temperature (\(T_{t2}\)) via ram compression. When multiplied by a constant compressor pressure ratio (\(π_c\)), the overall compressor discharge temperature (\(T_{t3}\)) increases, raising the baseline thermodynamic efficiency of the cycle. Because \({Ma}_0\approx 0\) during static takeoff, an engine operates at its lowest thermal efficiency at the start of flight. While thermal efficiency improves at higher airspeeds, flight Mach number is determined by aircraft mission profile requirements rather than an engine optimization variable.
Propulsive efficiency (\(η_p\)) measures how effectively the kinetic power produced by an engine is converted into useful propulsive power delivered to the aircraft:
\[η_p\equiv \dfrac{\mathrm{Thrust}~\mathrm{Power}}{Δ\mathrm{Kinetic}~\mathrm{Energy}~\mathrm{Rate}}=\dfrac{F\cdot V_0}
Callstack:
at (Bookshelves/Aerospace_Engineering/Aircraft_Engine:_Design_and_Analysis/04:_Aircraft_Engine-_Gas_Turbine_Engine/4.04:_Turbojet), /content/body/p[11]/span, line 1, column 1
To evaluate thrust power (\(F\cdot V_0\)), uninstalled or installed thrust values can be used. Calculating installed thrust is significantly more complex due to throttle-dependent inlet/exhaust drag and airframe integration effects.
To simplify analysis, uninstalled net thrust (\(F_{n,\mathrm{uninstalled}}\)) is expressed in general form as:
\[F_{n,\mathrm{uninstalled}}={\dot{m}}_9V_9-{\dot{m}}_0V_0+\left(p_9-p_0\right)A_9 \nonumber \]
Assuming a perfectly expanded nozzle (\(p_9=p_0\)), the pressure thrust term vanishes. Further neglecting fuel mass contribution (\({\dot{m}}_f\ll {\dot{m}}_0\Longrightarrow {\dot{m}}_9\approx {\dot{m}}_0\)), uninstalled net thrust simplifies to:
\[F_{n,\mathrm{uninstalled}}\approx {\dot{m}}_0\left(V_9-V_0\right) \nonumber \]
Real engine components suffer from viscous losses, shocks, heat transfer, and mechanical friction rather than ideal isentropic behavior. At high supersonic speeds (e.g., \({Ma}_0\ge 3\)), external ram compression inside the inlet generates sufficient pressure rise on its own, eliminating the need for a mechanical compressor. Neglecting fuel mass addition (\({\dot{m}}_f\ll {\dot{m}}_a\)), the net specific work output (\(w_c\)) of an ideal turbojet cycle is defined by the difference between total fluid expansion and compression:
\[w_c\approx \left(h_{t4}-h_9\right)-\left(h_{t3}-h_0\right) \nonumber \]
\(\left(h_{t4}-h_9\right)\) is specific work produced across the expansion leg (turbine and exhaust nozzle). \(\left(h_{t3}-h_0\right)\) is specific work absorbed across the compression leg (inlet dynamic compression and compressor stage work).
Having determined the fuel-to-air ratio (\(f\)), exit velocity (\(V_9\)), ambient velocity (\(V_0\)), and exit static temperature (\(T_9\)), the specific thrust (\(F_n/{\dot{m}}_0\)) is expressed as:
\[\dfrac{F_n}{{\dot{m}}_0}=\left(1+f\right)V_9-V_0+\dfrac{RT_9\left(1+f\right)}{V_9}\left(1-\dfrac{p_0}{p_9}\right) \nonumber \]
The momentum terms \(\left(1+f\right)V_9-V_0\) provide the dominant contribution to specific thrust in an air-breathing engine. The pressure thrust term drops to zero under perfect expansion (\(p_9=p_0\)) and remains small relative to the momentum component during off-design operation.
Multiplying the numerator and denominator of the pressure term by \(γ\), and substituting \(a^2_9=kRT_9\) and \(M^2_9=V^2_9/a^2_9\), recasts the specific thrust into a more compact form:
\[\dfrac{F_n}{{\dot{m}}_0}=\left(1+f\right)V_9\left[1+\dfrac{1}{γM^2_9}\left(1-\dfrac{p_0}{p_9}\right)\right]-V_0 \nonumber \]
Thrust Specific Fuel Consumption (TSFC) defines the fuel mass flow rate required per unit of net thrust generated:
\[\mathrm{TSFC}\equiv \dfrac{{\dot{m}}_f}{F_n}=\dfrac{f}{F_n/{\dot{m}}_0} \nonumber \]
Combining the specific thrust and fuel-to-air ratio allows the engine’s overall efficiency (\(η_o\)) to be expressed as a function of \(\mathrm{TSFC}\):
\[η_o=\dfrac{\left(F_n/{\dot{m}}_0\right)V_0}{fQ_R}=\dfrac{V_0/Q_R}{\mathrm{TSFC}} \nonumber \]
where \(Q_R\) is the lower heating value of the fuel. This relationship demonstrates that overall engine efficiency is inversely proportional to specific fuel consumption:
\[η_o\propto \dfrac{1}{\mathrm{TSFC}} \nonumber \]
Lowering the engine’s \(\mathrm{TSFC}\) directly yields a higher overall thermodynamic and propulsive efficiency.
4.3.1 Turbojet Engine with Afterburner
To augment the net thrust of an aircraft gas turbine engine, an afterburner (or reheat system) can be integrated into the exhaust duct section as indicated in Figure 8. Widely utilized in military aircraft, this system offers an exceptionally simple and reliable mechanical solution for short-duration power boosts.
The mass flow rate (\(\dot{m}\)) through a choked orifice is governed by the compressible flow continuity relation:
\[\dot{m}=\sqrt{\dfrac{k}{R}}\cdot \dfrac{p_t}{\sqrt{T_t}}\cdot A\cdot Ma{\left(1+\dfrac{k-1}{2}{Ma}^2\right)}^{-\dfrac{k+1}{2\left(k-1\right)}} \nonumber \]
Mass Flow Rate (\(\dot{m}\)) increases slightly due to auxiliary fuel addition (\({\dot{m}}_{f,\mathrm{AB}}\)), roughly \(3--4\%\), and total pressure (\(p_t\)) drops slightly across the burner due to combustion losses, roughly \(5--8\%\).
Because \(\dot{m}\), \(p_t\), and gas properties undergo only minor fractional shifts, the required nozzle throat area (\(A_8\)) is predominantly driven by the total temperature (\(T_t\)). To prevent upstream pressure back-propagation, the variable-geometry throat (\(A_8\)) must open in direct proportion to the square root of the gas total temperature:
\[\dfrac{A_{8,\mathrm{AB-ON}}}{A_{8,\mathrm{AB-OFF}}}\approx \sqrt{\dfrac{T_{t8,\mathrm{AB-ON}}}{T_{t8,\mathrm{AB-OFF}}}} \nonumber \]
An afterburner duct incorporates major structural systems to enable stable combustion, inlet diffuser decelerates incoming turbine exhaust gas to lower dynamic pressure, improving combustion efficiency and flame stability.
The addition of an afterburner modifies the inlet conditions to the exhaust nozzle in terms of mass flow rate, total pressure, and total temperature. The auxiliary fuel mass flow rate (\({\dot{m}}_{f,\mathrm{AB}}\)) increases total mass flow, while combustion losses reduce total pressure (\(p_{t7}\)). The exit total temperature (\(T_{t7}\)) is bounded by thermal material limits. Consequently, nozzle expansion analysis follows standard compressible flow principles, using updated nozzle entry states.
The fundamental definitions for thermal efficiency (\(η_{\mathrm{th}}\)) and propulsive efficiency (\(η_p\)) apply to afterburning turbojets, incorporating the additional heat energy input (\({\dot{m}}_{f,\mathrm{AB}}Q_{R,\mathrm{AB}}\)):
\[η_{\mathrm{th}}\equiv \dfrac{Δ\dot{\mathrm{K}}\mathrm{E}}
Callstack:
at (Bookshelves/Aerospace_Engineering/Aircraft_Engine:_Design_and_Analysis/04:_Aircraft_Engine-_Gas_Turbine_Engine/4.04:_Turbojet), /content/body/p[42]/span[1], line 1, column 1
Callstack:
at (Bookshelves/Aerospace_Engineering/Aircraft_Engine:_Design_and_Analysis/04:_Aircraft_Engine-_Gas_Turbine_Engine/4.04:_Turbojet), /content/body/p[42]/span[2], line 1, column 1
\[η_{\mathrm{th}}=\dfrac{\left({\dot{m}}_0+{\dot{m}}_f+{\dot{m}}_{f,\mathrm{AB}}\right)\dfrac{V^2_9}{2}-{\dot{m}}_0\dfrac{V^2_0}{2}}
Callstack:
at (Bookshelves/Aerospace_Engineering/Aircraft_Engine:_Design_and_Analysis/04:_Aircraft_Engine-_Gas_Turbine_Engine/4.04:_Turbojet), /content/body/p[43]/span, line 1, column 1
The Propulsive Efficiency (\(η_p\))
\[η_p\equiv \dfrac{F\cdot V_0}{Δ\dot{\mathrm{K}}\mathrm{E}}=\dfrac{\left(\dfrac{F_n}
Callstack:
at (Bookshelves/Aerospace_Engineering/Aircraft_Engine:_Design_and_Analysis/04:_Aircraft_Engine-_Gas_Turbine_Engine/4.04:_Turbojet), /content/body/p[45]/span, line 1, column 1
where \(f\equiv \dfrac
Callstack:
at (Bookshelves/Aerospace_Engineering/Aircraft_Engine:_Design_and_Analysis/04:_Aircraft_Engine-_Gas_Turbine_Engine/4.04:_Turbojet), /content/body/p[46]/span[1], line 1, column 1
Callstack:
at (Bookshelves/Aerospace_Engineering/Aircraft_Engine:_Design_and_Analysis/04:_Aircraft_Engine-_Gas_Turbine_Engine/4.04:_Turbojet), /content/body/p[46]/span[2], line 1, column 1
The total pressure ratio chain for an afterburning engine includes the pressure drop across the afterburner duct (\(π_{\mathrm{AB}}\equiv p_{t7}/p_{t6}\)).
Standard Turbojet Nozzle Pressure Ratio (\(π_n\)):
\[π_n={\left\
Callstack:
at (Bookshelves/Aerospace_Engineering/Aircraft_Engine:_Design_and_Analysis/04:_Aircraft_Engine-_Gas_Turbine_Engine/4.04:_Turbojet), /content/body/p[49]/span, line 1, column 1
Afterburning Turbojet (AB-TJ) Nozzle Pressure Ratio (\(π_n\)):
\[π_n={\left\
Callstack:
at (Bookshelves/Aerospace_Engineering/Aircraft_Engine:_Design_and_Analysis/04:_Aircraft_Engine-_Gas_Turbine_Engine/4.04:_Turbojet), /content/body/p[51]/span, line 1, column 1
By incorporating the afterburner total pressure ratio (\(π_{\mathrm{AB}}\equiv p_{t7}/p_{t6}\)) into the expansion chain, the nozzle exit Mach number (\(M_9\)) for an afterburning turbojet (AB-TJ) is expressed as:
\[M_9=\sqrt{\dfrac{2}{γ-1}\left[{\left(π_nπ_{\mathrm{AB}}π_tπ_bπ_cπ_dπ_r\dfrac{p_0}{p_9}\right)}^{\dfrac{k-1}{k}}-1\right]} \nonumber \]
The corresponding exhaust exit velocity (\(V_9\)) is calculated using the exit Mach number and speed of sound (\(a_9\)), expressed in terms of the ambient speed of sound (\(a_0=\sqrt{kRT_0}\)) and the burner temperature parameter (\(τ_{λ,\mathrm{AB}}\equiv T_{t7}/T_0\)):
\[V_9={Ma}_9a_9={Ma}_9\sqrt{\dfrac{kRT_{t9}}{1+\dfrac{k-1}{2}{Ma}^2_9}}={Ma}_9\sqrt{\dfrac{kRT_0τ_{λ,\mathrm{AB}}}{1+\dfrac{k-1}{2}{Ma}^2_9}}=a_0{Ma}_9\sqrt{\dfrac{τ_{λ,\mathrm{AB}}}{1+\dfrac{k-1}{2}{Ma}^2_9}} \nonumber \]
Accounting for both primary combustor fuel (\(f\)) and afterburner fuel (\(f_{\mathrm{AB}}\)), the specific thrust (\(F_n/{\dot{m}}_0\)) for an afterburning turbojet is derived as:
\[\dfrac{F_n}{{\dot{m}}_0}=\dfrac{\left({\dot{m}}_0+{\dot{m}}_f+{\dot{m}}_{f,\mathrm{AB}}\right)V_9-{\dot{m}}_0V_0+\left(p_9-p_0\right)A_9}{{\dot{m}}_0} \nonumber \]
Substituting \({\dot{m}}_9=ρ_9V_9A_9\) and the ideal gas relation (\(a^2_9=kRT_9\)) converts the pressure thrust component into nondimensional Mach form:
\[\dfrac{F_n}
Callstack:
at (Bookshelves/Aerospace_Engineering/Aircraft_Engine:_Design_and_Analysis/04:_Aircraft_Engine-_Gas_Turbine_Engine/4.04:_Turbojet), /content/body/p[59]/span, line 1, column 1
\[\dfrac{F_n}
Callstack:
at (Bookshelves/Aerospace_Engineering/Aircraft_Engine:_Design_and_Analysis/04:_Aircraft_Engine-_Gas_Turbine_Engine/4.04:_Turbojet), /content/body/p[60]/span, line 1, column 1
\[\dfrac{F_n}
Callstack:
at (Bookshelves/Aerospace_Engineering/Aircraft_Engine:_Design_and_Analysis/04:_Aircraft_Engine-_Gas_Turbine_Engine/4.04:_Turbojet), /content/body/p[61]/span, line 1, column 1
The Thrust Specific Fuel Consumption (\(\mathrm{TSFC}\)) accounts for the total fuel input across both combustion zones:
\[\mathrm{TSFC}\equiv \dfrac
Callstack:
at (Bookshelves/Aerospace_Engineering/Aircraft_Engine:_Design_and_Analysis/04:_Aircraft_Engine-_Gas_Turbine_Engine/4.04:_Turbojet), /content/body/p[63]/span, line 1, column 1
Multiplying specific thrust by average velocity [\(\dfrac{1}{2}\left(V_0+V_9\right)\) ] yields the net specific work output (\(w_c\)) of the cycle:
\[w_c\approx \dfrac{V^2_9}{2}-\dfrac{V^2_0}{2} \nonumber \]
For a given flight speed (\(V_0\)), maximizing specific cycle work requires maximizing exhaust kinetic energy (\(\dfrac{1}{2}V^2_9\)). The kinetic energy is governed by the total-to-static enthalpy drop across the exhaust nozzle:
\[\dfrac{V^2_9}{2}\equiv h_{t9}-h_9=h_{t9}\left(1-\dfrac{T_9}{T_{t9}}\right)=h_0τ_{λ,\mathrm{AB}}\left[1-\dfrac{1}{1+\dfrac{k-1}{2}{Ma}^2_9}\right] \nonumber \]
where \(τ_{λ,\mathrm{AB}}\equiv T_{t7}/T_0\).
For a fixed burner temperature parameter (\(τ_{λ,\mathrm{AB}}\)) and ambient enthalpy (\(h_0\)), maximizing exit kinetic energy depends directly on maximizing the exit Mach number (\({Ma}_9\)):
\[{Ma}^2_9=\dfrac{2}{k-1}\left[{\left(\dfrac{p_{t9}}{p_9}\right)}^{\dfrac{k-1}{k}}-1\right] \nonumber \]
Maximizing \({Ma}_9\) requires maximizing the exit total-to-static pressure ratio (\(p_{t9}/p_9\)), expanded through the full component total pressure ratio chain:
\[\dfrac{p_{t9}}{p_9}=\left(\dfrac{p_{t9}}{p_{t7}}\right)\left(\dfrac{p_{t7}}{p_{t5}}\right)\left(\dfrac{p_{t5}}{p_{t4}}\right)\left(\dfrac{p_{t4}}{p_{t3}}\right)\left(\dfrac{p_{t3}}{p_{t2}}\right)\left(\dfrac{p_{t2}}{p_{t0}}\right)\left(\dfrac{p_{t0}}{p_0}\right)\left(\dfrac{p_0}{p_9}\right) \nonumber \]
\[\dfrac{p_{t9}}{p_9}=π_nπ_{\mathrm{AB}}π_tπ_bπ_cπ_dπ_r\left(\dfrac{p_0}{p_9}\right) \nonumber \]
Assuming ideal components (\(π_n=π_{\mathrm{AB}}=π_b=π_d=1.0\)), perfect expansion (\(p_9=p_0\)), and substituting the ideal turbine temperature ratio (\(τ_t=1-\dfrac{τ_r\left(τ_c-1\right)}{τ_λ}\)), the pressure ratio expression reduces to:
\[\dfrac{p_{t9}}{p_9}=1\cdot 1\cdot τ^{\dfrac{k}{k-1}}_t\cdot 1\cdot τ^{\dfrac{k}{k-1}}_c\cdot 1\cdot τ^{\dfrac{k}{k-1}}_r\cdot 1\cdot 1={\left[τ_rτ_c\left(1-\dfrac{τ_r\left(τ_c-1\right)}{τ_λ}\right)\right]}^{\dfrac{k}{k-1}} \nonumber \]
This page titled 4.3: Turbojet was last modified on Wed, 18 Nov 2026 07:22:37 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by .
The book could not be loaded just now.