5.4: Problems and References

Aircraft Engine: Design and Analysis · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    5.4: Problems and References

    Problem 1

    1. The engine intake decelerates the airflow during cruise. The axial flow entering the fan has an axial Mach number of \(M_{a1}=0.50\). Assuming this value, determine the static temperature (\(T_1\)) and the speed of sound (\(a_1\)) at the fan inlet when the aircraft is cruising at \(M_{\infty }=0.82\) at an altitude of \(36,000~\mathrm{ft}\) (where ambient static temperature \(T_{\infty }=216.65~\mathrm{K}\), \(γ=1.4\), and \(R=287~\mathrm{J/(kg}\cdot \mathrm{K)}\)).
    2. The engine total mass flow rate at cruise is \({\dot{m}}_{\mathrm{total}}=400~\mathrm{kg/s}\) with a bypass ratio \(B=10.0\) (so core mass flow rate \({\dot{m}}_{\mathrm{core}}=36.36~\mathrm{kg/s}\)). With a fan pressure ratio of \(1.6\), the required fan outer tip diameter is \(D_{\mathrm{tip}}=2.80~\mathrm{m}\) (tip radius \(r_t=1.40~\mathrm{m}\)). Assuming a relative tip Mach number of \(M_{\mathrm{a}}=1.35\), calculate the blade tip velocity (\(U_t\)) and the rotational speed of the fan (\(Ω_{\mathrm{LP}}\) in \(\mathrm{rad/s}\)). (Note: \(V_{\mathrm{rel,\ tip}}=\sqrt{U^2_t+V^2_x}\)).
    3. The average stagnation pressure ratio across the fan rotor for the core stream is \(π_f=1.50\), with an isentropic efficiency of \(η_f=0.88\). Find the total (stagnation) pressure (\(P_{02}\)) and total (stagnation) temperature (\(T_{02}\)) entering the booster (LP compressor).

    Problem 2

    1. The hub radius increases through the fan and stator downstream of the fan. At the booster inlet, the hub radius \(r_h\) and tip radius \(r_t\) are \(0.48\) and \(0.56\) times the tip radius of the fan (\(r_{\mathrm{fan,\ tip}}=1.40~\mathrm{m}\)), making the mean radius of the booster \(r_m=0.52\cdot r_{\mathrm{fan,\ tip}}=0.728~\mathrm{m}\). This means radius is constant from inlet to exit. The stators after the fan leave the flow direction at mid-radius inclined at \({25}^{\circ }\) from axial. The effective flow area at booster inlet is \(π\left(r^2_t-r^2_h\right){\mathrm{cos} \left({25}^{\circ }\right)\ }\). The core mass flow rate is \({\dot{m}}_{\mathrm{core}}=35.0~\mathrm{kg/s}\). The stagnation properties entering the booster are \(T_{02}=280.11~\mathrm{K}\) and \(P_{02}=52.98~\mathrm{kPa}\), yielding a speed of sound at mid-span of \(a\approx 320~\mathrm{m/s}\). The axial Mach number is approximately \(M_x\approx 0.42\). Find the resultant velocity \(V\) at mid-span, the axial velocity \(V_x\), and the ratio of axial velocity to mean blade speed (\(V_x/U_m\)) for the booster, assuming \(Ω_{\mathrm{LP}}=274.67~\mathrm{rad/s}\).
    2. Find the stagnation temperature (\(T_{03}\)) and pressure (\(P_{03}\)) at the outlet of the booster if the overall pressure ratio across the fan and booster combined is \(2.8\) and the overall efficiency is \(88\%\). Assuming the axial velocity \(V_x\) remains constant through the booster, find the static temperature (\(T_3\)), static pressure (\(P_3\)), and air density (\(ρ_3\)) at the booster exit. Hence, calculate the flow area at the exit (\(A_{\mathrm{exit}}\)) and the corresponding exit blade height (\(h\)) where \(A_{\mathrm{exit}}\approx 2πr_mh\).
    3. The pressure ratio across the fan for core flow is \(1.5\), so the required pressure ratio across the booster alone is \(π_b=2.8/1.5=1.867\). The stage loading coefficient \(ψ=Δh_0/U^2_m\) for the booster is not to exceed \(0.38\). Find the minimum number of stages required and the resulting value of the stage loading coefficient, assuming it is equal across all stages.

    Problem 3

    1. The fan and LP compressor (booster) combined provide a total pressure ratio of \(2.8\) to the core stream entering the HP compressor, with an overall efficiency of \(88\%\). The flow at entry to the HP compressor is purely axial with a velocity of \(V_x=160~\mathrm{m/s}\). The inlet ambient total temperature is \(T_{01}=245.8~\mathrm{K}\) and total pressure is \(P_{01}=35.32~\mathrm{kPa}\). Find the static temperature (\(T_{21}\)), static pressure (\(P_{21}\)), air density (\(ρ_{21}\)), and Mach number (\({Ma}_{21}\)) at HP compressor entry. Supposing the hub-to-tip radius ratio at entry is \(r_h/r_t=0.65\) and the core mass flow rate is \({\dot{m}}_{\mathrm{core}}=35.0~\mathrm{kg/s}\), find the mean radius (\(r_m\)), tip radius (\(r_t\)), and hub radius (\(r_h\)).
    2. Throughout the HP compressor, \(V_x/U_m=0.50\), where \(U_m\) is the mid-span blade speed. For the first stage, the hub radius is \(0.65\) times the tip radius (\(r_h=0.65r_t\)). Assuming the relative Mach number at the first stage tip is \(\mathrm{Ma}=1.25\), find the relative velocity (\(V_{\mathrm{rel,\ tip}}\)), tip speed (\(U_t\)), rotational speed of the HP shaft (\(Ω_{\mathrm{HP}}\) in rev/s), and the actual axial velocity (\(V_x\)).

    Problem 4

    1. At the HP compressor exit, the flow is purely axial and the mean radius is constant at \(r_m=0.30~\mathrm{m}\). The HP compressor operates with a pressure ratio of \(Π_{\mathrm{HP}}=15.0\) and an isentropic efficiency of \(η_{\mathrm{HP}}=0.88\). The stagnation conditions entering the HP compressor are \(T_{021}=330~\mathrm{K}\) and \(P_{021}=90.0~\mathrm{kPa}\), and the axial velocity is held constant at \(V_x=165~\mathrm{m/s}\) throughout. For a core mass flow rate of \({\dot{m}}_{\mathrm{core}}=32.0~\mathrm{kg/s}\), determine the static temperature (\(T_3\)), static pressure (\(P_3\)), and air density (\(ρ_3\)) at the compressor exit. From these, calculate the required exit cross-sectional area (\(A_{\mathrm{exit}}\)) and the corresponding exit blade height (\(h\)), assuming \(A_{\mathrm{exit}}\approx 2πr_mh\).
    2. If the stage loading coefficient for the HP compressor is constrained to \(ψ=\frac{Δh_0}{U^2_m}\le 0.40\) (where \(U_m=350~\mathrm{m/s}\) is the mean blade speed), determine the minimum number of stages (\(N\)) required and the resulting actual stage loading coefficient across all stages.

    References

    Mattingly, J. D., Heiser, W. H., & Pratt, D. T. (2002). Aircraft Engine Design (2nd ed.). American Institute of Aeronautics and Astronautics (AIAA).

    "The Design of High-Efficiency Turbomachinery and Gas Turbines" by David Gordon Wilson and Theodosios Korakianitis.


    This page titled 5.4: Problems and References was last modified on Wed, 18 Nov 2026 07:18:37 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Haifa El-Sadi.