Learn · NPTEL

Course11210642434 lectures

Design of Mechanical Transmission Systems

Prof. Ramkumar · IIT Madras

Start with lecture 1 At NPTEL

Lectures

week-01

  1. Course Introduction, Evaluation, and Application of Gearbox Video
  2. Machine Tool Gearbox: GP, Step Ratio, Preferred Numbers, Structural Formula&Rules of Optimum Gearbox Video
  3. Machine Tool Gearbox: Ray Diagram Construction Video

week-02

  1. Machine Tool Gearbox: Kinematic Diagram Construction Video
  2. Machine Tool Gearbox: Centre Distance and Teeth Calculation Video
  3. Machine Tool Gearbox: Problem Solving Video

Week 6

  1. Lecture 07_Automobile Gearbox: General Engine Operation and Transmission Types Video
  2. Lecture 08_Automobile Gearbox: Saw Tooth Diagram and Design Procedure for Gearbox Video
  3. Lecture 09_Automobile Gearbox: Problem Solving & Tyre Specification Video

week-04

  1. Lecture 10_Automobile Gearbox: Basic Transmission Types and Kinematic Diagram Video
  2. Lecture 11_Automobile Gearbox: Gear Failures and Material Selection Video
  3. Lecture 12_Automobile Gearbox: Module Calculation Concept - Part I Video

week-05

  1. Lecture 13_Automobile Gearbox: Module Calculation Concept - Part II Video
  2. Lecture 14_Automobile Gearbox: Shaft Design, Lubrication Selection and Method Video
  3. Lecture 15_Automobile Gearbox: Bearing Selection and Gearbox Losses Video

week-06

  1. Lecture 16_Brake: Introduction, Working Principle and Types Video
  2. Lecture 17_Brake: Torque Requirement for Drum Brake Systems Video
  3. Lecture 18_Brake: Problem Solving Video

week-07

  1. Lecture 19_Brake: Torque Requirement for Disc Brake Systems Video
  2. Lecture 20_Brake: Static and Dynamic Analysis Video
  3. Lecture 21_Brake: Dynamic Analysis – Brake Force Distribution and Optimum Video

week-08

  1. Lecture 22_Brake: Problem Solving Video
  2. Lecture 23_Brake: Braking Efficiency & Distance and Brake Factor Video
  3. Lecture 24_Brake: Problem Solving and Friction Materials Video

week-09

  1. Lecture 25_Brake: Thermal Analysis and Braking Conditions Video
  2. Lecture 26_Brake: Energy and Power, Braking Power Absorbed by Lining and Drum/Disc Video

week-10

  1. Lecture 27_Brake: Single Stop Braking and Repeated Braking – Temperature Analysis Video
  2. Lecture 28_Brake: Thermal Analysis Problem Solving Video

week-11

  1. Lecture 29_Clutch: Types and Working Method Video
  2. Lecture 30_Clutch: Torque Transmitting Capacity – Uniform Pressure & Wear Theories Video
  3. Lecture 31_Clutch: Multiple Discs and Cone Clutches, Problem Solving Video

week-12

  1. Lecture 32_Clutch: Centrifugal Clutch Video
  2. Lecture 33_Clutch: Dynamic Analysis Video
  3. Lecture 34_Clutch: Dynamic Analysis Problem Solving Video

Syllabus and materials

At NPTEL, as the course publishes them.

Credits and licence

Institution
IIT Madras
Department
Mechanical Engineering
Teacher
Prof. Ramkumar
Level
Undergraduate
Language
English
Subjects
Engineering
Source
NPTEL
Licence
CC BY-NC-SA, as NPTEL states it. Non-commercial use only. NPTEL's terms
Attribution
NPTEL states: "Distributed under Creative Commons Attribution-ShareAlike / CC BY - NC - SA", beside a BY-NC-SA badge.
Who can watch
NPTEL gives no rating. Invisible Network shows it to Tweens profiles and older, judged from what the source says about it. How courses are placed