Learn · Design of Steel Structures
Lecture 38 of 63Week 8
Lecture 38: Connection Design of Lacing Systems
Prof. Damodar Maity · IIT Kharagpur
Credits and licence
- From
- Design of Steel Structures, IIT Kharagpur (at NPTEL)
- Licence
- CC BY-NC-SA, as NPTEL states it. Non-commercial use only.
- Attribution
- NPTEL states: "Distributed under Creative Commons Attribution-ShareAlike / CC BY - NC - SA", beside a BY-NC-SA badge.
- Who can watch
- Tweens profiles and older. How courses are placed
All the lectures
- Lecture 1: Introduction to Design of Steel Structures (Limit State Method)
- Lecture 2: Steel as a Structural Material
- Lecture 3: Limit State Design
- Lecture 4: Introduction to Connections
- Lecture 5: Introduction to Bolt Connections
- Lecture 6: Design of Ordinary Black Bolts
- Lecture 7: Worked out Examples on Design of Ordinary Black Bolts
- Lecture 8: Design of High Strength Friction Grip Bolts
- Lecture 9: Weld connection
- Lecture 10: Design of Fillet Welds
- Lecture 11: Design of Butt Welds
- Lecture 12: Design of Plug and Slot Weld
- Lecture 13: Eccentric Connection (Load Lying in Plane of Bolted Joint)
- Lecture 14: Design of Eccentric Connection (Load Lying in Plane of Bolted Joint)
- Lecture 15: Eccentric Connection (Load Lying in Plane of Welded Joint)
- Lecture 16: Eccentric Connection (Load Lying Perpendicular to Plane of Bolted Joint)
- Lecture 17: Design of Eccentric Connection (Load Lying Perpendicular to Plane of Bolted Joint)
- Lecture 18: Eccentric Connection (Load Lying Perpendicular to Plane of Welded Joint)
- Lecture 19: Tension Members and Net Area
- Lecture 20: Calculation of Net Area in Tension Member
- Lecture 21: Calculation of Net Area in Tension Member
- Lecture 22: Strength Calculation of Tension Member
- Lecture 23: Strength of Tension Members with Weld Connection
- Lecture 24: Steps for Design of Tension Members
- Lecture 25: Design Calculation of Tension Members
- Lecture 26: Design of Gusset Plate
- Lecture 27: Lug Angles
- Lecture 28: Splices in Tension Members
- Lecture 29: Compression Members
- Lecture 30: Design Strength of Compression Members
- Lecture 31: Compressive Strength
- Lecture 32: Compressive Strength of Angle Struts
- Lecture 33: Compressive Strength of Double Angles
- Lecture 34: Design of Compression Members
- Lecture 35: Design of Builtup Compression Members
- Lecture 36: Lacing Systems
- Lecture 37: Design of Lacing Systems
- Lecture 38: Connection Design of Lacing Systems
- Lecture 39: Design of Double Lacing System
- Lecture 40: Batten Plates
- Lecture 41: Design of Batten Plates using Bolt Connection
- Lecture 42: Design of Batten Plates using Weld Connection
- Lecture 43: Design of Column Splices
- Lecture 44: Design of Column Splices due to Shear
- Lecture 45: Introduction to Flexural Member
- Lecture 46: Failure Modes of Flexural Member
- Lecture 47: Laterally Supported Beams
- Lecture 48: Design of Laterally Supported Beams
- Lecture 49: Laterally supported beam with high shear
- Lecture 50: Laterally unsupported beams
- Lecture 51: Strength Calculation of Laterally Unsupported Beams
- Lecture 52 : Design of Laterally Unsupported Beams
- Lecture 53 : Calculation of Plastic Section Modulus
- Lecture 54 : Purlins
- Lecture 55: Design of Purlins
- Lecture 56 : Introduction to Gantry Girders
- Lecture 57 : Design of Gantry Girder
- Lecture 58 : Worked out Example for Gantry Girder
- Lecture 59 : Slab Base
- Lecture 60 : Design of Slab Base
- Lecture 61 : Eccentrically Loaded Base Plate
- Lecture 62 : Gusset Base
- Lecture 63 : Design of Gusset Base