21.1: Circuit Elements and Diagrams

Physics: A Foundation for Scientists and Engineers · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    21.1: Circuit Elements and Diagrams
    The standard symbols used in circuit diagrams, in two rows of four.
    Figure 21.1. Symbols used in circuit diagrams. The long line of the battery symbol is its positive terminal.
    Figure descriptionThe standard symbols used in circuit diagrams, in two rows of four. Top row: wires, drawn as straight lines, with a dot marking a junction where three wires meet; a battery, drawn as a long thin line and a short thick line side by side, the long line marked plus; a resistor, drawn as a zigzag; and a capacitor, drawn as two short parallel lines of equal length. Bottom row: an open switch, drawn as a gap with a hinged blade tilted up; a lamp, drawn as a circle with an X in it; an ammeter, drawn as a circle containing the letter A; and a voltmeter, drawn as a circle containing the letter V.

    An electric circuit is a closed path, or a network of paths, around which charge can flow. It is built from a small number of kinds of element, joined by wires. To describe a circuit, we draw a circuit diagram, in which each element is replaced by a standard symbol (Figure 21.1). A circuit diagram shows how the elements are connected, not where they sit or what they look like: the lines are ideal wires with no resistance, and they may be stretched, bent, or redrawn in any way that keeps the same connections. Every point along a single wire, and everything attached directly to it, is at the same potential. A point where three or more wires meet is a junction, marked with a dot.

    The battery and its emf. Charge flowing through a resistor always moves from high potential to low, losing potential energy. For a steady current to flow around a closed loop, something must lift the charge back up to high potential. A battery does this. Inside it, chemical reactions push positive charge from the negative terminal to the positive terminal, against the electric field there, doing work on it. (In a metal the carriers are electrons, pushed the other way, but the energy accounting is the same.) The battery is to charge what a pump is to water in a closed loop of pipe, or a ski lift to skiers: it raises them to a height from which they can run back down.

    The work done by the source per unit charge that passes through it is called its emf, symbol \(\mathcal{E}\):

    Key Equation: Emf of a source

    \[\mathcal{E} = \frac{W}{q}. \tag{21.1}\]

    Its SI unit is the volt, one joule per coulomb. The name is short for “electromotive force,” a historical term that is misleading, since emf is not a force at all but an energy per unit charge; physicists now simply say “emf” (e-m-f). A battery with an emf of \(1.5\,\mathrm{V}\) gives each coulomb that passes through it \(1.5\,\mathrm{J}\) of energy. Batteries are just one example of a source of emf; the generators of Chapter 24, solar cells, and thermocouples are others.

    An ideal battery maintains a potential difference between its terminals called its terminal voltage. This is exactly equal to its emf, however much current it delivers. Real batteries fall short of this, as Section 21.4 will show, but until then every battery is ideal: the potential of its positive terminal is higher than that of its negative terminal by exactly \(\mathcal{E}\).

    Example 21.1: The energy in a battery

    An AA battery has an emf of \(1.5\,\mathrm{V}\) and a capacity of about \(2500\,\mathrm{mAh}\) (Chapter 20). How much energy can it deliver?

    Solution

    The capacity is the charge it can move through a circuit: \(Q = (2.5\,\mathrm{A})(3600\,\mathrm{s}) = 9000\,\mathrm{C}\). Each coulomb gains \(1.5\,\mathrm{J}\), so the energy is

    \[W = Q\mathcal{E} = (9000\,\mathrm{C})(1.5\,\mathrm{V}) = \boxed{1.4\times 10^{4}\,\mathrm{J}}.\]

    That is enough to lift a \(70\,\mathrm{kg}\) person about \(20\,\mathrm{m}\), or to run a \(1\,\mathrm{W}\) flashlight bulb for nearly four hours. By comparison, the same mass of gasoline, about \(23\,\mathrm{g}\), holds nearly eighty times as much chemical energy, which is one reason electric cars need such large battery packs.

    Two panels of a battery and lamps A and B, showing the effect of a short circuit.
    Figure 21.2. A short circuit. (a) Current flows around the whole loop, through the battery and both lamps. (b) A wire of negligible resistance connects the two ends of lamp \(B\). The current takes this path instead, bypassing lamp \(B\), which goes dark. With less total resistance in the circuit, the current through the battery and lamp \(A\) increases, and lamp \(A\) glows more brightly. A short directly across the battery would bypass everything, leaving only the battery’s own small resistance to limit the current.
    Figure descriptionTwo panels showing the same simple circuit: a battery on the left side of a rectangular loop, lamp A on the top side, and lamp B on the right side. In panel a, current I flows around the whole loop, through the battery and both lamps, and both lamps are lit. In panel b, a red wire of negligible resistance, labeled short, connects the two ends of lamp B, running around its outside. The current now flows through the short instead of through lamp B, so lamp B is dark and labeled no current. Lamp A is drawn brighter, and the current around the rest of the loop is labeled as larger.

    Switches, open circuits, and short circuits. A switch opens or closes a gap in a wire. When the switch is open, there is no complete path, and no current can flow; the circuit is an open circuit. A short circuit, or short, results when a wire of negligible resistance connects two points of a circuit so that current bypasses the circuit elements between those points (Figure 21.2). A short across a battery draws an enormous current, limited only by the battery’s own resistance, and can overheat the battery or the wire dangerously.

    Circuit of a battery and resistor R, showing where an ammeter is connected.
    Figure 21.3. Measuring current. The circuit is broken and the ammeter inserted in series with the resistor, so that the current through the resistor must also pass through the ammeter. An ideal ammeter has zero resistance, so inserting it does not change the current.
    Figure descriptionA circuit diagram with a battery of emf script E on the left, positive terminal on top, connected in a rectangular loop to a resistor R on the right side. The top wire has been broken and an ammeter, a circle marked A, inserted in the gap, so that the ammeter and the resistor lie one after the other along the same single path. The current I, flowing clockwise, is shown by arrows on the wire entering the ammeter and on the wire leaving it, and continues down through the resistor, so the same current passes through the ammeter and the resistor.
    Circuit of a battery and resistor R, showing where a voltmeter is connected.
    Figure 21.4. Measuring potential difference. The voltmeter is connected across the resistor, in parallel with it, without breaking the circuit; its two leads touch the two ends of the resistor, so it has the same potential difference \(V_R\) across it. An ideal voltmeter has infinite resistance, so it draws no current and does not disturb the circuit.
    Figure descriptionA circuit diagram with a battery of emf script E on the left, positive terminal on top, connected in a rectangular loop to a resistor R on the right side. No wire of the loop is broken. A voltmeter, a circle marked V, sits to the right of the resistor, and two extra wires connect its terminals to junction dots at the top and bottom ends of the resistor, so that the voltmeter and the resistor are side by side in parallel, spanning the same two points. The potential difference V sub R across the resistor is marked with a plus sign at its top end and a minus sign at its bottom end.

    Measuring current and voltage. An ammeter measures the current through a wire. To do so, the current must flow through it, so it is connected in series: the wire is cut, and the ammeter is inserted in the gap (Figure 21.3). A voltmeter measures the potential difference between two points, so it is connected directly across them, in parallel with the element being measured, without cutting any wire (Figure 21.4). An ideal ammeter has zero resistance, so inserting it changes nothing; an ideal voltmeter has infinite resistance, so it draws no current. Real meters come close enough for most purposes; the digital multimeters found in every laboratory measure both, and resistance too.

    Checkpoint 21.1

    A student connects an ammeter directly across a resistor, the way a voltmeter should be connected. (a) Since the ammeter has almost no resistance, where does nearly all the current now flow? (b) Why might this damage the ammeter?

    Answer

    Answers to Checkpoints

    Checkpoint 21.1. (a) Through the ammeter. Connected across the resistor, it is in parallel with it, and nearly all the current takes the almost-zero-resistance path, bypassing the resistor. (b) The ammeter has effectively short-circuited the resistor, so the current in the circuit is now limited only by whatever resistance remains elsewhere: perhaps just the battery’s internal resistance. That current can be far larger than the meter is built to carry, blowing its fuse or burning out its coil.


    This page titled 21.1: Circuit Elements and Diagrams was last modified on Thu, 12 Nov 2026 04:26:44 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.