Opening the book…
In translation, mass measures an object’s resistance to a change in motion. In rotation, that role is played by rotational inertia, or moment of inertia \(I\), and it depends not just on how much mass there is but on how that mass is distributed relative to the axis. Mass far from the axis is much harder to spin up than mass close in. A single particle of mass \(m\) at distance \(r\) from the axis has \(I = mr^2\); for an extended body we add up the contributions:
Key Equation: Moment of inertia
\[I = \sum_i m_i r_i^2 \quad\text{(particles)}, \qquad I = \int r^2\,dm \quad\text{(continuous body)}. \tag{10.10}\]
The \(r^2\) weighting is why distribution matters so much: doubling a particle’s distance from the axis quadruples its contribution. The SI unit of \(I\) is \(\,\mathrm{kg\cdot m^2}\).
Example 10.2: Moment of inertia of a thin rod
Find the moment of inertia of a uniform thin rod of length \(L\) and mass \(M\) about an axis perpendicular to the rod through its center.
Solution
Step 1: Picture what \(dm\) means. The integral \(I = \int r^2\,dm\) is an instruction: chop the body into tiny pieces, multiply each piece’s mass \(dm\) by the square of its distance \(r\) from the axis, and add up all the pieces. For the rod, cut it into thin slices across its length, as in the figure. Measure position \(x\) along the rod from its center, so the rod runs from \(x = -L/2\) to \(x = +L/2\) and the axis sits at \(x = 0\).
Step 2: Describe each slice by its position. We cannot integrate “over mass” directly: there is no mass variable to put limits on. What we can describe is where each slice sits. So we rewrite everything inside the integral in terms of the single variable \(x\), one piece at a time.
- The distance. A slice at position \(x\) is a distance \(r = |x|\) from the axis, so \(r^2 = x^2\) (squaring removes the absolute value).
- The mass. The slice has width \(dx\). The rod is uniform, so every meter of it has the same mass, \(\lambda = M/L\) (its linear mass density). A slice’s mass is then (mass per length) \(\times\) (length):
\[dm = \lambda\,dx = \frac{M}{L}\,dx.\]
- The limits. “Add up every piece of mass” now means “add up every slice from one end of the rod to the other”: \(x\) runs from \(-L/2\) to \(+L/2\). The limits are positions, because the variable is now a position.
Two quick checks that the swap is right. Units: \((M/L)\,dx\) is \((\,\mathrm{kg/m})(\,\mathrm{m}) = \,\mathrm{kg}\), a mass, as \(dm\) must be. And adding up all the slices with no \(r^2\) weighting must give back the whole rod:
\[\int dm = \int_{-L/2}^{L/2} \frac{M}{L}\,dx = \frac{M}{L}\Big[x\Big]_{-L/2}^{L/2} = \frac{M}{L}\left(\frac{L}{2} + \frac{L}{2}\right) = M. \;\checkmark\]
Now make all three replacements at once in the moment-of-inertia integral:
\[I = \int r^2\,dm \quad\longrightarrow\quad I = \int_{-L/2}^{L/2} x^2\,\frac{M}{L}\,dx = \frac{M}{L}\int_{-L/2}^{L/2} x^2\,dx.\]
The constant \(M/L\) comes outside the integral, leaving an ordinary power-rule integral in \(x\).
Step 3: Integrate and evaluate. By the power rule, \(\int x^2\,dx = x^3/3\). Evaluate at the upper limit and subtract the value at the lower limit. The cube of a negative number is negative, \((-L/2)^3 = -L^3/8\), so subtracting it adds:
\[\left[\frac{x^3}{3}\right]_{-L/2}^{L/2} = \frac{(L/2)^3}{3} - \frac{(-L/2)^3}{3} = \frac{L^3}{24} - \left(-\frac{L^3}{24}\right) = \frac{L^3}{24} + \frac{L^3}{24} = \frac{L^3}{12}.\]
Therefore
\[I = \frac{M}{L}\cdot\frac{L^3}{12} = \boxed{\tfrac{1}{12}ML^2},\]
where one power of \(L\) canceled. The two halves of the rod contribute equally, which is why the answer is twice the \(L^3/24\) from either half.
The end axis. If instead the axis passes through one end, \(x\) runs from \(0\) to \(L\), and the same integral gives
\[I = \frac{M}{L}\int_0^L x^2\,dx = \frac{M}{L}\cdot\frac{L^3}{3} = \tfrac{1}{3}ML^2,\]
four times larger, because more of the mass now lies far from the axis. (The parallel-axis theorem checks this: \(\tfrac{1}{12}ML^2 + M(L/2)^2 = \tfrac{1}{12}ML^2 + \tfrac{3}{12}ML^2 = \tfrac{1}{3}ML^2\).)
Integrals like this have been worked out for all the common shapes; Table 10.1 collects the most useful results. Each is some pure number times \(MR^2\) or \(ML^2\), with the number reflecting how the mass is spread.
| Body (axis) | Moment of inertia |
|---|---|
| Thin hoop / ring (central axis) | \(MR^2\) |
| Solid cylinder or disk (central axis) | \(\tfrac{1}{2}MR^2\) |
| Thin rod (through center, \(\perp\)) | \(\tfrac{1}{12}ML^2\) |
| Thin rod (through end, \(\perp\)) | \(\tfrac{1}{3}ML^2\) |
| Solid sphere (through center) | \(\tfrac{2}{5}MR^2\) |
| Thin spherical shell (through center) | \(\tfrac{2}{3}MR^2\) |
The parallel-axis theorem
Table 10.1 gives \(I\) about an axis through the center of mass, but real objects often turn about some other axis: a rod swinging from one end, a door on its hinges, a pedal about a crank. Redoing the integral for every new axis would be tedious, and happily it is unnecessary. If you know \(I_{\rm cm}\) about an axis through the center of mass, then about any parallel axis a distance \(d\) away,
Key Equation: Parallel-axis theorem
\[I = I_{\rm cm} + Md^{2}. \tag{10.11}\]
Here \(M\) is the total mass of the body and \(d\) is the perpendicular distance between the two axes (Figure 10.3). The two conditions are easy to state and easy to forget: the axes must be parallel to each other, and one of them must pass through the center of mass. The theorem says nothing about two arbitrary axes.
Two features of equation (10.11) are worth pausing on. First, \(Md^2\) can never be negative, so the moment of inertia is smallest about an axis through the center of mass; every parallel axis is harder to spin the body about. Second, the added term is exactly what you would get by treating the entire body as a single point mass \(M\) sitting at the center of mass, a distance \(d\) from the axis.
The rod worked out above makes a ready check. Its center-of-mass value is \(I_{\rm cm} = \tfrac{1}{12}ML^2\), and the axis through one end is parallel to that one and a distance \(d = L/2\) from it, so
\[I_{\rm end} = \tfrac{1}{12}ML^{2} + M\!\left(\frac{L}{2}\right)^{\!2} = \tfrac{1}{12}ML^{2} + \tfrac{1}{4}ML^{2} = \tfrac{1}{3}ML^{2},\]
which matches the integral exactly, and took one line instead of one integration.
Checkpoint 10.3
A solid disk of mass \(M\) and radius \(R\) has \(I_{\rm cm} = \tfrac{1}{2}MR^2\) about its central axis. Find its moment of inertia about a parallel axis through a point on its rim. Is the result larger or smaller than \(I_{\rm cm}\), and did it have to come out that way?
Answers to Checkpoints
Checkpoint 10.3. By the parallel-axis theorem with the axis a distance \(R\) from the center, \(I = I_{\rm cm} + MR^2 = \tfrac{1}{2}MR^2 + MR^2 = \tfrac{3}{2}MR^2\). That is three times \(I_{\rm cm}\), and it had to be larger: the added term \(Md^2\) is never negative, so the moment of inertia about the center of mass is the smallest of any parallel axis.
This page titled 10.3: Rotational Inertia was last modified on Thu, 12 Nov 2026 04:26:58 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.
The book could not be loaded just now.