Opening the book…
Because Newton’s second law involves the net force on one object, the indispensable first step in nearly every dynamics problem is to isolate a single object and inventory every force acting on it. The drawing that records this inventory is called a free-body diagram. Mastering it is the most valuable single skill in this chapter.
To draw a free-body diagram:
- Choose the object (the “body”) you will analyze, and mentally cut it free of everything else. Represent it as a dot or a simple box.
- Draw every force that acts on that body, and only those forces, as an arrow pointing away from the body in the direction the force acts. Include weight (always present near the Earth), and one contact force for each thing that touches the body: a surface (normal force, friction), a rope (tension), a hand (an applied push or pull).
- Do not draw forces the body exerts on other things, and do not draw “the force of motion”: there is no such force. A moving object coasting freely has no forward force on it.
- Choose coordinate axes. For an object on an incline it is almost always best to tilt the axes so that one axis lies along the surface and the other is perpendicular to it; then the normal force lies along an axis and only the weight must be decomposed.
Figure 5.1 shows a block resting on a frictionless ramp and the free-body diagram that goes with it. Only two forces act on the block: its weight \(\vec{F}_g\), straight down, and the normal force \(\vec{F}_N\), perpendicular to the ramp surface. With axes tilted to the incline, the weight is the only vector that must be broken into components.
With the tilted axes of Figure 5.1, the weight has a component \(mg\sin\theta\) pointing down the slope (along \(-x\)) and a component \(mg\cos\theta\) pressing into the surface (along \(-y\)). The normal force lies entirely along \(+y\).
Why does the slope component get the sine, when the ramp’s angle \(\theta\) is marked way down at the bottom of the triangle? Because that same angle reappears inside the free-body diagram, as the right-hand triangle in Figure 5.1 shows: the angle between \(\vec{F}_g\) and the perpendicular to the surface is also \(\theta\), since the two angles have mutually perpendicular sides. Once you see that, the components are just the usual right-triangle rules. The side adjacent to \(\theta\) presses into the surface, giving \(mg\cos\theta\); the side opposite \(\theta\) runs down the slope, giving \(mg\sin\theta\).
If you ever doubt which is which, check the extremes. As \(\theta \to 0\) the ramp flattens out, the slope component \(mg\sin\theta\) vanishes, and \(F_N \to mg\): the object just sits on level ground. As \(\theta \to 90^\circ\) the ramp becomes a vertical cliff, \(F_N \to 0\), and the entire weight \(mg\sin\theta \to mg\) pulls along the “slope,” which by then points straight down. Both limits are what they should be, so the assignment of sine and cosine is right. Writing Newton’s second law for each axis is then routine, as we will see repeatedly in §5.5.
Checkpoint 5.3
A hockey puck, struck by a stick, slides across frictionless ice at constant velocity. List every force acting on the puck after it has left the stick, and sketch its free-body diagram. Is there any force pointing in the direction the puck is moving?
Answers to Checkpoints
Checkpoint 5.3. Only two forces act: the weight \(m\vec{g}\), straight down, and the normal force \(\vec{F}_N\) from the ice, straight up. They balance, since the puck does not accelerate vertically. There is no force in the direction of motion: the stick’s push ended when contact ended, and on frictionless ice nothing is needed to keep the puck moving. By the first law, zero net force means constant velocity, not rest. An arrow along the motion would be the nonexistent “force of motion.”
This page titled 5.3: Free-Body Diagrams was last modified on Thu, 12 Nov 2026 04:26:42 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.
The book could not be loaded just now.