26.2: Resistors in an AC Circuit

Physics: A Foundation for Scientists and Engineers · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    26.2: Resistors in an AC Circuit

    An ac generator (Section 24.4) produces a sinusoidal emf. We write the voltage of such a source as

    \[v = V_m\sin\omega t,\]

    where \(V_m\) is its amplitude, and \(\omega = 2\pi f\) is the driving angular frequency, set by the source. Lowercase letters \(v\) and \(i\) stand for the instantaneous values, which change with time; capitals stand for amplitudes and other constants. The current that such a source drives is an alternating current.

    Voltage and current of a resistor in an ac circuit: sine curves in phase.
    Figure 26.2. A resistor in an ac circuit. (a) The current and voltage are in phase. (b) Their phasors point in the same direction and rotate together; the vertical components are the instantaneous values.
    Figure descriptionPanel a: graphs against time of the voltage v across a resistor and the current i through it, both sine curves that reach their peaks and zeros at the same times: they are in phase. Panel b: a phasor diagram. The voltage phasor, of length V sub m, and the current phasor, of length I sub m, point in the same direction, at angle omega t above the horizontal axis, and rotate counterclockwise together. Their projections onto the vertical axis are the instantaneous values v and i.

    Connect the source across a resistor \(R\). The loop rule gives \(v - iR = 0\) at every instant, so

    \[i_R = \frac{V_m}{R}\sin\omega t = I_m\sin\omega t, \qquad I_m = \frac{V_m}{R}. \tag{26.3}\]

    The current and the voltage rise and fall together: they are in phase (Figure 26.2a). Ohm’s law holds for the amplitudes, \(V_m = I_mR\), and at every instant.

    Phasors. Keeping track of the phases of several sinusoids is much easier with a picture. Represent a quantity that varies as \(V_m\sin(\omega t + \phi)\) by a vector of length \(V_m\) that rotates counterclockwise with angular velocity \(\omega\), making the angle \(\omega t + \phi\) with the horizontal axis. Its vertical component is \(V_m\sin(\omega t + \phi)\), the instantaneous value. Such a rotating vector is called a phasor. Several quantities with the same frequency are drawn as phasors rotating together, and the angles between them show their phase differences. For a resistor, the current phasor and the voltage phasor point in the same direction (Figure 26.2b). (Chapter 29 uses phasors in the same way to add waves.) If phasors are new to you, Section C.8 of Appendix C builds them up step by step, with pictures of how a rotating phasor traces out a sine curve, what it means for one sinusoid to lead another, and how adding phasors adds sinusoids.

    Rms values. The average of a sinusoidal current over a cycle is zero, which is not a useful measure of its size. What matters for heating is the average of \(i^2\), since the power in a resistor is \(i^2R\). Because the average of \(\sin^2\omega t\) over a cycle is \(\frac{1}{2}\), the average power is \(\frac{1}{2}I_m^2R\). A steady current that delivers the same power is the root-mean-square, or rms, current: the square root of the mean of the square,

    Key Equation: Rms values

    \[I_{\text{rms}} = \frac{I_m}{\sqrt{2}}, \qquad V_{\text{rms}} = \frac{V_m}{\sqrt{2}}. \tag{26.4}\]

    Ac meters read rms values, and ac voltages and currents are quoted as rms values unless stated otherwise. The “\(120\,\mathrm{V}\)” of a North American outlet is an rms voltage; its amplitude is \(\sqrt{2}(120) = 170\,\mathrm{V}\). With rms values, the formulas for power in a resistor look just as they do for dc: \(P_{\text{avg}} = I_{\text{rms}}^2R = V_{\text{rms}}^2/R = I_{\text{rms}}V_{\text{rms}}\).

    Example 26.3: A lamp on ac

    A \(60\,\mathrm{W}\) lamp is designed for a \(120\,\mathrm{V}\) (rms) outlet. Find (a) its resistance, (b) the rms and peak currents, and (c) the peak power.

    Solution

    (a) \(R = V_{\text{rms}}^2/P_{\text{avg}} = (120)^2/60 = \boxed{240\,\mathrm{\Omega}}\), the same lamp as in Chapter 20.

    (b) \(I_{\text{rms}} = V_{\text{rms}}/R = \boxed{0.50\,\mathrm{A}}\), and \(I_m = \sqrt{2}\,I_{\text{rms}} = \boxed{0.71\,\mathrm{A}}\).

    (c) The instantaneous power is \(i^2R = I_m^2R\sin^2\omega t\), which peaks at \(I_m^2R = (0.71)^2(240) = \boxed{120\,\mathrm{W}}\), twice the average. It falls to zero twice each cycle, \(120\) times a second, but the filament is too hot to cool noticeably in so short a time, so the lamp does not visibly flicker.


    This page titled 26.2: Resistors in an AC Circuit was last modified on Thu, 12 Nov 2026 04:26:59 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.