Opening the book…
A circuit containing a resistor and an inductor, an RL circuit, behaves much like the RC circuit of Section 21.5, but with the roles of current and charge exchanged. In Figure 25.3, the switch can connect a battery to the resistor and inductor in series (position \(a\)), or remove the battery and connect the resistor and inductor to each other (position \(b\)).
Current rising. Throw the switch to \(a\) at \(t = 0\). Going around the loop in the direction of the current, the loop rule gives
\[\mathcal{E} - IR - L\frac{dI}{dt} = 0. \tag{25.8}\]
At the first instant, the current is zero, and the whole emf appears across the inductor: \(dI/dt = \mathcal{E}/L\). The inductor behaves like a break in the circuit, the opposite of an uncharged capacitor. As the current grows, more of the emf is taken up by the resistor, and the current rises more slowly, approaching the final value \(I_f = \mathcal{E}/R\) at which \(dI/dt = 0\) and the inductor behaves like a plain wire. Equation (25.8) has the same form as the equation for a charging capacitor, with \(L\) in place of \(R\), \(R\) in place of \(1/C\), and \(I\) in place of \(q\), and it has the same kind of solution:
Key Equation: Current rising in an RL circuit
\[I(t) = \frac{\mathcal{E}}{R}\left(1 - e^{-t/\tau}\right), \qquad \tau = \frac{L}{R}. \tag{25.9}\]
The inductive time constant \(\tau = L/R\) has units of seconds: a henry is a \(\,\mathrm{V\cdot s/A}\) and an ohm is a \(\,\mathrm{V/A}\), so \(1\,\mathrm{H}/1\,\Omega = 1\,\mathrm{s}\). After one time constant the current has reached \(63\%\) of its final value. A larger inductance slows the rise, since the inductor opposes change more strongly; a larger resistance speeds it up, because the final current, and so the change the inductor must oppose, is smaller. The emf across the inductor, \(L\,dI/dt = \mathcal{E}e^{-t/\tau}\), decays from \(\mathcal{E}\) to zero.
Current decaying. Once the current has reached \(I_0\), throw the switch to \(b\). The battery is removed, but the inductor keeps the current flowing, now through the resistor alone, and the loop rule gives \(-IR - L\,dI/dt = 0\). The current decays exponentially with the same time constant:
Key Equation: Current decaying in an RL circuit
\[I(t) = I_0\,e^{-t/\tau}, \qquad \tau = \frac{L}{R}. \tag{25.10}\]
During the decay, the energy \(\frac{1}{2}LI_0^2\) stored in the inductor’s field is delivered to the resistor as heat (Problem 25.18).
Example 25.5: Switching on an RL circuit
A coil with inductance \(0.50\,\mathrm{H}\) and resistance \(10\,\mathrm{\Omega}\) is connected to a \(12\,\mathrm{V}\) battery. Find (a) the time constant, (b) the final current, (c) the initial rate of increase of the current, and (d) the time for the current to reach \(90\%\) of its final value.
Solution
(a) \(\tau = L/R = 0.50/10 = \boxed{0.050\,\mathrm{s}}\).
(b) \(I_f = \mathcal{E}/R = 12/10 = \boxed{1.2\,\mathrm{A}}\).
(c) At \(t = 0\), the current is zero, so the whole emf is across the inductor: \(dI/dt = \mathcal{E}/L = 12/0.50 = \boxed{24\,\mathrm{A/s}}\). If the current kept rising at this rate, it would reach \(I_f\) in exactly one time constant.
(d) Setting \(1 - e^{-t/\tau} = 0.90\) gives \(e^{-t/\tau} = 0.10\), so
\[t = \tau\ln 10 = (0.050)(2.30) = \boxed{0.12\,\mathrm{s}}.\]
Breaking an inductive circuit. What if the current in an inductor is simply switched off, by opening a switch, with no path like \(b\) for it to continue? Then \(dI/dt\) is enormous, and so is the self-induced emf, \(L\,dI/dt\). It can reach thousands of volts, enough to ionize the air across the opening switch contacts and drive a spark, through which the current, and the energy stored in the field, find a way to escape. This is the spark seen when a plug is pulled from a running motor, and it slowly erodes the contacts of switches and relays. Circuits that switch inductive loads include a path, often a diode, to let the current decay gently instead. The same effect is put to use in a car’s ignition coil, which interrupts the current in a coil to produce the tens of kilovolts that fire the spark plugs.
Example 25.6: A spark from an inductor
A relay coil with an inductance of \(2.0\,\mathrm{H}\) carries \(1.5\,\mathrm{A}\). The circuit is broken, and the current falls to zero in about \(1.0\,\mathrm{ms}\). Estimate the induced emf and the energy that must be dissipated.
Solution
\[|\mathcal{E}_L| \approx L\frac{\Delta I}{\Delta t} = (2.0)\frac{1.5}{1.0\times10^{-3}} = \boxed{3000\,\mathrm{V}},\]
far more than the few volts that were driving the coil. The energy to be dissipated is the energy stored in the field, \(\frac{1}{2}LI^2 = \frac{1}{2}(2.0)(1.5)^2 = \boxed{2.3\,\mathrm{J}}\), released in a millisecond: a power of more than two kilowatts, concentrated in a tiny spark.
Checkpoint 25.3
In the circuit of Figure 25.3, with the switch at \(a\): (a) What is the potential difference across the inductor just after the switch is closed, and long afterward? (b) Compare with a capacitor in place of the inductor. (c) What is the energy stored in the inductor long after the switch is closed?
Answers to Checkpoints
Checkpoint 25.3. (a) Just after the switch closes the current is still zero, so there is no voltage across the resistor and the inductor’s back emf takes up the entire battery voltage: \(V_L = \mathcal{E}\). Long afterward the current is steady, so \(dI/dt = 0\) and \(V_L = 0\); the inductor behaves like a plain wire. (b) A capacitor behaves the opposite way: just after closing, an uncharged capacitor has \(V_C = 0\) and acts like a wire; long afterward it is fully charged, with \(V_C = \mathcal{E}\), and carries no current. (c) Long afterward the current is \(\mathcal{E}/R\), so \(U_B = \tfrac{1}{2}L(\mathcal{E}/R)^2\).
This page titled 25.3: RL Circuits was last modified on Thu, 12 Nov 2026 04:27:15 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.
The book could not be loaded just now.