Opening the book…
A surface on which the potential has the same value everywhere is called an equipotential surface, or simply an equipotential. The dashed lines in Figure 18.1 are equipotentials seen edge-on. Equipotentials are to the potential what contour lines on a topographic map are to height, and they have three important properties.
- No work is done moving a charge along an equipotential. Since \(\Delta V = 0\), equation (18.3) gives \(\Delta U = 0\).
- The field is perpendicular to the equipotentials everywhere. If \(\vec{E}\) had a component along an equipotential surface, a small step along the surface would change the potential by \(-\vec{E}\cdot d\vec{s} \ne 0\), contradicting property 1. The field points from higher equipotentials toward lower ones, the direction of steepest descent.
- Equipotentials drawn at equal steps of potential crowd together where the field is strong. For a small step \(\Delta s\) perpendicular to the equipotentials, \(|\Delta V| \approx E\,\Delta s\), so a fixed \(\Delta V\) is crossed in a shorter distance where \(E\) is larger, just as closely spaced contour lines on a map mark a steep hillside.
Figure 18.3 shows the equipotentials of a uniform field, which are parallel planes, and of a point charge, which are concentric spheres, crowded near the charge where the field is strong. Figure 18.2 shows those of an electric dipole, together with its field lines. Everywhere the two families cross at right angles.
Conductors are equipotentials. Inside a conductor in electrostatic equilibrium the field is zero (Section 17.5). By equation (18.1), the potential difference between any two points in the metal is then zero: every point of a conductor in equilibrium, inside and on its surface, is at the same potential. Its surface is an equipotential, which is another way of seeing that the field just outside it must be perpendicular to the surface.
Why charge crowds at sharp points. Chapter 17 claimed that on an irregular conductor the charge density is greatest where the surface curves most sharply. The equipotential property explains why. Consider two conducting spheres of radii \(R_1\) and \(R_2\), far apart, joined by a long thin wire so that they form a single conductor (Figure 18.4). The whole arrangement is one equipotential, so the two spheres have the same potential. The potential of a charged sphere is \(k_eQ/R\) (Section 18.3), so
\[\frac{k_eQ_1}{R_1} = \frac{k_eQ_2}{R_2} \qquad\Longrightarrow\qquad \frac{Q_1}{R_1} = \frac{Q_2}{R_2}.\]
The larger sphere holds more charge, but in proportion only to its radius, while its area grows as the square of its radius. Writing \(Q = 4\pi R^2\sigma\) gives \(\sigma_1R_1 = \sigma_2R_2\): the surface charge density is inversely proportional to the radius. The field just outside is \(\sigma/\epsilon_0\) (equation (17.6)), so it too is largest on the smaller sphere. A sharp point on a conductor behaves like a very small sphere, and the field there can be strong enough to ionize the air. This is the corona discharge of Section 17.5, and it is why a lightning rod is pointed: its tip leaks charge into the air gradually and offers the lightning a preferred path to ground.
Example 18.5: Two connected spheres
Two conducting spheres, of radii \(R_1 = 10.0\,\mathrm{cm}\) and \(R_2 = 2.0\,\mathrm{cm}\), are far apart but joined by a thin wire, and together carry \(+60\,\mathrm{nC}\). Find the charge on each sphere and the field just outside each surface.
Solution
Equal potentials require \(Q_1/R_1 = Q_2/R_2\), so \(Q_1 = 5Q_2\). With \(Q_1 + Q_2 = 60\,\mathrm{nC}\), the charges are \(Q_2 = \boxed{10\,\mathrm{nC}}\) and \(Q_1 = \boxed{50\,\mathrm{nC}}\). The field just outside each sphere is \(k_eQ/R^2\):
\[\begin{aligned}E_1 &= \frac{(8.99\times10^{9})(50\times10^{-9})}{(0.100)^2} = \boxed{4.5\times 10^{4}\,\mathrm{V/m}}, \\ E_2 &= \frac{(8.99\times10^{9})(10\times10^{-9})}{(0.020)^2} = \boxed{2.2\times 10^{5}\,\mathrm{V/m}}.\end{aligned}\]
The small sphere carries a fifth as much charge but has five times the surface field, in keeping with \(E \propto \sigma \propto 1/R\).
An empty cavity in a conductor. Chapter 17 showed that the walls of an empty cavity in a conductor carry no net charge, and promised that they carry no charge at all. Suppose the wall had a patch of positive charge somewhere and a patch of negative charge elsewhere, adding to zero (Figure 18.5a). Then field lines would leave the positive patch, cross the empty cavity, and end on the negative patch. Integrating \(-\vec{E}\cdot d\vec{s}\) along one of those field lines gives a potential drop from the first patch to the second, since the field points along the path all the way. But both patches are on the same conductor, which is an equipotential. The contradiction means there can be no such field lines: the cavity wall carries no charge anywhere, and the field inside the cavity is zero (Figure 18.5b). This is the full justification for the Faraday cage of Section 17.5.
Checkpoint 18.3
(a) Can two different equipotential surfaces ever intersect? Explain. (b) A charged conductor has a flat face and a pointed tip. Where is the potential higher, on the face or at the tip? Where is the field just outside higher?
Answers to Checkpoints
Checkpoint 18.3. (a) No. Every point has a single value of potential. At an intersection that point would have to be at two different potentials at once. (b) The potential is the same everywhere on the conductor (face and tip alike) because a conductor in equilibrium is an equipotential. The field just outside is much stronger at the tip, because charge crowds onto sharply curved regions, and \(E = \sigma/\epsilon_0\) is larger where \(\sigma\) is larger.
This page titled 18.2: Equipotential Surfaces was last modified on Thu, 12 Nov 2026 04:27:02 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.
The book could not be loaded just now.