21.E: DC Circuits (Problems)

Physics: A Foundation for Scientists and Engineers · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    21.E: DC Circuits (Problems)

    Difficulty key: ★ introductory, ★★ standard, ★★★ challenging. Batteries are ideal unless an internal resistance is given.

    Section 21.1 — Circuit Elements and Diagrams

    21.1 ★ How much work does a \(9.0\,\mathrm{V}\) battery do in moving \(0.25\,\mathrm{C}\) of charge from its negative terminal to its positive terminal?

    21.2 ★ [Real-world: phones.] A phone battery has an emf of \(3.7\,\mathrm{V}\) and a capacity of \(4000\,\mathrm{mAh}\). How much energy does it store, in joules and in watt-hours?

    21.3 ★★ [Conceptual.] Draw a circuit diagram for a flashlight with two batteries in series, a switch, and a bulb. Show where you would connect an ammeter to measure the bulb’s current, and a voltmeter to measure the voltage across the bulb.

    Section 21.2 — Kirchhoff’s Laws and the Basic Circuit

    21.4 ★ A \(6.0\,\mathrm{V}\) battery is connected in a single loop with a \(10\,\mathrm{\Omega}\) and a \(20\,\mathrm{\Omega}\) resistor. Use the loop rule to find the current and the potential difference across each resistor.

    21.5 ★★ A single loop contains a \(9.0\,\mathrm{V}\) battery, a \(1.5\,\mathrm{V}\) battery connected so as to oppose it, and resistors of \(5.0\,\mathrm{\Omega}\) and \(10\,\mathrm{\Omega}\). Find the current. What would it be if the \(1.5\,\mathrm{V}\) battery were turned around?

    21.6 ★★ Repeat Example 21.3 with \(\mathcal{E}_1 = 10\,\mathrm{V}\), \(\mathcal{E}_2 = 5.0\,\mathrm{V}\), \(R_1 = R_2 = 5.0\,\mathrm{\Omega}\), and \(R_3 = 10\,\mathrm{\Omega}\). Which battery, if either, is being charged? Find the potential of junction \(a\) relative to junction \(b\).

    21.7 ★★ [Conceptual.] In Example 21.3, three loops can be drawn, but only two loop equations were used. Show that the loop equation for the outer loop is the difference of the other two, and so contains no new information.

    21.8 ★★★ Explain why the loop rule would fail if the electric field in a circuit were not conservative, that is, if the work done by the field on a charge carried around a closed path were not zero. (Chapter 24 shows that a changing magnetic field produces exactly such a field, and the loop rule must then be modified.)

    Section 21.2.1 — Energy and Power in a Circuit

    21.9 ★★ In Example 21.2, the \(6.0\,\mathrm{V}\) battery is turned around so that the two batteries aid each other. Find the current and the power delivered or absorbed by each element, and check that the books balance.

    21.10 ★★ [Real-world: battery charging.] A charger forces a current of \(5.0\,\mathrm{A}\) into the positive terminal of a car battery whose emf is \(12.0\,\mathrm{V}\) and internal resistance \(0.10\,\mathrm{\Omega}\). (a) At what rate is energy stored in the battery? (b) At what rate is heat produced inside it? (c) What is the terminal voltage?

    Section 21.3 — Multiple Resistors in a Circuit: Series vs. Parallel

    21.11 ★ Find the equivalent resistance of \(10\,\mathrm{\Omega}\), \(20\,\mathrm{\Omega}\), and \(30\,\mathrm{\Omega}\) resistors (a) in series and (b) in parallel.

    21.12 ★ How many \(100\,\mathrm{\Omega}\) resistors must be connected in parallel to give an equivalent resistance of \(12.5\,\mathrm{\Omega}\)?

    21.13 ★★ Find the equivalent resistance between terminals \(a\) and \(b\) of the network below. If \(24\,\mathrm{V}\) is applied between \(a\) and \(b\), find the current in the \(12\,\mathrm{\Omega}\) resistor.

    A resistor network between an open terminal a on the left and an open terminal b on the right.Figure descriptionA resistor network between an open terminal a on the left and an open terminal b on the right. From a, a 6.0 ohm resistor leads to a junction. From that junction two branches run to a second junction: the upper branch contains a single 12 ohm resistor, and the lower branch contains a 4.0 ohm and an 8.0 ohm resistor in series. From the second junction a wire leads to terminal b.

    21.14 ★★ [Conceptual.] For the three bulbs of the checkpoint in Section 21.3 (\(A\) in series with the parallel pair \(B\) and \(C\)), with a \(12\,\mathrm{V}\) battery and bulbs of \(6.0\,\mathrm{\Omega}\) each, find the power in each bulb before and after \(C\) is removed. Do your numbers agree with your answers to the checkpoint?

    21.15 ★★ [Real-world: measurement.] A voltage divider consists of two \(10\,\mathrm{k\Omega}\) resistors across a \(9.0\,\mathrm{V}\) battery. (a) What is the voltage across each? (b) A voltmeter with a resistance of \(10\,\mathrm{k\Omega}\) is connected across one of the resistors. What does it read? (c) What would a voltmeter of resistance \(10\,\mathrm{M\Omega}\) read? Explain why a good voltmeter must have a very high resistance.

    21.16 ★★ [Real-world: household circuits.] A \(1500\,\mathrm{W}\) space heater, a \(1200\,\mathrm{W}\) hair dryer, and a \(100\,\mathrm{W}\) lamp are all plugged into outlets on the same \(120\,\mathrm{V}\) circuit, which has a \(15\,\mathrm{A}\) breaker. Find the total current. Does the breaker trip? What is the equivalent resistance of the three appliances?

    21.17 ★★★ Find the equivalent resistance between \(a\) and \(b\) of the infinite ladder of identical resistors \(R\) shown. (Hint: adding one more section to the front of an infinite ladder leaves it unchanged, so \(R_{\text{eq}} = R + (R \parallel R_{\text{eq}})\).)

    An infinite ladder network of identical resistors R.Figure descriptionAn infinite ladder network of identical resistors R. Two open terminals, a at top left and b at bottom left, begin a top wire and a bottom wire. Along the top wire, resistors R are repeated in series; after each one, a rung resistor R connects the top wire down to the bottom wire. Three sections are drawn, followed by dots indicating that the pattern continues forever.

    Section 21.4 — Ideal vs. Real Batteries

    21.18 ★ A battery with an emf of \(1.50\,\mathrm{V}\) and an internal resistance of \(0.30\,\mathrm{\Omega}\) is connected to a \(2.70\,\mathrm{\Omega}\) resistor. Find the current and the terminal voltage.

    21.19 ★★ [Graph-reading.] The graph shows the terminal voltage of a battery against the current it delivers.

    A graph of terminal voltage in volts, from 0 to 7, against current in amperes, from 0 to 3.Figure descriptionA graph of terminal voltage in volts, from 0 to 7, against current in amperes, from 0 to 3. The data form a straight line starting at 6.0 volts at zero current and falling to 4.0 volts at 2.0 amperes, continuing to 3.0 volts at 3.0 amperes.
    1. Find the emf and the internal resistance.
    2. What current would flow if the terminals were shorted?
    3. What load resistance would draw \(1.5\,\mathrm{A}\)?

    21.20 ★★ When a battery delivers \(2.0\,\mathrm{A}\), its terminal voltage is \(11.4\,\mathrm{V}\); when it delivers \(5.0\,\mathrm{A}\), its terminal voltage is \(10.5\,\mathrm{V}\). Find its emf and internal resistance.

    21.21 ★★ Four \(1.5\,\mathrm{V}\) cells, each with an internal resistance of \(0.20\,\mathrm{\Omega}\), are connected in series to light a \(4.0\,\mathrm{\Omega}\) bulb. Find the current, the power delivered to the bulb, and the power wasted inside the cells.

    21.22 ★★★ A battery of emf \(\mathcal{E}\) and internal resistance \(r\) drives a load \(R\). (a) Show that the efficiency, the fraction of the battery’s output delivered to the load, is \(R/(R + r)\). (b) Sketch the power to the load and the efficiency as functions of \(R/r\) on the same axes. (c) Explain why a power utility operates far from the condition of maximum power transfer.

    Section 21.5 — RC Circuits

    21.23 ★ [Conceptual.] Just after the switch is closed in a charging RC circuit, the capacitor acts like a plain wire; long afterward, it acts like a break in the circuit. Explain both statements using \(v = q/C\).

    Section 21.5.1 — Charging a Capacitor

    21.24 ★ A \(220\,\mathrm{\mu F}\) capacitor is charged through a \(4.7\,\mathrm{k\Omega}\) resistor. Find the time constant and the time needed to reach \(95\%\) of the final charge.

    21.25 ★★ An uncharged \(10\,\mathrm{\mu F}\) capacitor is charged through a resistor \(R\) by a \(12\,\mathrm{V}\) battery. Two seconds after the switch is closed, the voltage across the capacitor is \(8.0\,\mathrm{V}\). Find \(R\).

    21.26 ★★ [Real-world: timing circuits.] In an intermittent windshield wiper, a \(100\,\mathrm{\mu F}\) capacitor charges from a \(9.0\,\mathrm{V}\) supply through a resistor, and the wiper sweeps when the capacitor’s voltage reaches \(5.0\,\mathrm{V}\). What resistance gives a \(4.0\,\mathrm{s}\) delay?

    21.27 ★★ Show that a charging capacitor holds a quarter of its final energy at the moment \(t = RC\ln 2\).

    Section 21.5.2 — Discharging a Capacitor

    21.28 ★ A \(1000\,\mathrm{\mu F}\) capacitor charged to \(12\,\mathrm{V}\) discharges through a \(100\,\mathrm{\Omega}\) resistor. Find the initial current, the time constant, and the charge remaining after \(0.25\,\mathrm{s}\).

    21.29 ★★ [Graph-reading.] The graph shows the voltage across a capacitor as it discharges through a resistor.

    A graph of capacitor voltage in volts, from 0 to 10, against time in seconds, from 0 to 8.Figure descriptionA graph of capacitor voltage in volts, from 0 to 10, against time in seconds, from 0 to 8. The curve starts at 10 volts at time zero and decays exponentially, passing about 3.7 volts at 2 seconds, about 1.4 volts at 4 seconds, and approaching zero by 8 seconds.
    1. Estimate the time constant from the graph, in two ways: from the time for the voltage to fall to \(36.8\%\) of its initial value, and from its half-life.
    2. If the capacitance is \(50\,\mathrm{\mu F}\), what is the resistance?
    3. What was the initial current?

    21.30 ★★★ [Real-world: electronics.] No insulator is perfect, so a charged capacitor slowly discharges through its own dielectric. A parallel-plate capacitor is filled with a dielectric of dielectric constant \(\kappa\) and resistivity \(\rho\). (a) Show that its self-discharge time constant is \(\tau = \kappa\epsilon_0\rho\), independent of the plates’ area and spacing. (b) Evaluate \(\tau\) for glass, with \(\kappa = 5.0\) and \(\rho = 1.0\times10^{12}\,\Omega\cdot\mathrm{m}\).

    21.31 ★★★ A \(12\,\mathrm{V}\) battery is connected in series with a \(4.0\,\mathrm{\Omega}\) resistor \(R_1\) and a parallel pair consisting of an \(8.0\,\mathrm{\Omega}\) resistor \(R_2\) and an uncharged \(5.0\,\mathrm{\mu F}\) capacitor. (a) What is the current through the battery just after the circuit is connected? (b) What is it long afterward, and what is the charge on the capacitor then? (c) The battery is then disconnected, leaving the capacitor connected across \(R_2\) alone. Find the time constant of the discharge.

    21.32 ★★★ Kirchhoff’s rules can be checked against the result for resistors in parallel. Two resistors \(R_1\) and \(R_2\) in parallel are connected to a battery of emf \(\mathcal{E}\) and internal resistance \(r\). Use the junction and loop rules, without using equation (21.6), to find the current through each resistor, and show that your result agrees with replacing the pair by \(R_1R_2/(R_1 + R_2)\).


    This page titled 21.E: DC Circuits (Problems) was last modified on Thu, 12 Nov 2026 04:26:45 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.