1.4: Unit Conversions

Physics: A Foundation for Scientists and Engineers · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    1.4: Unit Conversions

    Many calculations require converting a quantity from one unit to another: between SI prefixes (km to nm), between SI and non-SI units (meters to inches), or between compound units (Mm/s to mi/hr). The systematic technique is to multiply by one or more conversion factors: ratios equal to \(1\) that are constructed from known equivalences.

    The conversion-factor method

    If \(1\,\mathrm{m} = 100\,\mathrm{cm}\), then both \(\dfrac{100\,\mathrm{cm}}{1\,\mathrm{m}}\) and \(\dfrac{1\,\mathrm{m}}{100\,\mathrm{cm}}\) equal \(1\). Multiplying any quantity by either of these does not change its value, only how it is expressed. The trick is to choose the orientation that makes the unwanted unit cancel, leaving the unit you want.

    Example 1.2: A simple length conversion

    How many inches are in \(4.2\,\mathrm{m}\)? Use the equivalence \(1\,\mathrm{m} = 3.28\,\mathrm{ft}\) and \(1\,\mathrm{ft} = 12\,\mathrm{in}\).

    Solution

    Chain two conversion factors so that meters and feet both cancel:

    \[4.2\,\cancel{\mathrm{m}} \times \frac{3.28\,\cancel{\mathrm{ft}}}{1\,\cancel{\mathrm{m}}} \times \frac{12\,\mathrm{in}}{1\,\cancel{\mathrm{ft}}} = (4.2)(3.28)(12)\,\mathrm{in}.\]

    The meters cancel against the first ratio, the feet cancel against the second, and the only unit left is inches. Always check the cancellation before reaching for the calculator: if the wrong units survive, the conversion factors are upside down.

    The arithmetic can be done one factor at a time: \(4.2 \times 3.28 = 13.776\) (the length in feet), and \(13.776 \times 12 = 165.3\) (the length in inches).

    Now apply the significant-figure rules. The \(12\) is exact (a foot is defined as twelve inches), so it imposes no limit, and \(3.28\) has three figures. The measured length \(4.2\,\mathrm{m}\) has only two, so the answer keeps two:

    \[165.3\,\mathrm{in} \;\longrightarrow\; 1.7 \times 10^{2}\,\mathrm{in}.\]

    Writing “\(170\,\mathrm{in}\)” would leave the reader unsure whether the zero is significant; scientific notation says two figures unambiguously.

    Example 1.3: Football field in inches

    How long, in inches, is a standard American football field, measured from goal line to goal line (\(100\) yards)? (Including the two end zones the field is \(120\) yards long.)

    Solution

    Use \(1\,\mathrm{yd} = 3\,\mathrm{ft}\) and \(1\,\mathrm{ft} = 12\,\mathrm{in}\):

    \[100\,\cancel{\mathrm{yd}} \times \frac{3\,\cancel{\mathrm{ft}}}{1\,\cancel{\mathrm{yd}}} \times \frac{12\,\mathrm{in}}{1\,\cancel{\mathrm{ft}}} = 3600\,\mathrm{in}.\]

    Converting between SI prefixes

    Conversions between prefixed SI units follow the same pattern; the conversion factor is simply a power of ten read off the prefix table.

    Example 1.4: 140 km to nm

    Convert \(140\,\mathrm{km}\) to nanometers.

    Solution

    Step 1: Build the conversion factors. The prefix table gives \(1\,\mathrm{km} = 10^{3}\,\mathrm{m}\) directly. It gives nano- as \(10^{-9}\), which means \(1\,\mathrm{nm} = 10^{-9}\,\mathrm{m}\). We want the factor the other way around (meters in terms of nanometers), so multiply both sides by \(10^{9}\):

    \[10^{9} \times (1\,\mathrm{nm}) = 10^{9} \times (10^{-9}\,\mathrm{m}) \quad\Longrightarrow\quad 1\,\mathrm{m} = 10^{9}\,\mathrm{nm},\]

    since \(10^{9} \times 10^{-9} = 10^{9 + (-9)} = 10^{0} = 1\).

    Step 2: Chain them. Orient each factor so the unwanted unit cancels:

    \[140\,\cancel{\mathrm{km}} \times \frac{10^{3}\,\cancel{\mathrm{m}}}{1\,\cancel{\mathrm{km}}} \times \frac{10^{9}\,\mathrm{nm}}{1\,\cancel{\mathrm{m}}} = 140 \times 10^{3} \times 10^{9}\,\mathrm{nm}.\]

    When powers of ten are multiplied, their exponents add: \(10^{3} \times 10^{9} = 10^{3+9} = 10^{12}\).

    Step 3: Put the result in scientific notation. \(140 \times 10^{12}\) is correct but not in standard form, because \(140\) is not between \(1\) and \(10\). Write \(140 = 1.4 \times 10^{2}\) and add the exponents again:

    \[140 \times 10^{12}\,\mathrm{nm} = 1.4 \times 10^{2} \times 10^{12}\,\mathrm{nm} = 1.4 \times 10^{14}\,\mathrm{nm}.\]

    Check. A nanometer is an extremely small unit, so it should take an enormous number of them to span \(140\,\mathrm{km}\). It does.

    Example 1.5: 208 ps to Ts

    Convert \(208\,\mathrm{ps}\) to teraseconds.

    Solution

    From the prefix table, \(1\,\mathrm{ps} = 10^{-12}\,\mathrm{s}\) and \(1\,\mathrm{Ts} = 10^{12}\,\mathrm{s}\). Because seconds must cancel, the second factor has seconds on the bottom:

    \[208\,\cancel{\mathrm{ps}} \times \frac{10^{-12}\,\cancel{\mathrm{s}}}{1\,\cancel{\mathrm{ps}}} \times \frac{1\,\mathrm{Ts}}{10^{12}\,\cancel{\mathrm{s}}} = 208 \times \frac{10^{-12}}{10^{12}}\,\mathrm{Ts}.\]

    When one power of ten is divided by another, the exponents subtract:

    \[\frac{10^{-12}}{10^{12}} = 10^{-12-12} = 10^{-24}.\]

    Watch the signs: it is tempting to see \(-12\) and \(12\) and conclude that they cancel to \(10^{0}\), but that would be true only if we were multiplying. Finally, write \(208 = 2.08 \times 10^{2}\) to reach standard form:

    \[208 \times 10^{-24}\,\mathrm{Ts} = 2.08 \times 10^{2} \times 10^{-24}\,\mathrm{Ts} = 2.08 \times 10^{-22}\,\mathrm{Ts}.\]

    Check. A picosecond is a very short time, and a terasecond is a very long one: a year is about \(3.16 \times 10^{7}\,\mathrm{s}\), so \(1\,\mathrm{Ts} = 10^{12}\,\mathrm{s} \div (3.16 \times 10^{7}\,\mathrm{s/yr}) \approx 31\,700\) years. It makes sense that the numerical answer is tiny.

    Converting units raised to powers

    Two panels comparing area and volume scaling.
    Figure 1.2. Why a conversion factor must be raised to the same power as its unit. Dividing each edge into ten parts produces \(10^2\) small squares and \(10^3\) small cubes, not ten of either; one of each is shaded. The same argument with \(100\) divisions per edge (centimeters instead of decimeters) gives \(1\,\mathrm{m^2} = 10^4\,\mathrm{cm^2}\) and \(1\,\mathrm{m^3} = 10^6\,\mathrm{cm^3}\). As a bonus, one of the small cubes on the right is a cubic decimeter, better known as a liter.
    Figure descriptionTwo panels comparing area and volume scaling. The left panel shows a square with each edge divided into ten equal parts, forming a ten-by-ten grid of one hundred small squares, with a single small square in the corner shaded gold. The right panel shows a cube drawn in perspective with each edge likewise divided into ten, containing one thousand small cubes, with one small cube shaded. Dividing every edge into ten parts yields ten squared small squares and ten cubed small cubes, not ten of either.

    When the unit being converted is squared, cubed, or otherwise raised to a power, the conversion factor must be raised to the same power. This is the single most common source of error in this chapter, and it is worth seeing geometrically rather than algebraically. Figure 1.2 shows why: a square meter is not \(100\) square centimeters but \(100 \times 100\) of them, and a cubic meter is not \(100\) cubic centimeters but \(100 \times 100 \times 100\).

    Example 1.6: Area conversion

    Convert \(14\,\mathrm{m^2}\) to square centimeters.

    Solution

    Step 1: Square the length equivalence. Start from \(1\,\mathrm{m} = 100\,\mathrm{cm}\) and square both sides. The exponent applies to everything inside the parentheses, the number and the unit, just as \((ab)^2 = a^2b^2\):

    \[(1\,\mathrm{m})^2 = (100\,\mathrm{cm})^2 \quad\Longrightarrow\quad 1\,\mathrm{m^2} = 100^2\,\mathrm{cm^2} = 10\,000\,\mathrm{cm^2}.\]

    In powers of ten, \(100^2 = (10^{2})^{2} = 10^{4}\).

    Step 2: Convert. \[14\,\cancel{\mathrm{m^2}} \times \frac{10^{4}\,\mathrm{cm^2}}{1\,\cancel{\mathrm{m^2}}} = 14 \times 10^{4}\,\mathrm{cm^2} = 1.4 \times 10^{5}\,\mathrm{cm^2},\]

    where the last step writes \(14 = 1.4 \times 10^{1}\) and adds exponents.

    The common mistake. Using the unsquared factor gives \(14 \times 100 = 1400\,\mathrm{cm^2}\), which is too small by a factor of \(100\). The quick test: did the unit \(\mathrm{m^2}\) actually cancel? With the factor \(100\,\mathrm{cm}/1\,\mathrm{m}\) it would not; you would be left with \(\mathrm{m \cdot cm}\).

    Example 1.7: Volume conversion

    Convert \(4.19 \times 10^{24}\,\mathrm{mm^3}\) to cubic megameters.

    Solution

    Step 1: Cube the length equivalences. From the prefix table, \(1\,\mathrm{mm} = 10^{-3}\,\mathrm{m}\) and \(1\,\mathrm{Mm} = 10^{6}\,\mathrm{m}\). Cube both sides of each, remembering that the cube applies to the number and the unit. A power of a power multiplies the exponents, \((10^{a})^{b} = 10^{ab}\):

    \[\begin{aligned}1\,\mathrm{mm^3} &= (10^{-3}\,\mathrm{m})^3 = 10^{(-3)(3)}\,\mathrm{m^3} = 10^{-9}\,\mathrm{m^3}, \\ 1\,\mathrm{Mm^3} &= (10^{6}\,\mathrm{m})^3 = 10^{(6)(3)}\,\mathrm{m^3} = 10^{18}\,\mathrm{m^3}.\end{aligned}\]

    Step 2: Chain the factors. Go from \(\mathrm{mm^3}\) to \(\mathrm{m^3}\), then from \(\mathrm{m^3}\) to \(\mathrm{Mm^3}\):

    \[4.19 \times 10^{24}\,\cancel{\mathrm{mm^3}} \times \frac{10^{-9}\,\cancel{\mathrm{m^3}}}{1\,\cancel{\mathrm{mm^3}}} \times \frac{1\,\mathrm{Mm^3}}{10^{18}\,\cancel{\mathrm{m^3}}} = 4.19 \times \frac{10^{24} \times 10^{-9}}{10^{18}}\,\mathrm{Mm^3}.\]

    Step 3: Collect the powers of ten. Exponents in the numerator add; the exponent in the denominator subtracts:

    \[\frac{10^{24} \times 10^{-9}}{10^{18}} = 10^{24 + (-9) - 18} = 10^{-3}, \qquad\text{so}\qquad 4.19 \times 10^{24}\,\mathrm{mm^3} = 4.19 \times 10^{-3}\,\mathrm{Mm^3}.\]

    Check. The number went from \(10^{24}\) to \(10^{-3}\), a drop of \(27\) powers of ten. That is exactly the ratio of the two volume units: a megameter is \(10^{9}\) millimeters, so a cubic megameter is \((10^{9})^{3} = 10^{27}\) cubic millimeters.

    Converting compound units

    When a quantity has multiple units (a speed in meters per second, a density in grams per cubic centimeter), convert each unit separately. It’s often clearest to lay every conversion factor out as a chain.

    Example 1.8: Speed conversion

    Convert \(45\,\mathrm{Mm/s}\) to miles per hour, using \(1\,\mathrm{mi} = 1609\,\mathrm{m}\) and \(1\,\mathrm{hr} = 3600\,\mathrm{s}\).

    Solution

    Step 1: Convert the numerator and the denominator separately. The length unit is on top, so its factors must put \(\mathrm{Mm}\) on the bottom and then \(\mathrm{m}\) on the bottom. The time unit is on the bottom of \(\mathrm{Mm/s}\), so to cancel it the time factor must put seconds on the top: \(3600\,\mathrm{s}/1\,\mathrm{hr}\), not \(1\,\mathrm{hr}/3600\,\mathrm{s}\).

    \[\begin{aligned}45\,\frac{\cancel{\mathrm{Mm}}}{\cancel{\mathrm{s}}} \times \frac{10^{6}\,\cancel{\mathrm{m}}}{1\,\cancel{\mathrm{Mm}}} \times \frac{1\,\mathrm{mi}}{1609\,\cancel{\mathrm{m}}} \times \frac{3600\,\cancel{\mathrm{s}}}{1\,\mathrm{hr}} &= \frac{45 \times 10^{6} \times 3600}{1609}\,\frac{\mathrm{mi}}{\mathrm{hr}}.\end{aligned}\]

    It makes physical sense that converting “per second” to “per hour” multiplies by \(3600\): in an hour the object covers \(3600\) times the distance it covers in a second.

    Step 2: Do the arithmetic. The numerator is \(45 \times 3600 = 162\,000 = 1.62 \times 10^{5}\), so \(45 \times 10^{6} \times 3600 = 1.62 \times 10^{5} \times 10^{6} = 1.62 \times 10^{11}\). Dividing,

    \[\frac{1.62 \times 10^{11}}{1609} = 1.007 \times 10^{8}\,\mathrm{mi/hr} \approx 1.0 \times 10^{8}\,\mathrm{mi/hr},\]

    rounded to two significant figures to match the \(45\).

    Check. Light travels \(c = 3.00 \times 10^{8}\,\mathrm{m/s} = 300\,\mathrm{Mm/s}\), which the same chain of conversions turns into about \(6.7 \times 10^{8}\,\mathrm{mi/hr}\). Our object is moving at \(45/300 = 0.15\) of that, and \(0.15 \times 6.7 \times 10^{8} \approx 1.0 \times 10^{8}\,\mathrm{mi/hr}\). The answer survives the check.

    Example 1.9: Filling a swimming pool

    How long will it take to fill an Olympic swimming pool of dimensions \(50\,\mathrm{m} \times 25\,\mathrm{m} \times 2\,\mathrm{m}\) from a garden hose delivering \(15\) gallons per minute? Use \(1\,\mathrm{m^3} = 264.172\,\mathrm{gal}\).

    Solution

    Step 1: Find the volume. For a rectangular box, volume is length times width times depth:

    \[V = (50\,\mathrm{m})(25\,\mathrm{m})(2\,\mathrm{m}) = 2500\,\mathrm{m^3}.\]

    Step 2: Put the volume in the hose’s units. The flow rate is in gallons, so convert:

    \[V = 2500\,\cancel{\mathrm{m^3}} \times \frac{264.172\,\mathrm{gal}}{1\,\cancel{\mathrm{m^3}}} = 660\,430\,\mathrm{gal} \approx 6.60 \times 10^{5}\,\mathrm{gal}.\]

    Step 3: Solve for the time. A flow rate is volume delivered per unit time, \(R = V/t\). We want \(t\), so multiply both sides by \(t\) and then divide both sides by \(R\):

    \[R = \frac{V}{t} \quad\Longrightarrow\quad Rt = V \quad\Longrightarrow\quad t = \frac{V}{R}.\]

    Substituting,

    \[t = \frac{6.60 \times 10^{5}\,\mathrm{gal}}{15\,\mathrm{gal/min}} \approx 4.40 \times 10^{4}\,\mathrm{min}.\]

    The units work out because dividing by a fraction is the same as multiplying by its reciprocal: \(\mathrm{gal} \div (\mathrm{gal}/\mathrm{min}) = \mathrm{gal} \times (\mathrm{min}/\mathrm{gal}) = \mathrm{min}\). If you had divided the other way, the units would have come out as \(1/\mathrm{min}\): a sure sign of an error.

    Step 4: Express the answer in sensible units. Tens of thousands of minutes is hard to picture, so convert to days:

    \[4.40 \times 10^{4}\,\cancel{\mathrm{min}} \times \frac{1\,\cancel{\mathrm{hr}}}{60\,\cancel{\mathrm{min}}} \times \frac{1\,\mathrm{day}}{24\,\cancel{\mathrm{hr}}} \approx 31\,\mathrm{days}.\]

    A garden hose running continuously for a month would just barely do it, which is why pools are filled from water mains, not hoses.


    This page titled 1.4: Unit Conversions was last modified on Thu, 12 Nov 2026 04:26:52 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.