Chapter 3: Electricity

Lighting for Digital Film · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    Chapter 3: Electricity

    Electrocution is a clear and present danger when working with high-wattage lights on sets. A “baby” or 1K has 1,000 watts in its housing. We are not turning students into electricians, but knowledge about wiring and how to calculate load safely is the goal of this chapter. Consequently, this section reviews electrical wiring, so students know the hot, neutral, and ground wires regardless of the color differentiation. To establish the load, using the West Virginia formula is important so students can calculate how many lights can be safely plugged into one circuit, even if they are filming in a foreign land.

    At the end of the chapter is a short group discussion exercise to review the different variations of hot, ground, and neutral wires.

    A circular sign on a brick wall. It reads, "WESTMINSTER CITY COUNCIL: SAVOY THEATRE."
    Figure 3.1. Opened in 1881 the Savoy Theatre was the first public building in the world to be lit throughout by electricity.

    In 1881, electricity powered the Savoy theater’s lights in London, England.[1] This same year in Paris, France, the International Congress of Electricians convened at the first International Exposition of Electricity. This conference debated electrical standards from an international perspective. At that time, they gave recommendations for standard electrical nomenclature: the “ampere, volt, and ohm, as practical units for current, pressure (voltage), and resistance.”[2] These terms achieved legal status 12 years later at the Chicago Columbian World Exhibition in 1893,[3] and this codification continues today, with an additional unit called wattage.

    Wattage (watts) is the measure of the power of a lighting instrument and is shown by the letter W. For example, a bedside lamp in the home is around 60 W to 100 W. On a film set our lights vary from, e.g., 150 W, 300 W, 650 W, 1,000 W, 2,000 W and more. Imagine you are watering your garden. Wattage is the faucet controlling the water for the hose. The more you turn the faucet on, the more water gets into the hose.

    The ampere (amp) is a unit of constant electrical current. The amperage is the strength of the electromagnetic force between two electrical conductors, i.e., the measurement of the electrical current. A basic household circuit contains 15 amps, i.e., the amount of electricity running through a circuit. In modern homes, and particularly larger appliances, e.g., refrigerators have 20 or 30 amps. Think of that garden hose with water running through it as the amps.

    A circuit is a closed loop that allows electricity to flow to a device. The circuit is the piping that allows the water to get to the faucet for the garden hose. There are two types of circuits: the direct current, aka DC, that allows an electrical charge to flow in one direction. For example, batteries, generators.[4] The alternating current, AC, allows the charge to flow periodically in both directions.[5]

    A standard US three pronged electrical outlet.
    Figure 3.2. Household circuit.

    Voltage is the force behind the flow of electronics, or in other words the measurement of the electrical power in the outlet. The normal household voltage in the USA is 120 V. If you are in the UK, this voltage is 220 V. However, our high voltage film studios have 240 V. Volts are the water pressure in the hose. So high voltage is high pressure.

    Ohm is the resistance against the flow of the current. Think of the size of the garden hose. Decreasing the size of the hose means decreasing the flow of the water.

    Materials that conduct electricity, allowing it to flow freely, are called conductors; one common example is copper. Materials like plastic and rubber which prevent electricity from passing through them are insulators. Working on a set, the crew should be wearing rubber-soled footwear. This nonconductive material has a small level of protection by preventing the wearers’ feet from completing an electrical circuit to the ground.

    An old photograph of a man in a suit with spectacles. It reads at the bottom: "J. H. HALLBERG."
    Figure 3.3. Josef Henrik Hallberg.

    The earliest analogy comparing electricity with water hoses and pipes comes from Swedish-born Josef Hallberg, who moved to the USA in 1890. He became an electrical engineer with the General Incandescent Art Light Company and was an associate member of the American Institute of Electrical Engineers. Hallberg developed a “complete line of modern enclosed arc lamps, alternating-current regulators, automatic transformers, switchboards, and protecting devices. He has also engineered many important street lighting installations, the most notable of which is the street lighting system in Cincinnati, OH.”[6]

    Cross section of an electric meter reader
    Figure 3.4. Josef Henrik Hallberg’s meter reader.

    Hallberg became interested in the burgeoning motion picture industry, particularly the electricity for picture houses. In 1908 he was granted a patent on his electric “Economizer” and was allowed to name arc lamps, special terminals, and connections for use in picture houses.[7] In his book, Motion Picture Electricity he states,

    Voltage is the word which signifies the pressure of the electric current on or in an electric circuit. Suppose you have a water pipe one mile long and at the end of it there is a faucet and just ahead of the faucet a water pressure gauge is connected to the pipe, and the gauge indicates no pounds. Now open the faucet and you will see that the pressure gauge needle will fall back, depending upon the size of the pipe and how wide you open the faucet. If the pipe is small, the friction the water creates in flowing against the pipe wall will cause the pressure at the end to drop very low.[8]

    An electric meter surrounded by nature set up against a brick wall.
    Figure 3.5. Modern electrical meter

    He continues his water pipe analogy with the following:

    Ampere is the word which signifies the quantity or volume of electricity flowing through an electric circuit, arc lamp, incandescent lamp, motor or other machine, connected to the circuit. The measurement called “gallon” in the water system, or cubic foot for gas, designates quantity or volume. So does the ampere in the electric system.[9]

    Figure 3.4 shows an early example of his electrical meter reader. When you look at the modern meter reader in figure 3.5, you can see that little has changed over the years.

    West Virginia Formula

    The ability to count amperage is the most basic tool required as a spark on set. Your production relies on it and is a potential safety hazard. (see Chapter 2, SOS). The 1st AD and relevant heads of department should discuss hazards, conduct and record risk assessments, and conduct regular safety meetings to ensure people are clear on how to stay safe. Calculating how many lights can safely be used on one circuit needs some math, but you do not need a calculator. Ohm’s law sounds professional and scary if you are like me, afraid of math. I use the West Virginia Formula—as it is easier for me to remember the state initials WV and the letter A.

    The letter W corresponds to watts, i.e., power of the light (e.g., 1,000 watts). The letter V is for voltage (e.g., 220 volts), and letter A equals amps, the current (e.g., 10 amps). Hence, wattage = voltage multiplied by amps. W=VA.

    So let us do some math. How many babies (1000 watts) can fit into one household socket (110 volts) using 20 amps in the US?

    W = VA (Watts = Voltage x Amps)

    1,000 watts = 110 volts x 20 amps = 1,000 divided by 2,200 = 2.2 babies.

    You can err on the side of caution by using 2 babies and you still have 200 watts left over.

    You can also calculate how many amps would be needed for 1 light.

    A = W/V (amps = watts divided by volts)

    1,000 watts divided by 110 volts = amps needed = 11 amps.

    Transmission Lines

    Electricity is generated by various sources, including nuclear, gas, hydroelectricity, solar, wind, and coal. For our homes, these power stations supply energy via a substation, a transformer, the household circuit breaker, and the circuit.

    Giant electrical equipment with wires attaching them all.
    Figure 3.6. Substation, Smeaton.
    A giant power station.
    Figure 3.7. Gateway Generating Station

    Transformer

    The transformer is on a pole mounted outside buildings, e.g., 34,000 volts. It has a transmission (distribution) line snaking into the building and transforms the voltage to 110 V (e.g., USA), or 220 V (e.g., UK), or even 240 V (high volt studios).

    A pole with an electrical wire.
    Figure 3.8. Single-Phase Pole Transformer.
    A digital electric meter mounted on a white wall
    Figure 3.9. Electric board from transmission line into building.
    A circuit breaker in a wall.
    Figure 3.10. Each breaker should be clearly labeled.

    Circuit Breaker

    This distributes electricity into separate circuits in the home, such as the bathroom, living room, bedroom, etc. A modern breaker should have each circuit clearly labeled. Always examine the circuit breaker in each location you are shooting in, make detailed notes, and take a picture of what room is connected to what circuit. For example, if the box says bathroom and living room, this means these two rooms are on one circuit. So, you could not run two babies in the bathroom and two babies in the living room without overloading the circuit.

    A plug for an outlet, shot so one can see the three prongs that stick into the outlet.
    Figure 3.11. Three-pronged plug.

    How Electricity is Connected and Wired

    Connections

    The National Electrical Manufacturers Association (NEMA) sets safety standards and standardizes electrical connectors used to connect power cords to electrical outlets for electrical plugs used in North America. These have defined configurations to prevent hazards and ensure electrical safety. In the USA, the basic standard connector (plug) has three prongs with 15 amps.

    NEMA also has locking connectors, a twist-lock system that is a main feature of stage lighting and high-voltage studio systems. They are created so they cannot be accidentally pulled out of the socket. A 20-amp plug has a longer prong on one side, so you are unable to put a 20-amp into a 15-amp connector socket. They must be put into a twist and lock receptacle. These are also called Edison plugs.

    A 20-amp plug which is round and has the prongs pointing in different directions.
    Figure 3.12. A 20-amp plug.
    A twist and lock receptacle. It just looks like an outlet but with a mechanism visible on the edges.
    Figure 3.13. Twist and lock receptacle.
    A three-prong electrical outlet and light switch.
    Figure 3.14. GFCI-ground fault circuit interrupters.

    A Ground Fault Circuit Interrupter is an electrical device that protects against electric shock, burns, and electrocution. It works by comparing the amount of electricity flowing in and out of a circuit. It quickly shuts off the power if there is an imbalance. They are typically installed in areas where water and electricity are close together, such as in kitchens, bathrooms, and outdoors.

    Wiring

    In the USA, all connectors contain two or three color-coded wires. Other countries may differ slightly (e.g., all plugs in the UK have three wires), and if you are shooting in a foreign country, you should discover their electrical norms ahead of time.

    • Hot (black) live, aka hot leg, runs into the service panel.
    • Neutral (white) is run from the white center tap wire.
    • Ground (copper or brown) ties into earth. Sockets are polarized (one blade slightly wider than the other) so it can only be inserted one way.
    Four wires broken off at the ends in four different colors of plastic casing.
    Figure 3.15. Color-coded electrical wires

    Take care, however, as international colors are usually:

    • Hot – red
    • Neutral – blue
    • Ground – yellow/green

    Wire color codes are different across regions.

    I come from Scotland, UK, which follows the European system. So not only are the wires different colors from the USA or Australia, but the voltage is different. UK homes contain 220 volts in a circuit, so our electrical plugs are all three prongs with amps that we change out when needed. Even a toaster has three prongs.

    A CGFI circuit. It is a tied-together cable with charger items on either end, but one clearly is meant to plug into other parts and the other is meant to be the part a plug goes into.
    Figure 3.16. High-quality stinger.

    Extension Cords

    “Can I have a 25-foot stinger?”

    The nickname for an extension cord is a stinger. However, unlike a regular extension cord, a stinger consists of industry-standard, high-quality cable and can carry the whole amp requirement of industry lighting and tools. The amperage rating of a film industry stinger matches the maximum amperage rating of a 20-amp electrical safety breaker switch. Extension cords purchased at a local hardware store are often only rated for 15 amps, so the gauge is smaller.

    At the ends of the extension cord above are male and female plugs, aka Edison plugs. These are constructed with high-quality plastic that is extremely important for safe and extended conductivity of electricity. They are also strong enough to withstand the constant unwrapping, use, and re-wrapping for storage and transportation.

    Normally 25- or 50-foot-long, stingers are typically black to avoid reflected light spilling onto the set. It is made up of 12/3 wire, which refers to the gauge (diameter), i.e., 12 gauge, and the number of wires, i.e., hot, neutral, and ground. It is a heavier gauge than what you would use at home since it can handle 20 amps.

    The bigger the gauge number, the narrower the gauge, and consequently, the less amperage it can carry. (rule of opposites again). Stay away from bargain 16-gauge. Use 25- or 50-foot 14-gauge cables. If you need more than 50 feet, then use 12-gauge cables. If using a generator, use 10-gauge! If over 150 feet use an 8! Below gives an outline of what gauge to use depending on.

    Summary

    Electrical transmission comes from the power station, into the substation, through the transformer, and into the house circuits via the board and circuit breaker. NEMA safety plugs, connectors, and cables are all designed to carry electrical current as safely as possible. This chapter helps students to understand how plugs are wired, the related colors, and how to safely calculate load. If the crew are always on the lookout for electrical hazards and take the appropriate precautions to reduce the likelihood of serious accidents, then people will remain safe.

    Chapter Review

    Group Exercise

    In small groups of two or three, read and discuss the review section below. When you reach the five questions, try to answer them and discuss them with your group.

    Review: Hot wires carry power (voltage) from the electrical panel to its destination. A ground wire carries electricity to the ground during an abnormal electric current. Electronic switches require a tiny amount of constant electricity, so a neutral wire is required to run to them. Neutral wires carry electricity back to the electrical panel.

    Figuring out what wire color does is an effortless process if you remember basic colors. Let us begin with red, white, and brown.

    • Red is the hot or live wire carrying the electrical current—think of red as meaning danger.
    • White is the neutral wire—think of waving a white flag for a truce/neutrality.
    • Brown is the ground wire—think of brown earth in the garden.

    From those colors, you might have variations such as black, orange, blue, yellow, copper, green and yellow, and even gray. Some homes that are older have older style colors, so this is why it is important to be able to figure out what a “weird” one means.

    • If you think that a live wire signifies danger, then you can figure out that the red wire is a live wire.
    • Orange is also a warning sign, so it is a live wire.
    • Blue is the color of the sun (remember your kelvin’s blue = outdoor light), so another hot wire. However, there are some occasions when this is a neutral color, so you must figure out the other two wires to see if it is really a hot wire.
    • Black is death, so it is a hot wire.
    • Copper is shiny brown, so in essence, it is the ground wire.
    • Green is the color of grass. Grass is in the earth, so it is a ground wire too.
    • Green with a yellow stripe is still like an earth color, so it is a ground wire.
    • White is a neutral wire—it still carries an electrical current.
    • Gray is almost white, so a neutral wire still carries an electrical current.

    Questions to discuss in the group:

    1. I open up a plug and find a blue wire, a white wire, and a brown wire. What wires are live, ground, and neutral?
    2. I open the plug and find a red, white, and green wire. What wires are live, ground, and neutral?
    3. I open the plug and find a blue, white, and yellow/green wire. What wires are live, ground, and neutral?
    4. I open the plug and find orange, white, and copper wire. What wires are live, ground, and neutral?
    5. I open the plug and find a red, green, and gray wire. What wires are live, ground, and neutral?

    Interactive Quiz

    Media Attributions


    1. Dufford, Stanley, et al. “Stagecraft: Electrification.” Encyclopaedia Britannica, 2 Aug. 2022, https://www.britannica.com/art/stage...lectrification. Accessed 10 Nov. 2024. 1.03: Electricity#return-footnote-31-1
    2. Beauchamp, D. E. K. History of Technology Series 21: Exhibiting Electricity. Institution of Electrical Engineers, 1997. 1.03: Electricity#return-footnote-31-2
    3. Ibid., p. 161. 1.03: Electricity#return-footnote-31-3
    4. The Editors of Encyclopaedia Britannica. “Direct Current.” Encyclopaedia Britannica, 28 Aug. 2024, https://www.britannica.com/science/direct-current. Accessed 10 Nov. 2024. 1.03: Electricity#return-footnote-31-4
    5. The Editors of Encyclopaedia Britannica. “Alternating Current.” Encyclopaedia Britannica, 25 Sept. 2024, https://www.britannica.com/science/a...nating-current. Accessed 10 Nov. 2024. 1.03: Electricity#return-footnote-31-5
    6. Hallberg, Josef Henrik. Motion Picture Electricity. 1914. Internet Archive, https://archive.org/details/motionpictureele00hall. Accessed 10 Nov. 2024. 1.03: Electricity#return-footnote-31-6
    7. Ibid., p. 2. 1.03: Electricity#return-footnote-31-7
    8. Ibid., p. 10-11. 1.03: Electricity#return-footnote-31-8
    9. Ibid., p. 12. 1.03: Electricity#return-footnote-31-9

    This page titled Chapter 3: Electricity was last modified on Mon, 26 Oct 2026 17:17:02 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Roslin Smith via source content that was edited to the style and standards of the LibreTexts platform.