Chapter 5: Types of Lighting Instruments

Lighting for Digital Film · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    Chapter 5: Types of Lighting Instruments

    There are hundreds of lighting instruments to choose from. Technical and aesthetic demands will determine the correct fixtures, and no project is ever the same. This chapter covers the four main light sources: tungsten, tungsten-halogen, LEDs, and HMIs, and three types of light fixtures: open-faced, PAR, and lensed instruments. Different configurations of film industry lighting instruments, such as the Tota-Lite, Sky panels, and M18, are discussed. The pros and cons of the sources and fixtures, along with jargon such as tweenies, seniors, and kickers, are explained. Diagrams will show the main elements of lighting instruments, such as the housing, yolk, bulb, filament, sled, and reflector. Xenon, Metal-Halide and High Efficiency Plasma (HEP) are uncommon light technologies, so they are not covered in this chapter. However, tungsten, tungsten-halogen, LEDs, fluorescent, and HMIs are the main types of light bulbs used on film sets today.

    Close up

    How to choose your light:

    • Output: Determine the amount of light, color, temperature, and quality needed for the project.
    • Power source: Determine whether mains, electricity, batteries, or generators are required.
    • Portability and size: Consider lights’ size, weight, portability, and ease of use.
    • Budget: Know your budget and balance light features with affordability.
    • Reputation and brand: Pick reputable brands. Cheap unknowns can let you down and ultimately cost more money in the long run.
    A tungsten light bulb, lit up in the dark.
    Figure 5.1. Tungsten light bulb.

    Light Sources

    Incandescent/Tungsten Light

    Incandescent lighting is the easiest, most robust light technology. These lamps are cheap and emit a smooth spectrum of light, which is better than any other artificial sources. Bouncing a tungsten source off a gold reflector and onto a character’s face enhances their natural skin tones. Since the color from tungsten bulbs is kinder to skin tones, these bulbs are used in practicals.

    Focus!

    A practical is a light source that the audience can see in the frame, such as a bedside table lamp, candles, or office strip lights.
    From bottom to top, gradient from orange to blue: Kelvins run from 1,000 K on bottom to 10,000 K, with labels showing where different types of light fall in the scale, with candlelight being lowest and other artificial light as the scale increases to direct sun at just above 5,000 K and sky at the top.
    Figure 5.2. Kelvin scale.

    Incandescent lights pass an electrical current through a tungsten filament wire. This filament heats up and glows. Incandescent light is interchangeable with tungsten light, named after the filament metal. Dedolights and open-faced lights are used for this type of lighting.

    See Chapter 4, Lighting and Visual Composition, for more information about color temperature.

    The filament in a tungsten bulb has a temperature of 2,800-3,500K. Consequently, the color of the light emitted is red to orange and classified as indoor color temperature. In contrast, the surface of our sun is 5,778K, rendering the color of outdoor light blue.

    Tungsten-Halogen

    Clear glass tungsten halogen bulb showing the internal filament and metal pins at the base.
    Figure 5.3. Tungsten-halogen/quartz halogen bulb.

    This is a more advanced type of bulb than the incandescent one. Also called a quartz halogen, this type of bulb has a tungsten filament but is enclosed with a quartz envelope. This container is filled with halogen gas (iodine or bromine) and creates a chemical reaction, resulting in an efficient, bright light source. It allows for higher color temperatures and lasts longer due to the cycle of the gas. It is small, inexpensive, and can be used in car headlights, spotlights, household lamps, and projectors. The Dedolight is a branded example of this fixture used in the industry.

    LEDs

    While working for General Electric in 1962, American engineer Nick Holonyak Jr. invented a semiconductor laser diode that emitted visible light, pioneering the revolutionary Light-Emitting Diode (LED) lamp that we use today.[1] This lamp can match tungsten or daylight color temperatures. LEDs are rapidly replacing tungsten lamps on the market. Below is an example of an LED commonly used in film sets.

    Professors Isamu Akasaki, Hiroshi Amano, and Shuji Nakamura developed LEDs that emit blue light in the 1990s.[2] Their work paved the way for a generation of energy-efficient, color LED screens. “Gallium nitride was the key ingredient used by the Nobel laureates in their groundbreaking blue LEDs.”[3] LEDs are revolutionizing everything from landscape lighting to VR headsets. I visited the Las Vegas Sphere in March 2024, which had just opened six months earlier. Millions of LEDs lit up enormous screens inside the sphere and “transformed the exterior into almost any pattern or image you can imagine.”[4]

    Square LED panel light with a grid of small bulbs, mounted on a yoke and stand.
    Figure 5.4. Astra 6X Bi-Color LED Light Panel.

    Benefits of LEDs:

    • extremely energy efficient, saving on costs
    • last up to 100,000 hours (about eleven and a half years)
    • do not get hot
    • deliver high-quality light that does not degrade over time
    • can be battery operated
    • easy to dispose of; no toxic elements
    • can have remote-controlled dimmers
    A giant sphere lit up in the dark in Las Vegas.
    Figure 5.5. Spherical LED-covered building illuminated with swirling blue and turquoise light patterns at night.

    In 2015, Arri released their Sky Panel LED fixture. Varying in size, they are ultra-bright, high-quality LEDs that create soft light. These are best used as fill lights, as they struggle to create harsh shadows. The maximum power consumption for one of these is 400 W. Larger LED sky panels are very heavy and require two people to place onto a combo light stand.

    Focus!

    Combo Light Stands: A combo is a heavy-duty light without wheels. It is called a “combo” since it can be used for reflectors as well as lights.

    Rectangular soft LED panel with a flat diffusion surface, mounted on a support frame and stand.

    Rectangular LED panel light mounted on a yoke and stand, shown from the rear with ventilation grilles, connection ports, and an integrated control interface on the back.
    Figure 5.6. Front and rear views of the Arri SkyPanel LED light unit.

    A dimmer control panel adjusts the color temperature between 2,800K and 10,000K, but also can utilize the entire RGB spectrum. These units should never connect to a dimmer circuit as they will become permanently damaged. There is also an app (Stellar) that allows for remote control of the color temperature panel. It also has a plethora of presets for effects, such as police and flickering campfire light.

    Close-up of a lighting control panel with digital display and knobs, showing interface layout and adjustment controls.
    Figure 5.7. Arri SkyPanel color temperature control display.

    It can operate at ambient temperatures ranging from 2,800K-10,000K. This light can operate from a standard outlet or battery pack; however, if using household outlets, you must use the external power supply unit to adapt the AC power to DC power. The standard power supply input range is 100 to 240 volts, while the battery pack voltage is much lower at 23 to 26 volts.

    HMI and Ballast

    Hydrargyrum medium-arc iodide (HMI) lights create light with a color temperature of 5,600K, giving off a bright, white light that mimics sunlight. HMIs produce efficient, high-quality light, but are extremely expensive. They are particularly good when mixing indoor and outdoor light. They can be used for day-for-night shots to simulate exterior night by using them as bounce or fill. If you dial down your camera color balance settings to 3,200K, the HMI temperature will be blue and seem like moonlight. Below is an example of an HMI bulb.

    Large glass HMI bulb with visible internal arc tube and metal base pins, emphasizing the robust construction of a high-output lamp.
    Figure 5.8. Example of an HMI (hydrargyrum medium-arc iodide) bulb.

    Arri is the major manufacturer for HMIs, and Arrisun is their PAR daylight fixture. There are other brands such as Silver Bullet, Film Gear, and K5600. There are a variety of types of HMIs, including open-faced (as in the M18 below), PARs, and Fresnels; the entire category can only be dimmed down by 50% and are extremely expensive.

    Open-faced HMI light with a circular reflector and central bulb, mounted on a yoke; the reflective interior and round housing emphasize a focused, directional beam.
    Figure 5.9. Arri HMI M18 – 1800 watt – an open-faced HMI.

    An HMI is not operated by plugging into an electrical circuit. Instead, an electrical arc creates two electrodes producing a gas. To ignite and regulate the voltage and current, a ballast is needed. The ballast can be noisy, and older bulbs can flicker and have color variance. In addition, a special header cable connects the light to the ballast.

    Rectangular electronic ballast unit with vents, control panel, and cable connection; compact housing highlights functional design and power regulation components.
    Figure 5.10. Arri Ballast.

    There are two types of ballasts: magnetic and electronic. The least expensive ballast is the magnetic one, but it can create a flickering effect. Electronic ballasts have a flicker-free mode but, unfortunately, can produce a squealing or buzzing noise. Some electronic ballasts have a silent mode that can reduce this and can stop flickering but are poor for high-speed frame rates.

    Fluorescents

    Found almost everywhere, fluorescent lights are akin to HMIs in that they use gas for illumination. An electrical current makes mercury vapor emit ultraviolet light. A phosphor coating on the tube translates the UV light into the visible spectrum. The tubes, particularly older ones, flicker and cast an unhealthy, ugly green hue on characters’ skin tones. Kino Flo is the main brand manufacturer of fluorescent lighting in the industry. They require a ballast, just like HMIs. The light below uses four 55 W fluorescent lamps with an equivalency of 1,000 W.

    Fluorescent light fixture with multiple parallel tubes and hinged barn doors; linear lamp arrangement creates a broad, even rectangular light source.
    Figure 5.11. FloLight FL-220AWD Fluorescent Video Light with Wireless Dimming (5,400K Daylight).

    Close up

    Benefits of Fluorescents:

    • relatively inexpensive
    • very efficient, thus cost-effective
    • minimum heat produced but not overly hot
    • lamp life approximately 10,000 hours

    Other features of fluorescents to consider:

    • limited dimming capabilities
    • color temperature tubes available in 5,500K and 3,200K

    Types of Light Fixtures

    The following sections contain information regarding three main types of light fixtures: open-faced, PAR, and lensed light fixtures.

    Open-Faced Light

    This is the simplest form of electrical light, also known as an open reflector light, consisting of a filament inside a glass globe (bulb), housed in a metal casing, sitting in front of an aluminum reflector. It has a metal safety mesh at the front of the housing. There is no lens, no safety glass; it heats up very quickly, produces intense hard light, casts hard shadows (sometimes double shadows) on a subject, and is unable to focus or have any control over the spread of the beam of light.

    Focus!

    A light beam is a cone of light with a certain angular range that lights the area.
    Open-faced tungsten light with barn doors and a wire safety screen, featuring a cylindrical housing that directs a controllable beam.
    Figure 5.12. Redhead camera light.

    Adding accessories, such as a barn door, can help control the beam. The above image is a Redhead (rather misogynistic nickname), also known as a Mickey, with an 800 W bulb, and it has barn doors for attaching gels and diffusion. Its beam is thrown in an even, light pattern. A blonde (a tad misogynistic) has yellow housing and uses 2,000 W bulbs.

    Some open-faced lights have lenses, just like a closed-face lens (see PAR later in the chapter). However, since they are manufactured with the same configuration and an open-lensed fixture, they are still considered open-faced.

    Ceiling-mounted scoop light with a large curved reflector, designed to spread a broad, even wash of light downward.
    Figure 5.13. Scoop light.

    Scoop

    This is a simple, lightweight fixture also known as an Ellipsoidal Reflector Floodlight (ERF). It uses a tungsten halogen bulb housed inside a dome-like metal fixture and heats up very quickly. The metal acts as a basic reflector. Since it is open-faced there is no lens and it cannot be focused or controlled. It produces a wide, smooth wash and soft pool of light. Some scoops can throw light up to ten and twenty feet in diameter.

    Broad

    Not to be confused with the broad lighting technique, the Broad is a simple, no-nonsense, open-faced light. It consists of a box with a reflector and a double-ended bulb. It can come in assorted sizes, with the smallest version called a nook, mainly used as a fill or back light. Compact, efficient, and versatile, it has a rectangular beam pattern. The Broad usually has a 1-1.5k FCM or FHM bulb.

    Rectangular broad light with an open reflector and barn doors, producing a wide, unfocused beam for general illumination.
    Figure 5.14. Broad light fixture.
    Compact open-faced light with a rectangular reflector and protective glass, mounted on a yoke for directional control.
    Figure 5.15. Mole 1,000W Nook Light 2921.

    Here is an example of a nook manufactured by Mole-Richardson that uses a 1,000 W bulb. It is called a nook since it can fit into small, tight areas. It is affordable, and the rectangular beam makes it easy to blend. However, it is hard to use and can get extremely hot.

    Cyclorama Lights

    Wide theater stage with a symmetrical set and cyc backdrop, lit from above with colored stage lights that emphasize depth and background separation.
    Figure 5.16. Stage set illuminated with colored theatrical lighting.

    Originally used for theatrical backdrops in the 1920s, these are more commonly known as “cyc lights.” Compact and sturdy, they provide an even wash of light and color, eliminating shadows across a large area. Cyc lights are used in live performances, concerts, film, and television, and come in a variety of types using tungsten and LEDs. They are particularly useful for lighting green screens due to the quality of shadowless uniformity of light (see more on green screen in Chapter 15).

    Low-profile ground cyc light with a wide rectangular face angled upward to evenly illuminate a backdrop from below.
    Figure 5.17. Ground cyc.
    Rectangular cyc light with a wide diffuser panel emitting an even red glow, designed to wash large surfaces with uniform color.
    Figure 5.18. Spectra cyc 50 – 50 Watts 100-240VAC.

    Cycs can be placed anywhere, from low on the floor to up high on the grids and can have added color. Figures 5.17 & 5.18 are two examples.

    Lowel Tota-Lite

    Cinematographer Ross Lowell is credited with the invention of gaffer tape, found on every film set.

    Roll of black gaffer tape with a matte, textured surface and a partially peeled edge revealing the adhesive backing.
    Figure 5.19. Gaffer Tape.

    However, Lowell also developed a special open-faced light. In the 1950s, as a cinematographer he was often frustrated with available lighting fixtures when location shooting. He was looking for a robust but portable lighting system. Consequently, with experimentation, he created a small socket on a ball swivel that could accept a floodlight.

    In 1959, he started his Lowel-Light Company (now owned by Tiffen), developing a variety of open-faced fixtures. His Lowel Tota-light is also known as a “broad” because it casts light in an even, broad pattern. Compact, rugged, and versatile, this fixture can have an umbrella, gel, or diffusion attached to it for softer fill or backlight. With adjustable reflectors, it is good for bouncing light, background, and location work. It can be a smooth, even background light or can be pointed towards the ceiling to raise the ambient light.

    Compact open-face floodlight with a reflective interior and side wings, shaped to spread light broadly across a scene.
    Figure 5.20. Lowel T1-10 Tota Light, Tungsten.

    Omnilight

    Also created by Lowel, this basic open-faced light is small, light, robust, powerful, and portable. It contains attachment plates for installing tools such as an umbrella and a reflector. Gel can be secured on the barn doors with small clips. The one below has a 500W bulb with a wire mesh for safety. It can be handheld using the rubber hand grip but also can be secured on a stand. It has a wide focusing range, so it can be used as a key or backlight.

    Compact open-face floodlight with a reflective interior and side wings, shaped to spread light broadly across a scene.

    Rear view of a compact light showing ventilation slots, power input, and adjustment controls within a boxy housing.
    Figure 5.21. Omnilight, front and back views.

    Close up

    Omnilight tips:

    • It uses a tungsten bulb and generates heat, so you must be careful not to burn yourself. The rubber hand grip helps to avoid this type of accident.
    • Do not touch the bulb without gloves if you need to change it. Because it is tungsten, the oils from your hands can cause the bulb to shatter and even explode.
    Studio light with adjustable barn doors and a colored gel over the lens, demonstrating control of beam shape and light color.
    Figure 5.22. PAR light with barn doors, front view.

    Barn doors with small clips for holding diffusion materials, along with gel holders, can be purchased and attached to the Omnilight. This gives it more versatility in the field. See the example in figure 5.22.

    Parabolic Aluminized Reflector Lights

    Parabolic Aluminized Reflector (PAR) lights are frequently used in spotlights, concerts, theater and stage lighting, shopping mall displays, exterior landscaping, car headlamps, and airport runways. It produces a directional beam of light and can have dynamic color effects added.

    Runway at night with rows of red, green, and white lights
    Figure 5.23. Airport PAR runway lights.

    Classic PAR lights consist of a long, thin halogen filament inside a glass bulb protected by a metal housing called a PAR can. The reflector bowl and pressed lens inside the lamp refract light from the halogen lamp, providing directional lighting. The filament is long and thin, so it produces an oval beam rather than a circular one.

    Diagram of a parabolic lamp showing a central filament within a reflective housing, with arrows indicating directional light and heat paths.
    Figure 5.24. PAR lamp diagram

    PARs can provide wash lighting, in other words, broad, even illumination across an area such as a stage. They can light an entire wall, ceiling, or floor with a soft flood or focused beam of colored light and are popular for events. By adding gels for color effects, they can create mood, time, and even era. They are also effective for highlighting or emphasizing essential elements or areas of a scene. Additionally, they can be used as backlighting to add depth and separate actors from the background. This fixture can also have a mounting bracket for bolting to a light bar or truss.

    Row of stage lights fitted with colored gels, each circular lens glowing red, green, or yellow within rectangular barn door frames.
    Figure 5.25. Classic PAR lamps with colored gels.
    Close-up of a PAR light with a circular, faceted lens set inside a round housing, emphasizing the textured glass that shapes and spreads the beam.
    Figure 5.26. Exterior PAR light.

    The parabolic mirror concentrates light output into different beam spreads, otherwise known as beam angles.

    • clear lens: very narrow spot (VNSP).
    • lightly textured lens: narrow spot (NSP); useful for distant object illumination.
    • stippled lens: medium flood (MFL); spreads a broader beam than the VNSP.
    • more pronounced stippled lens: wide flood (WFL); produces a larger spread of beam.

    PARs come in a variety of shapes and sizes, from the minuscule PAR14 to the 1000W PAR64 cans. The PAR 64 VNSP 1200W moniker is “firestarter” due to the intense heat they produce.

    Row comparison of PAR bulbs in increasing sizes, showing variations in diameter and shape from small to large reflector lamps.
    Figure 5.27. PAR diameter sizes.

    The numbers are related to the size of their diameter, which is measured in 1/8th of an inch. A PAR64 is eight inches in diameter (64/8 = 8). PAR38 has a diameter of four and three-quarters inches (38/8 = 4.75). PAR16 has the nickname, Birdie.

    Maxibrutes (Molepars) are banks of multiple PAR64 (1KW) lights and come in banks of 4, 6, 9, 12, or 24

    PAR sizes
    Name Diameter
    PAR14 14/8 = 1.75 inches
    PAR16 16/8 = 2 inches
    PAR20 20/8 = 2.5 inches
    PAR30 long neck 30/8 = 3.75 inches
    PAR30 short neck 30/8 = 3.75 inches
    PAR36 36/8 = 4.5 inches
    PAR38 38/8 = 4.75 inches
    PAR46 46/8 = 5.75 inches
    PAR56 56/8 = 7 inches
    PAR64 64/8 = 8 inches

    PAR lamps are also available in a variety of wattages and beam spreads. For example, a PAR56 lamp can be 300 or 500 W. Bulbs are also available in the four main beam spreads: VNSP, NSP, MFL, and in the four main beam spreads: VNSP, NSP, MFL, and WFL.

    PARs are relatively inexpensive, simple, and versatile to use. In addition, the PAR38 is commonly sold at home improvement centers, so you can purchase one for last-minute emergencies. The PAR38’s wattage (75 W–300 W) allows for several to be plugged into the same electrical circuit without concern of overload. However, it should be positioned 10-20 feet from your subject.

    Line of stage-mounted PAR lights on a grid, each emitting a different color, forming a horizontal sequence of bright, colored beams.
    Figure 5.28. PAR lights on grid.

    Today, PAR lights have been given a new lease on life due to the introduction of LED light sources. Compared to the heat-searing halogen filament, multi-colored LED PARs have ultra-long-lasting life cycles due to their energy efficiency and almost zero heat produced and consequently can be used for extended periods of time. The 1K PAR has a comparable output to a 10K watt! They can produce all the colors of the rainbow with the touch of a switch. They also allow for plastic housing and DMX (Digital Multiplex) control. DMX is a system allowing multiple fixtures to be affected by a single controller. It uses a data signal to control the intensity, color, and other parameters of LED lights. Since the PAR light has been around for so long, the name has just remained.

    Lensed Lights: Fresnel’s Ship-Saving Invention

    Engraved portrait with dense crosshatching, emphasizing tonal shading and fine line texture across the face and clothing.
    Figure 5.29. Augustin Fresnel.

    In 1823, French physicist Augustin-Jean Fresnel (pronounced fray-nell) experimented with a scaled lens prototype at the Phare-de-Cordouan lighthouse near Bordeaux, France. This lens magnified the lighthouse flames and assisted sailors to see during severe weather or at night. His system revolutionized modern lighthouse lighting, and the “Fresnel lens” is used in most lighthouses worldwide.”[5] This “invention that saved a million ships.”[6] It had a lens consisting of concentric rings of glass prisms bending the light from inside to create a long, narrow beam of high intensity much greater than the light source itself.

    Large Fresnel lens assembly composed of concentric ridged glass segments arranged in a geometric frame; repeating circular patterns refract light into prismatic highlights.
    Figure 5.30. Fresnel Lens at Point Arena Lighthouse Museum.

    Fresnels have become the staples of television, movie, and photography studios. They come in a variety of manufacturers, light sources (tungsten, LED, and HMI), and sizes: from the small 100 W 2” LTM Pepper to the enormous 24,000 W I use Arri 150 W, 300 W, 650 W, and 1000 W Fresnels all the time in the studio. Fresnel lights come in different voltage rates, although the ones we use in class come with bulbs that have a voltage of 120V. They can be used as key, fill, back, rim, and eye lights depending on the wattage.

    Compact studio Fresnel light with a circular lensed front and protective housing, showing the stepped glass surface that focuses and controls a directional beam.
    Figure 5.31. Arri Fresnel 650-watt tungsten light.

    Close up

    Tungsten Fresnel’s come in the following wattages:

    • 100 watts
    • 150 watts
    • 200 watts
    • 300 watts
    • 650 watts
    • 1K (1,000 watts)
    • 2K (2,000 watts)
    • 4K (4,000 watts)
    • 5K (5,000 watts)
    • 10K (10,000 watts)
    • 12K (12,000 watts)
    • 20K (20,000 watts)
    • 24K (24,000 watts)

    Inside the Fresnel housing is a bulb positioned on a movable slider, called the sled. There is a round, black control knob at the back of the housing that allows the slider and bulb to move towards the lens. This spots the light, making it more intense and hard. Flooding the light by bringing the bulb back from the lens scatters the light, making it less intense and softer.

    Rear view of a compact Fresnel light showing a vented metal housing, power cable, and adjustment knob for controlling beam position.
    Figure 5.32. Back of Arri Fresnel 650.

    At the rear of the housing interior, behind the sled, is a spherical reflector that directs most of the light toward the lens, which then focuses the light into a beam. The housing unit is designed to reduce and cool the sled, bulb, and reflector as tungsten Fresnels generate massive amounts of heat. There are brackets at the front of the housing to attach barn doors and hence control light spill. Gels and diffusion can be fixed to the barn doors with C-47s. There is also a rigging space for inserting scrims and gobo holders for gobos.

    Main Components of a Fresnel Lens

    • Fresnel lens: the primary element, a thin, flat piece of glass with concentric circular grooves.
    • Lamp and reflector: the light source and its reflector, which directs light toward the lens.
    • Sled: the mechanism that holds the lamp and reflector and allows for adjustment.
    • Accessory bracket: this holds color filters and other accessories, such as scrims, in front of the lens.

    Adjustment mechanisms:

    • Tilt knob: adjusts the angle of the light beam.
    • Screw feed crank: moves the lamp and reflector along the sled, changing the focus.
    • Pan screw: adjusts the horizontal direction of the light.
    • C-clamp: used to attach the fixture to a stand or other support.
    • Yoke: a support structure that connects the lens to the clamp.

    Figure 5.33 is a diagram showing the main components and adjustment features of a Fresnel lens.

    Technical diagram of a Fresnel fixture with labeled components, including the lens, yoke, clamp, and internal lamp assembly, illustrating how the light is focused.
    Figure 5.33. Fresnel with main components diagram.

    Close up

    Fresnel nicknames

    • Inky: 100 watts
    • Midget: 200 watts
    • Tweenie: 650 watts
    • Baby: 1K watts
    • Junior: 2K watts
    • Senior: 4/5K watts

    Fresnel pros and cons

    • durable, robust workhorse
    • expensive, but it can last for many years.
    • heavy, but newer models are getting lighter all the time.
    • portable, especially if you buy a lighting kit in a rolling case.
    • versatile: can produce a hard-edged beam of light that is great for shadows but also produce soft light
    • uses a plethora of different light sources, sizes, and fixtures
    • produces extreme heat and requires gloves when handling
    • takes some time for lights to cool down, so unable to pack up immediately after a shoot
    • different accessories can be added (barn doors, scrims, gels, etc.).
    • produces harsh, crisp shadows when the beam is spotted; opposite when the beam is flooded
    • Fresnel LEDs produce a more yellow color than tungsten Fresnel lights.
    Compact on-camera light with a small circular lens and rounded housing, designed to project a focused beam directly forward.
    Figure 5.35. Eye light fixture example.

    Other forms of light

    Catch light

    A fabulous, mirror reflection of a light source seen in a character’s eye is a catch light. Also called a highlight, eye light, or Obie light, it is meant to show a glint in the eyes. This sparkle gives life to your characters, and without it, a character seems dead, shallow, or evil. It can be as simple as using an accessory shoe to attach a tiny, low-watt lamp at the top of the camera and lens. It can be a small Fresnel, fluorescent, or LED. The key is not to add light to the face but just catch the reflection in the eye.

    Eye lights have three basic settings: low, medium, and high, but each setting can be adjusted. To avoid overpowering other parts of the face, this light is intentionally dim and white in color.

    Centered studio portrait lit with soft, even frontal light; smooth tonal gradation and minimal shadows emphasize facial symmetry and detail.
    Figure 5.34. Merle Oberon the Obie.

    Close up

    The Obie is named after Merle Oberon, who was a British movie star in the Golden era of Hollywood. In 1937, she suffered facial scars due to a car crash. Seven years later, when filming The Lodger[7] Cinematographer (and later her husband), Lucian Ballard, created a small light to conceal her small scars. The light became known as the Obie light.[8]
    Close-up portrait framed by a circular ring light, creating even frontal illumination and a bright halo that centers the subject.
    Figure 5.36. Ring light.

    Other eye lights can be more pronounced and distinctive, such as the ring flash/ring light (ring-shaped reflections), soft boxes, or even beadboard (large square or rectangle highlights).

    China Balls

    Also called Chinese lanterns or Jem balls, these circular fixtures look like a Chinese paper lantern except they are made with silk. Consequently, they can cope with the rigors of filmmaking, which a paper lantern would not be able to do. French cinematographer Philippe Rousselot pioneered their use. He mounted them on booms that allowed for a soft-moving source to follow actors. In an interview for British Cinematographer, Philippe Rousselot said, “Chinese lanterns allow me to throw very soft light on faces, with practically no lights in the background, so I can isolate the actor from the background.”[9]

    round paper covered light with a handle that allows it to be hung
    Figure 5.37. China ball.

    China balls come in 22-inch and 30-inch sizes and produce an incredibly soft, 360-degree light. They are great for soft top lighting, party scenes, and even eye lights. A wire frame connects to hooks inside the lantern, which holds a variety of globes to suit your requirements. This system can be rigged and put in place very quickly. Cheap and versatile, the lanterns are excellent for soft lighting of a room or multiple subjects.

    Chapter Review

    I have covered the most popular lamps used in the film industry. However, there are hundreds of other brands of lights with a vast range of sources, wattage, power consumption, and styles. As technology advances, I am sure there will be more for you to explore as you advance in your career.

    Fresnel interactive exercise:

    Fill in the blanks exercise:

    Media Attributions


    1. Schubert, E. Fred. Light-Emitting Diodes. 3rd ed. Cambridge University Press. 2018, pp. 2–6. 1.05: Types of Lighting Instruments#return-footnote-37-1
    2. Webb, Jonathan. “Invention of Blue LEDs Wins Physics Nobel.” BBC News, 7 Oct. 2014, https://www.bbc.com/news/business-67076032. 1.05: Types of Lighting Instruments#return-footnote-37-2
    3. Webb, Jonathan. “Invention of Blue LEDs Wins Physics Nobel.” BBC News, 7 Oct. 2014, https://www.bbc.com/news/business-67076032. 1.05: Types of Lighting Instruments#return-footnote-37-3
    4. Baraniuk, Chris. “The Incredible Power of Blue LEDs.” BBC News, 16 Oct. 2023, https://www.bbc.com/news/business-67076032 1.05: Types of Lighting Instruments#return-footnote-37-4
    5. Phare-de-Cordouan. Official website of the Phare-de-Cordouan lighthouse. Accessed 26 Nov. 2024. https://www.phare-de-cordouan.fr/en/...rs-of-history/. 1.05: Types of Lighting Instruments#return-footnote-37-5
    6. Bernhard, Adrienne. “The Invention That Saved a Million Ships.” BBC Travel, 21 June 2019, https://www.bbc.com/travel/article/2...-million-ships. 1.05: Types of Lighting Instruments#return-footnote-37-6
    7. The Lodger. Directed by John Brahm, performances by Merle Oberon, Laird Cregar, and George Sanders, 20th Century Fox, 1944. 1.05: Types of Lighting Instruments#return-footnote-37-7
    8. Holben, Jay. “Eye Lights.” American Cinematographer, 1 Sept. 2018. Accessed 27 Nov. 2024. https://ascmag.com/blog/shot-craft/eye-lights. 1.05: Types of Lighting Instruments#return-footnote-37-8
    9. Pennington, Adrian. “Features: Philippe Rousselot ASC AFC.” British Cinematographer, https://britishcinematographer.co.uk...selot-asc-afc/. 1.05: Types of Lighting Instruments#return-footnote-37-9

    This page titled Chapter 5: Types of Lighting Instruments was last modified on Mon, 26 Oct 2026 17:17:02 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Roslin Smith via source content that was edited to the style and standards of the LibreTexts platform.