1.5: Compressible Flow Relationships

Aircraft Engine: Design and Analysis · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    1.5: Compressible Flow Relationships

    Six primary analytical relations govern compressible flow evaluations. These equations evaluate local state properties at a specific cross-section, rather than comparing states across two locations.

    1.6.1 Total or Stagnation Temperature

    The stagnation temperature Tt represents the fluid temperature attained when a stream at Mach number (Ma) is brought to rest adiabatically:

    \[Tt = T (1 +\dfrac{\left(k-1right)}{2}{ Ma}^2) \nonumber \]

    The bracketed term \(\dfrac{k-1}{2}Ma^2\) represents the ratio of dynamic kinetic energy to internal thermal energy in the moving stream.

    1.6.2 Total or Stagnation Pressure

    The stagnation pressure \(P\mathrm{t}\) is the pressure achieved if the flow is decelerated to rest isentropically:

    \[Pt = P {(1 +\dfrac{\left(k-1right)}{2}{ Ma}^2)}^{k/(k-1)} \nonumber \]

    This illustrates that flow decelerations raise pressure without mechanical compressors. Aircraft engines like ramjets and scramjets rely entirely on this freestream deceleration to achieve operating compression ratios.

    1.6.3 Total Pressure Mass Flow Parameter (MFP)

    Combining continuity with ideal gas laws, speed of sound, and stagnation relations yields the total pressure mass flow parameter: MFP = \(\dfrac{\dot{m}\sqrt{Tt}}{Pt A} \)

    \(\mathrm{MFP}\) help to calculate throat areas required for flow choking (\(Ma=1\)). Because \(\mathrm{MFP}\) depends exclusively on local Mach number and gas properties, it is widely tabulated. Note that a given \(\mathrm{MFP}\) value corresponds to two distinct Mach numbers (one subsonic and one supersonic), reaching its theoretical maximum at \(Ma=1 \) at which the flow is choked or sonic and the flow per unit area is the greatest.

    1.6.4Static Pressure Mass Flow Parameter

    Expressed using local static pressure, the static mass flow parameter is given by:

    \[{\mathrm{MF}}_p = \dfrac{\dot{m}\sqrt{Tt}}{P A} \nonumber \]

    This form is preferred in experimental setups where static pressure measurements are more accessible. Unlike \(\mathrm{MFP}\), each \({\mathrm{MF}}_p\) value maps uniquely to a single Mach number, allowing direct algebraic resolution

    1.6.5 Impulse Function (\(\boldsymbol{I}\) )

    The impulse function quantifies total axial momentum flux and pressure forces:

    \[I = PA + \dot{m} V = PA(1 + kMa^2) \nonumber \]

    Net force calculations across propulsion components simplify to the change in impulse function across the control volume \(\Delta I=I_{exit}-I_{entry}\), avoiding complex surface integrations over engine geometry.

    1.6.6 Dynamic Pressure

    Dynamic pressure scales fluid inertial forces relative to static pressures. The dynamic pressure \(q\) is given by the expression:

    \[P = \dfrac{1}{2}ρV^2 \nonumber \]

    It serves as the reference dynamic pressure across incompressible, compressible, and hypersonic regimes.

    1.6.7 Ratio of Specific Heats

    Engineers must select the specific heat ratio carefully so mathematical models align with real-world gas dynamics. In practice, two widely accepted estimates are k = 1.33 for temperatures from 2500 to 3000\(\mathrm{{}^\circ}\) R, and k = 1.30 for 3000 to 3500\(\mathrm{{}^\circ}\) R.


    This page titled 1.5: Compressible Flow Relationships was last modified on Wed, 18 Nov 2026 07:18:38 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by .