2.3: Problems and References

Aircraft Engine: Design and Analysis · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    2.3: Problems and References

    Problem#1

    Air flows through a circular duct of uniform cross-sectional area with an inner diameter of \(D=0.5~\mathrm{ft}\). At the duct inlet, the flow parameters are recorded as Mach number \({Ma}_1=0.35\), static pressure \(p_1=15~\mathrm{psia}\), and static temperature \(T_1=520~\mathrm{{}^\circ R}\). Thermal energy is added to the air stream at a rate of \(\dot{Q}=200~\mathrm{BTU/s}\). Assuming frictionless, one-dimensional Rayleigh flow with \(k=1.4\), \(c_p=0.24~\mathrm{BTU/(lbm}\cdot \mathrm{{}^\circ R)}\), and gas constant \(R=1716~\mathrm{ft}\cdot \mathrm{lbf/(slug}\cdot \mathrm{{}^\circ R)}\) (or \(53.34~\mathrm{ft}\cdot \mathrm{lbf/(lbm}\cdot \mathrm{{}^\circ R)}\)), determine:

    1. Mass flow rate through the channel, \(\dot{m}\) (\(\mathrm{lbm/s}\))
    2. The threshold thermal addition rate, \({\dot{Q}}^*\), required to choke the exit (\({Ma}_2=1\)) for these inlet conditions
    3. Exit Mach number, \({Ma}_2\)
    4. Percentage reduction in total pressure, \(Δp_t/p_{t1}\times 100\%\)
    5. Change in specific entropy, \(Δs\) (\(\mathrm{BTU/(lbm}\cdot \mathrm{{}^\circ R)}\))
    6. Total static pressure change, \(Δp=p_1-p_2\) (\(\mathrm{psi}\))
    7. Sketch and label the inlet (State 1) and exit (State 2) conditions along a Rayleigh line on a Temperature–entropy (\(T--s\)) diagram.

    Problem#2

    Find the maximum specific heat input, \(q^*\), that can be added to a uniform, frictionless duct flow before reaching thermal choking at the exit. The air enters the channel at a supersonic Mach number of \({Ma}_1=2.4\) with an inlet static temperature of \(T_1=-{20}^{\circ }\mathrm{C}\) (\(253.15~\mathrm{K}\)).

    Assume the working fluid is air with:

    • Specific heat ratio, \(k=1.4\)
    • Specific heat at constant pressure, \(c_p=1005~\mathrm{J/(kg}\cdot \mathrm{K)}\)

    Project#1

    Rayleigh Flow & Thermal Choking Limits in Scramjet Combustors

    Objective: Model the 1D Rayleigh flow through a constant-area combustion chamber with variable heat release profiles.

    Core Tasks:

    1. Critical Heat Input (\({\boldsymbol{q}}^{\boldsymbol{*}}\))

    • The total temperature as a function of Mach number \[\frac{T_t}{T_t^*}=\frac{2(k+1) M a^2\left(1+\frac{k-1}{2} M a^2\right)}{\left(1+k M a^2\right)^2} \nonumber\] where \[\dot{m}\left(h_{t2}-h_{t1}\right)=\dot{Q}\Longrightarrow h_{t2}-h_{t1}=q. \nonumber \]

      Assuming constant specific heat (\(h=c_pT\)), this becomes: \[q=c_p\left(T_{t2}-T_{t1}\right) \nonumber \] Then \(q^*=c_p\left(T^*_t-T_{t1}\right)\) Therefore, the critical heat input: \[q^*=c_pT_{t1}\left[\frac{{\left(1+k{Ma}^2_1\right)}^2}{2\left(k+1\right){Ma}^2_1\left(1+\frac{k-1}{2}{Ma}^2_1\right)}-1\right] \nonumber \]

    2. Maximum Fuel-to-Air Ratio (\(Φ_{\mathrm{crit}}\))

    • Assuming complete combustion of a standard hydrocarbon fuel (e.g., Jet-A or Kerosene with lower heating value \(LHV\approx 43~\mathrm{MJ/kg}\) and stoichiometric ratio \(f_{\mathrm{stoich}}\approx 0.068\)): \[q^*=\frac{f\cdot LHV}{1+f}\approx f_{\mathrm{crit}}\cdot LHV\Longrightarrow f_{\mathrm{crit}}=\frac{q^*}{LHV-q^*} \nonumber \] The equivalence ratio \(Φ_{\mathrm{crit}}\) is: \[Φ_{\mathrm{crit}}=\frac{f_{\mathrm{crit}}}{f_{\mathrm{stoich}}} \nonumber \]
    • Benchmark Calculations Across Varying Inlet Mach Numbers (\({\boldsymbol{Ma}}_{\boldsymbol{1}}\))
    • Assumed flow parameters: \(T_1=300~\mathrm{K}\), \(γ=1.4\), \(c_p=1005~\mathrm{J/(kg}\cdot \mathrm{K)}\), \(LHV=43~\mathrm{MJ/kg}\), \(f_{\mathrm{stoich}}=0.068\).

    Using EES (parametric tables) to determine the maximum allowable fuel-to-air ratio (\(Φ_{\mathrm{crit}}\)) and critical heat input (\(q^*\)) before thermal choking (\(Ma=1\)) occurs at the exit for varying inlet Mach numbers (\({Ma}_1= \text{from 2.0 to 3 and the increment is 0.2}\).

    References

    Anderson, J. D. (2003). Modern Compressible Flow: With Historical Perspective (3rd ed.). McGraw-Hill Education.

    Shapiro, A. H. (1953). The Dynamics and Thermodynamics of Compressible Fluid Flow (Vol. 1). Ronald Press.

    Mattingly, J. D. (1996). Elements of Gas Turbine Propulsion. McGraw-Hill.

    Oates, G. C. (1988). Aerothermodynamics of Gas Turbine and Rocket Propulsion. AIAA Education Series


    This page titled 2.3: Problems and References was last modified on Wed, 18 Nov 2026 07:18:34 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Haifa El-Sadi.