4.6: Problems and References

Aircraft Engine: Design and Analysis · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    4.6: Problems and References

    Problem#1

    A multistage axial-flow compressor processes a mass flow rate of \(60~\mathrm{kg/s}\) with an overall total pressure ratio of \(40\). The compressor operates with a polytropic efficiency of \(e_c=0.88\). At the compressor inlet, the total temperature and total pressure are \(T_{t2}=295~\mathrm{K}\) and \(p_{t2}=101.3~\mathrm{kPa}\), respectively. Assuming steady, adiabatic flow and constant fluid properties throughout the compression process (\(k=1.40\) and \(c_p=1004.5~\mathrm{J/(kg}\cdot \mathrm{K)}\)), determine:

    1. The compressor exits total temperature, \(T_{t3}\) (\(\mathrm{K}\))
    2. The overall compressor adiabatic (isentropic) efficiency, \(η_c\)
    3. The required compressor shaft power, \({\mathcal{P}}_c\) (\(\mathrm{MW}\))

    Problem#2

    A gas turbine combustor operates with an inlet total temperature of \(T_{t3}=1150~^{\circ }\mathrm{R}\) and an inlet total pressure of \(p_{t3}=450~\mathrm{psia}\). The incoming air mass flow rate is \({\dot{m}}_a=220~\mathrm{lbm/s}\), with inlet fluid properties of \(k_3=1.40\) and \(c_{p3}=0.240~\mathrm{Btu/(lbm}{\cdot }^{\circ }\mathrm{R)}\). A hydrocarbon fuel with a lower heating value of \(Q_R=18,500~\mathrm{Btu/lbm}\) is injected into the burner at a rate of \({\dot{m}}_f=4.4~\mathrm{lbm/s}\). The combustor operates with a burner efficiency of \(η_b=0.98\), and fluid friction/heat addition results in a \(4\%\) total pressure loss across the burner (\(p_{t4}=0.96 p_{t3}\)). The working fluid properties at the combustor exit are \(k_4=1.33\) and \(c_{p4}=0.276~\mathrm{Btu/(lbm}{\cdot }^{\circ }\mathrm{R)}\).

    Calculate:

    1. The fuel-to-air ratio, \(f\)
    2. The combustor exit total pressure, \(p_{t4}\) (\(\mathrm{psia}\))
    3. The combustor exit total temperature, \(T_{t4}\) (\(\mathrm{R}\))

    Problem#3

    An uncooled turbine receives working fluid at its inlet with conditions matching the combustor exit: \(T_{t4}=1450~\mathrm{K}\), \(p_{t4}=3.0~\mathrm{MPa}\), and total mass flow rate \(\dot{m}=105~\mathrm{kg/s}\). The turbine operates with an adiabatic efficiency of \(η_t=0.88\). The total power extracted by the turbine to drive the compressor and engine accessories is \({\mathcal{P}}_t=65~\mathrm{MW}\).

    Assuming the fluid properties remain constant across the turbine stage at \(k=1.33\) and \(c_p=1150~\mathrm{J/(kg}\cdot \mathrm{K)}\), calculate:

    1. The turbine exit total temperature, \(T_{t5}\) (\(\mathrm{K}\))
    2. The turbine stage polytropic efficiency, \(e_t\)
    3. The turbine exit total pressure, \(p_{t5}\) (\(\mathrm{kPa}\))
    4. The required total temperature drop across the turbine, \(ΔT_t=T_{t4}-T_{t5}\) (\(\mathrm{K}\))

    Problem#4

    Consider a supersonic convergent–divergent (CD) exhaust nozzle operating at a nozzle pressure ratio of \(\mathrm{NPR}=12\). The working fluid maintains constant gas properties throughout the expansion, given by \(k=1.30\) and \(c_p=1240~\mathrm{J/(kg}\cdot \mathrm{K)}\). The nozzle’s adiabatic expansion efficiency is \(η_n=0.96\).

    Determine:

    1. The nozzle total pressure recovery ratio (\(π_n\)).
    2. The area ratio of the exit to the throat (\(A_9/A_8\)) for a perfectly expanded condition.
    3. The nozzle exit Mach number (\({Ma}_9\)) under perfectly expanded operation

    Problem#5

    A ramjet flies at a flight Mach number of \({Ma}_0=3.2\) in an altitude ambient environment where \(T_0={390}^{\circ }\mathrm{R}\) (\(p_0=1.6~\mathrm{psia}\)). The inlet diffuser has a total pressure recovery of \(π_d=0.88\). The combustor burns hydrogen fuel with a lower heating value of \(Q_R=50,500~\mathrm{Btu/lbm}\) at a burner efficiency of \(η_b=0.96\), raising the total temperature at the burner exit to \(T_{t4}={3800}^{\circ }\mathrm{R}\). The nozzle expands the gas perfectly back to ambient pressure (\(p_9=p_0\)) but experiences a total pressure loss fraction of \(π_n=0.94\).

    Assume standard gas properties throughout the engine:

    • Air/Unburned Fluid (Inlet & Diffuser): \(k_0=1.40\), \(c_{pc}=0.240~\mathrm{Btu/(lbm}{\cdot }^{\circ }\mathrm{R)}\)
    • Burner & Exhaust Fluid: \(k_g=1.33\), \(c_{pg}=0.276~\mathrm{Btu/(lbm}{\cdot }^{\circ }\mathrm{R)}\)

    Calculate:

    1. Fuel-to-air ratio, \(f\)
    2. Nozzle exit Mach number, \({Ma}_9\)
    3. Specific net thrust, \(F_n/{\dot{m}}_0\) (\(\mathrm{lbf}/\left(\mathrm{lbm/s}\right)\))
    4. Thermal efficiency, \(η_{th}\)
    5. Propulsive efficiency, \(η_p\)

    image11.png

    Problem#6

    A non-afterburning mixed-flow turbofan engine operates under the following design and limit parameters at high-altitude supersonic flight:

    • Flight Conditions: Flight Mach number \({Ma}_0=2.0\), ambient static pressure \(p_0=12~\mathrm{kPa}\), ambient static temperature \(T_0=220~\mathrm{K}\) (\(-{53.15}^{\circ }\mathrm{C}\)). Gas constant \(R=287~\mathrm{J/(kg}\cdot \mathrm{K)}\) and specific heat ratio \(k=1.40\) (\(c_p=1004.5~\mathrm{J/(kg}\cdot \mathrm{K)}\)) throughout the engine.
    • Inlet & Mass Flow: Total engine mass flow rate \({\dot{m}}_0=\left(1+α\right){\dot{m}}_{\mathrm{core}}=30~\mathrm{kg/s}\), inlet total pressure recovery \(π_d=0.88\).
    • Fan & Compressor: Fan pressure ratio \(π_f=1.6\), fan polytropic efficiency \(e_f=0.89\). Overall compressor pressure ratio \(π_c=18\), compressor polytropic efficiency \(e_c=0.89\).
    • Combustor: Combustor total pressure ratio \(π_b=0.94\), burner efficiency \(η_b=0.98\), fuel lower heating value \(Q_R=43,000~\mathrm{kJ/kg}\), turbine inlet total temperature \(T_{t4}=1723.15~\mathrm{K}\) (\({1450}^{\circ }\mathrm{C}\)).
    • Turbine & Mechanical Transmission: Turbine polytropic efficiency \(e_t=0.90\), mechanical transmission efficiency \(η_m=0.97\), Mach number at turbine exit Station 5 \({Ma}_5=0.45\).
    • Mixer & Duct: Fan duct (Stations 13 to 15) is frictionless and adiabatic (\(p_{t15}=p_{t13},T_{t15}=T_{t13}\)). Total pressure ratio across fan side of mixer \(π_{M,f}=0.97\). Equal static pressure constraint applies at mixer entry (\(p_{15}=p_6\)).
    • Exhaust Nozzle: Nozzle total pressure ratio \(π_n=0.92\), nozzle exit static pressure matches ambient (\(p_9=p_0\)).

    Calculate:

    1. Ram drag, \(D_R\) (\(\mathrm{kN}\))
    2. Inlet exit/Fan inlet stagnation properties: \(p_{t2}\) (\(\mathrm{kPa}\)) and \(T_{t2}\) (\(\mathrm{K}\))
    3. Compressor exit stagnation properties: \(p_{t3}\) (\(\mathrm{kPa}\)) and \(T_{t3}\) (\(\mathrm{K}\))
    4. Fan duct exit stagnation properties: \(p_{t13}\) (\(\mathrm{kPa}\)) and \(T_{t13}\) (\(\mathrm{K}\))
    5. Burner exit total pressure \(p_{t4}\) (\(\mathrm{kPa}\)) and turbine exit total temperature \(T_{t5}\) (\(\mathrm{K}\))
    6. Fuel-to-air ratio, \(f\)
    7. Bypass ratio \(α\), core mass flow rate \({\dot{m}}_{\mathrm{core}}\) (\(\mathrm{kg/s}\)), and fan duct mass flow rate \({\dot{m}}_{\mathrm{fan}}\) (\(\mathrm{kg/s}\))
    8. Mixed total temperature \(T_{t6M}\) (\(\mathrm{K}\))
    9. Nozzle inlet stagnation properties: \(p_{t9}\) (\(\mathrm{kPa}\)) and \(T_{t9}\) (\(\mathrm{K}\))
    10. Nozzle exit Mach number \(M_9\) and exit velocity \(V_9\) (\(\mathrm{m/s}\))
    11. Gross thrust \(F_g\) (\(\mathrm{kN}\)) and net thrust \(F_n\) (\(\mathrm{kN}\))
    12. Thrust-specific fuel consumption (\(\mathrm{TSFC}\)) (\(\mathrm{mg/s/N}\))

    image12.png

    Problem#7

    A single-spool turbojet engine operates under the following on-design (sea-level static) conditions:

    • Flight Conditions: \({Ma}_0=0\), \(p_0=101.325~\mathrm{kPa}\), \(T_0=288.15~\mathrm{K}\), \(k=1.40\), and \(c_p=1.0045~\mathrm{kJ/(kg}\cdot \mathrm{K)}\).
    • Inlet: Total pressure recovery ratio \(π_d=0.98\).
    • Compressor: Overall total pressure ratio \(π_c=25\), polytropic efficiency \(e_c=0.88\).
    • Combustor: Burner efficiency \(η_b=0.98\), burner total pressure ratio \(π_b=0.94\), fuel lower heating value \(Q_R=43,000~\mathrm{kJ/kg}\), and burner temperature ratio limit parameter \(τ_λ=\dfrac{T_{t4}}{T_0}=6.2\).
    • Turbine: Polytropic efficiency \(e_t=0.89\), mechanical transmission efficiency \(η_m=0.96\).
    • Nozzle: Total pressure ratio \(π_n=0.97\), perfectly expanded (\(p_9/p_0=1.0\)).

    Calculate for the on-design condition:

    1. Compressors exit total pressure \(p_{t3}\) (\(\mathrm{kPa}\)) and compressor temperature ratio \(τ_c=T_{t3}/T_{t2}\).
    2. Fuel-to-air ratio \(f\) and combustor exit total pressure \(p_{t4}\) (\(\mathrm{kPa}\)).
    3. Turbine temperature ratio \(τ_t=T_{t5}/T_{t4}\).

      For the off-design condition (\(M_0=0.80\) at an altitude of \(11~\mathrm{km}\), where \(T_{0,\mathrm{off}}= 216.65~\mathrm{K}\), \(p_{0,\mathrm{off}}=22.63~\mathrm{kPa}\)), the engine throttle is adjusted such that \(T_{t4,\mathrm{off}}= 0.92 T_{t4,\mathrm{design}}\). Assuming constant turbine temperature ratio (\(τ_{t,\mathrm{off}}=τ_{t,\mathrm{design}}\)) and choked turbine nozzle conditions:

    4. Calculate the off-design compressor total pressure ratio, \(π_{c,\mathrm{off}}\).

    Problem#8

    An advanced turboprop engine flies at a cruise Mach number of \({Ma}_0=0.70\) at a standard flight altitude of \(35,000~\mathrm{ft}\) (\(T_0=394.1~^{\circ }\mathrm{R}\), \(p_0=3.468~\mathrm{psia}\), \(a_0=973.1~\mathrm{ft/s}\)). The core mass flow rate is \({\dot{m}}_{\mathrm{core}}=45~\mathrm{lbm/s}\).

    The design and operating component parameters are as follows:

    • Diffuser: Total pressure recovery ratio \(π_d=0.98\)
    • Compressor: Overall pressure ratio \(π_c=20\), polytropic efficiency \(e_c=0.90\)
    • Combustor: Total pressure ratio \(π_b=0.95\), burner efficiency \(η_b=0.98\), fuel heating value \(Q_R=18,500~\mathrm{Btu/lbm}\), turbine inlet total temperature \(T_{t4}=3000~^{\circ }\mathrm{R}\)
    • Compressor Turbine: Drives the compressor with mechanical efficiency \(η_{m1}=0.99\) and polytropic efficiency \(e_{t1}=0.90\)
    • Power Turbine: Drives the propeller through a reduction gearbox (\(η_{gb}=0.98\)) with mechanical efficiency \(η_{m2}=0.98\) and polytropic efficiency \(e_{t2}=0.90\)
    • Propeller: Propeller efficiency \(η_{\mathrm{prop}}=0.83\)
    • Exhaust Nozzle: Total pressure ratio \(π_n=0.96\), expanding to ambient pressure
    • Fluid Properties: \(k=1.40\), \(c_p=0.240~\mathrm{Btu/(lbm}{\cdot }^{\circ }\mathrm{R)}\) throughout the engine.

    Assuming an optimum power split fraction (\(α_{\mathrm{opt}}\)) that maximizes total net thrust, calculate:

    1. Core net thrust, \(F_{n,\mathrm{core}}\) (\(\mathrm{lbf}\))
    2. Propeller net thrust, \(F_{n,\mathrm{prop}}\) (\(\mathrm{lbf}\))
    3. Overall thrust-specific fuel consumption, \(\mathrm{TSFC}\) (\(\mathrm{lbm/(h}\cdot \mathrm{lbf)}\))
    4. Overall engine thermal efficiency (\(η_{th}\)) and overall efficiency (\(η_o\))

    image13.png

    Problem#9

    A military supersonic jet powered by a augmented (afterburning) turbojet engine operates at a cruise Mach number of \({Ma}_0=2.2\) at an altitude where the static pressure is \(p_0=12~\mathrm{kPa}\) and ambient static temperature is \(T_0=-{50}^{\circ }\mathrm{C}\) (\(223.15~\mathrm{K}\)).

    The cold-section gas properties are \(k_c=1.4\) and \(c_{pc}=1005~\mathrm{J/(kg}\cdot \mathrm{K)}\). The engine component performance characteristics are:

    • Inlet Diffuser: Total pressure recovery ratio \(π_d=0.90\)
    • Compressor: Overall pressure ratio \(π_c=15\), polytropic efficiency \(e_c=0.89\)
    • Main Combustor: Non-dimensional enthalpy limit \(τ_λ=8.5\), fuel heating value \(Q_R=43,000~\mathrm{kJ/kg}\), burner efficiency \(η_b=0.98\), pressure ratio \(π_b=0.96\)
    • Turbine: Hot-gas properties \(k_t=1.33\) and \(c_{pt}=1150~\mathrm{J/(kg}\cdot \mathrm{K)}\), polytropic efficiency \(e_t=0.84\), mechanical transmission efficiency \(η_m=0.99\)
    • Afterburner: Non-dimensional enthalpy limit \(τ_{λ\mathrm{AB}}=11.5\), fuel heating value \(Q_{R\mathrm{AB}}=43,000~\mathrm{kJ/kg}\), combustion efficiency \(η_{\mathrm{AB}}=0.97\), pressure ratio \(π_{\mathrm{AB}}=0.94\), gas properties \(k_{\mathrm{AB}}=1.30\) and \(c_{p\mathrm{AB}}=1240~\mathrm{J/(kg}\cdot \mathrm{K)}\)
    • Exhaust Nozzle: Pressure ratio \(π_n=0.95\), expanding to ambient pressure (\(p_9=p_0\))

    Determine:

    1. Stagnation pressures (\(p_t\)) and temperatures (\(T_t\)) at all major engine stations, along with main burner (\(f\)) and afterburner (\(f_{\mathrm{AB}}\)) fuel-to-air ratios.
    2. Non-dimensional specific thrust \(\dfrac{F_n}{{\dot{m}}_0a_0}\).
    3. Thrust Specific Fuel Consumption (\(\mathrm{TSFC}\)) expressed in \(\mathrm{mg/(s}\cdot \mathrm{N)}\).
    4. Overall thermal efficiency (\(η_{\mathrm{th}}\)) and propulsive efficiency (\(η_p\)).

    References

    Mattingly, J. D. (1996). Elements of Gas Turbine Propulsion. McGraw-Hill Education.

    (2nd Edition: Mattingly, J. D., & Boyer, K. M. (2014). American Institute of Aeronautics and Astronautics).

    Mattingly, J. D., Heiser, W. H., & Pratt, D. T. (2002). Aircraft Engine Design (2nd ed.). American Institute of Aeronautics and Astronautics (AIAA).

    Farokhi, S. (2014). Aircraft Propulsion (2nd ed.). John Wiley & Sons.

    Kerrebrock, J. L. (1992). Aircraft Engines and Gas Turbines (2nd ed.). The MIT Press


    This page titled 4.6: Problems and References was last modified on Wed, 18 Nov 2026 07:22:37 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Haifa El-Sadi.