5.5.3: Lighting Sources

Applied Botany · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY-NC-SA 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    5.5.3: Lighting Sources

    Today there are multiple light sources available to meet the needs of different applications. They vary in initial cost, light intensity, spectrum produced and cost of operation.

    Incandescent lamps produce light as electricity moves through a wire filament. Much of the energy consumed is lost as heat rather than usable light. These lamps produce approximately 17 lumens per watt. The light spectrum produced (Figure 5-30) is predominately red with very little emitted in the violet and blue regions. The primary benefit is that both the fixtures and the lamps themselves are cheap. However, the cost of operating is significant and only produces low intensity light. With most of the emitted light in the orange-red region of the spectrum they are suited for use in photoperiodic lighting.

    Output spectrum of an incandescent lamp very low or no intensity in the blue.
    Figure 5-30. Output spectrum of an incandescent lamp, with intensity on the y-axis and wavelength on the x-axis. There is very low or no intensity in the blue, and intensity rises steadily to its highest in the red. (https://www.researchgate.net/figure/...fig1_312320039)

    Fluorescent tubes produce light as electricity excites mercury vapor. The short-wave ultraviolet light it produces causes a phosphor coating on the inside of the lamp to glow. Most of the energy consumed is converted to usable light and thus these lamps are significantly more efficient than incandescent lamps. They produce approximately 50 lumen per watt. The light intensity produced is low to moderate but with more blue light and very little red (Figure 5-31). The low/moderate light intensity typically means the light sources need to be relatively close to the plants. Since they produce so little heat, placing the lights close to vegetation is not detrimental. Fluorescent fixtures and bulbs are relatively cheap and do not require any specialized knowledge for installation. However, their low/moderate intensity means that they work for supplemental lighting, but only in crops that have moderate light demands. They are useless for photoperiodic lighting due to the lack of red in their spectra.

    Output spectrum of a fluorescent tube-Low intensity with spikes in blue and green but none in red.
    Figure 5-31. Output spectrum of a fluorescent tube. Graph with intensity along y-axis and wavelengths along x-axis. Low intensity with spikes in blue and green but none in red. (https://www.researchgate.net/figure/...fig1_312320039)

    Compact fluorescent lamps produce the same spectrum of light as the tube fluorescent types. One benefit is that they can be used in fixtures designed for incandescent lamps since the lamps have integrated electric ballasts. Tubes require special fixtures that include ballast. For plant growth, tubes are typically preferred as they provide more coverage area than the compact style.

    It is important to note that the presence of the mercury vapor in fluorescent tubes and lamps means they are classified as hazardous waste. They should be disposed of or recycled appropriately.

    Commonly used in street lighting, high-pressure sodium (HPS) lamps produce light by passing energy through vaporized sodium under high pressure. HPS lamps are more efficient than fluorescent or incandescent lamps. They produce approximately 80-120 lumens/watt. The spectrum they produce is dominated by orange and red (Figure 5-32). While significantly more efficient than incandescent lamps they still emit a lot of heat which may impact plants or require other environmental controls. The fixtures and lamps are pricey and may take some specialized knowledge for installation. The fixtures for these lamps must include a rather bulky ballast. This may require strengthening of structural supports due to the ballast unit’s weight. Additionally, the bulk of the instrument blocks natural lighting. To avoid these issues, some manufacturers have ballasts independent of the light fixture. These ballasts can be placed some distance away and can power multiple fixtures. In the greenhouse, HPS lamps are used for supplemental lighting and can be used for sole-source lighting as well.

    Spectrum of a high-pressure sodium lamp- Intensity is low in the blue and highest in orange and red.
    Figure 5-32. Output spectrum of a high-pressure sodium lamp, with intensity on the y-axis and wavelength on the x-axis. Intensity is low in the blue and rises through the green and yellow to its highest in the orange and red. (Scientific Figure on ResearchGate. Available from: https://www.researchgate.net/figure/...fig1_312320039 [accessed 13 Sep 2019])

    Metal halide (MH) lamps are often preferred for some applications because they provide a more “natural sunlight” illumination as compared to the orange cast of the HPS lamps. The MH lamps produce light by passing energy through a mixture of vaporized mercury and compounds of metals with bromine or iodine (some versions use other halides) (Figure 5-33). They produce a high intensity light that emits well across the spectrum, as can be seen in the graph on this slide. Their energy efficiency is slightly higher than that of the HPS at 90-130 lumens/watt. The cost of the fixtures and lamps is about the same as the HPS. The MH lamps have some of the same drawbacks as the HPS. They require ballast and thus specialized fixtures. Modern ballasts are smaller, which does help with the weight and shading issues. The bulbs, however, have shorter life expectancy and thus any financial savings from energy efficiency is usually negated. These lamps are typical of sole-source lighting and can be used for supplemental as well.

    Spectrum metal halide lamp -High intensity across most of spectrum but slightly lower in the blues.
    Figure 5-33. Light spectrum emitted by Metal halide lamps. (Scientific Figure on ResearchGate. Available from: https://www.researchgate.net/figure/...fig1_312320039 [accessed 13 Sep 2019])

    The newest trend in plant lighting is the use of LED (Light emitting diodes). Each LED light produces a very narrow band of light (Figure 5-34). LED “grow lights” are made by creating large banks of LEDs emitting different wavelength. This can allow for the “tuning” of the light spectrum produced to complement the crops. For example, LED grow lights concentrate on producing red and blue light. Use of only red and blue lights provides the most cost-efficient method of growth; however, some studies have detected benefits associated with the addition of green light.

    Spectrum of a blue LED lamp -  single peak at 460 nm. No other color is produced.
    Figure 5-34.  Output spectrum of a blue LED lamp. Graph with intensity along y-axis and wavelengths along x-axis. Produces a single peak at 460 nm. No other color is produced. (Scientific Figure on ResearchGate. Available from: https://www.researchgate.net/figure/...fig1_312320039 [accessed 13 Sep 2019])

    LED equipment is more expense to purchase; however, the energy efficiency typically pays for the price difference within two years. Their energy efficiency varies with the array of colors emitted but it is typically 60-80% more efficient than HPS or MH lamps (100-300 lumens/watt are reported). They can be used for supplemental, photoperiodic, or sole-source lighting. Their low heat production makes the ideal from many applications.


    This page titled 5.5.3: Lighting Sources was last modified on Fri, 13 Nov 2026 17:33:37 GMT and is shared under a CC BY-NC-SA 4.0 license and was authored, remixed, and/or curated by Stephanie Harvey.