9.2.1: Cuttings from Woody Plants

Applied Botany · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY-NC-SA 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    9.2.1: Cuttings from Woody Plants

    Many plants produce vegetative propagules to maximize their reproductive potential. In the absence of a sexual partner they can still produce “offspring”. We can harvest these propagules and use them to create plants for human usage. We can also use the innate cloning ability to force the creations of propagules. Techniques allow the creation of propagules from vegetative organs including leaves, stem and storage organs.

    Cuttings: Cutting is a propagation method that takes advantage of plants’ ability to generate adventitious roots and other tissues. In cutting, a portion of a plant is removed from a “parent” plant and then triggered to produce new root and shoot material. Cutting techniques are typically divided into two groups – cuttings from herbaceous plants and cuttings from woody plants. In the segment we will discuss several techniques for each type of plant. With all cuttings it is critical to maintain the “shoot-root” orientation. If the tip end is planted down, the x-plant is likely to rot instead or root. Remember – the difference between ROT and ROOT is the O – orientation.

    Woody plants are defined as those that produced 2nd growth in the form of 2nd xylem. They are typically perennials that live many years and thus survive winters. Example of woody plants would include trees and shrubs. The type of cutting used with woody plants is based on when the cutting is taken and the physiological state of the cutting at the time of removal from the parent. The three types are named after the state of the woody cutting: softwood cuttings, semi-hardwood cuttings and hardwood cuttings.

    Softwood cuttings are cuttings taken in spring after a new flush of growth. The cutting should be about 4 to 6 inches long, from the new growth. The cuttings lacks roots and can quickly desiccate especially since they will have leaves. Since the leaves are the primary site of water loss, some trimming down of their size can be helpful (Figure 9-22). You don’t want to remove all the leaves since energy from photosynthesis is need for the new growth. However, removing 40-50% of a large leaf will reduce water loss. Cuttings should ideally be placed in a mist bed. If a mist bed is not available, you can create a tent to trap moisture but be careful not to let too much heat get trapped or else the cutting can be killed. Application of a rooting hormone to the cut surface can help speed up the formation of adventitious roots but is not necessary for many plants. Because of the rapid growth occurring in the tissues in the spring, softwood cuttings should have significant root growth within 3 to 4 weeks.

    Softwood stem cutting with a few trimmed leaves at the top; the upper and lower nodes are labeled.
    Figure 9-22. Softwood cutting with the large leaves trimmed to reduce water loss. (Source Unknown).

    Semi-hardwood cuttings are taken in the Summer from the current season’s growth. Because of the reduces activity of the tissues it typically takes 6-12 weeks to produce roots. The process is very similar to that with the softwood. Reducing the leaf area will help reduce water loss and a misting bed should be used. A rooting hormone can be useful particular with species that are slow to root.

    Hardwood cuttings are taken in fall or winter after the plant has gone dormant. Since there are no leaves, misting is not required. Because of the lower tissue activity, a rooting hormone may be useful. While simpler that the other two since there is no misting needed, it does take significantly longer – over 12 weeks. Cutting also be should be longer than what is taken for the other two methods. Stems should be longer than 6 inches. Additionally, they can heeled-in (placed into a mound of dirt) to allow a callus to form first. A callus is a cluster of undifferentiated cells that can then be triggered to form root through application of hormones.

    Several leafless hardwood stem cuttings lying next to red-handled pruning shears.
    Figure 9-23. Hardwood cutting are taken when the plant is dormant. (Gmihail - Sopstveno delo, CC BY-SA 3.0 Link to Source [commons.wikimedia.org]).

    Root cuttings are a special type of hardwood cutting. As the name would imply, root cutting are taken from an existing plant’s root system. The root should be cut in the plant’s dormant season. A 3-6 inch sections should be removed from a health roots. At the end near the base of the plant (proximal), make a straight cut across the root. On the distal end (further away from the plant stem, make the lower cut diagonally. The two different cuts serve two purposes. First, they help you maintain the polarity of the cutting. Secondly, they diagonal cut provides more surface area for water uptake while the straight cut at the top has less surface area for water loss. When you place your cutting in the media remember the diagonal cut goes down into the media.


    This page titled 9.2.1: Cuttings from Woody Plants was last modified on Sat, 14 Nov 2026 17:10:09 GMT and is shared under a CC BY-NC-SA 4.0 license and was authored, remixed, and/or curated by Stephanie Harvey.