Learn · Gear And Gear Unit Design: Theory and Practice

Lecture 8 of 48Week 2

LECTURE 8: Design of Bevel Gear

Prof. Rathindranath Maiti · IIT Kharagpur

Credits and licence

From
Gear And Gear Unit Design: Theory and Practice, IIT Kharagpur (at NPTEL)
Licence
CC BY-NC-SA, as NPTEL states it. Non-commercial use only.
Attribution
NPTEL states: "Distributed under Creative Commons Attribution-ShareAlike / CC BY - NC - SA", beside a BY-NC-SA badge.
Who can watch
Tweens profiles and older. How courses are placed

All the lectures

  1. Lecture 1: Introduction- Motivation and Theme of the Course Video
  2. Lecture 2 : Laws of Gearing, Kinematics and Geometry Part-I Video
  3. Lecture 3 : Laws of Gearing, Kinematics and Geometry Part-II Video
  4. Lecture 4 : Involute Toothed Gear- Properties & Terminology Video
  5. Lecture 5 : Tutorial Video
  6. LECTURE 6: Involute Straight Tooth Spur Gear Video
  7. LECTURE 7: Helical Tooth Spur Gear & Loads on Gear Shaft Video
  8. LECTURE 8: Design of Bevel Gear Video
  9. LECTURE 9: Crossed Helical Gear-I Video
  10. LECTURE 10: Crossed Helical Gear-II and Worm Gear Video
  11. LECTURE 11 : Gear Unit Design - Selection of Stage Ratios, Pinion & Gear Teeth Numbers Video
  12. LECTURE 12 : Gear Unit Design - First Stage Pinion & Gear Design- I (Module on Beam Strength Basis) Video
  13. LECTURE 13 Gear Unit Design - Failure of Gear Tooth (Probable Dynamic Load and Wear Load Capacity) Video
  14. LECTURE 14 Gear Unit Design - 1st. Stage Pinion & Gear Design-II (Probable Dynamic Load and Wear Load Capacity and Finalizing 1st. Stage Pinion & Gear set) Video
  15. LECTURE 15 Gear Unit Design - 1st. Layout (After Gear Design) Video
  16. LECTURE 16 Bearing Arrangement-Gear Box Shafts Video
  17. LECTURE 17: Bearing Load Calculation- Intermediate Shaft Video
  18. LECTURE 18 Bearing Selection & Introduction to Shaft Design Verification Video
  19. LECTURE 19 Design Verification of Gear Box Shafts Video
  20. LECTURE 20 Development (Layout) of Intermediate Shaft Video
  21. LECTURE 21 : Development (Layout) of Input Shaft & Integral Pinion Video
  22. LECTURE 22 : Development (Layout) of Output Shaft and 2nd. Stage (Output) Gear Video
  23. LECTURE 23 : Development (Layout) of Output Shaft (contd.), Loads on Shaft & Bearings Video
  24. LECTURE 24 : Output Shaft-Bearing Lives Video
  25. LECTURE 25 : Design Verification of Output Shaft Video
  26. LECTURE 26 : Design Verification of Input Shaft (including Bearing Life Estimation) Video
  27. LECTURE 27 : Finalizing Design including the Sizes of the Keys Video
  28. LECTURE 28 : Development of Plan & Elevation of Gear Reduction Unit- I Video
  29. LECTURE 29 : Development of Plan & Elevation of Gear Reduction Unit- II Video
  30. LECTURE 30 : Development of Plan & Elevation of Gear Reduction Unit- III Video
  31. Lecture 31 : Video
  32. Lecture 32 : Video
  33. LECTURE 33 Involute Spur Gear Tooth Correction : Part-I Video
  34. LECTURE 34 Involute Spur Gear Tooth Correction : Part-II Video
  35. LECTURE 35 Involute Spur Gear Tooth Correction : Part-III Video
  36. LECTURE 36 Involute Spur Gear Tooth Correction : Tutorial ( Workout Example) Video
  37. LECTURE 37 Involute Spur Gear Tooth Correction : Tutorial (Workout Example-2) Video
  38. LECTURE 38 Tooth Tip Interference, Avoidance and Contact Ratio in Involute Internal Gearing Video
  39. Lecture 39 Video
  40. Lecture 40 Video
  41. Lecture 41 Video
  42. Lecture 42 Video
  43. Lecture 43 Video
  44. Lecture 44 Video
  45. Live Session 27-03-2021 Video
  46. Live Session 10-04-2021 Video
  47. Live Session 04-05-2022 Video
  48. Live Session 19-04-2022 Video