Opening the book…

This book explains how to use the Mamiya-Six IVB, a 6×6 cm folding rangefinder camera made in Japan from 1955. It is written for beginners. Each step has a photo of the part you need.
The one thing to remember: winding the film does not arm the shutter on this camera. Before every picture you must wind to the next frame and arm the shutter.
Contents
- 1 About the camera
- 2 A short history
- 3 Know your camera
- 4 Opening the camera
- 5 Setting the shutter speed
- 6 Setting the aperture
- 7 Arming and firing the shutter
- 8 Focusing
- 9 Film and checks
- 10 Loading the film
- 10.1 Step 1: Open the back
- 10.2 Step 2: Slide out the pressure plate
- 10.3 Step 3: Check the two sides
- 10.4 Step 4: Draw the paper under the flaps
- 10.5 Step 5: Push the tip into the empty spool
- 10.6 Step 6: Slide the pressure plate back in
- 10.7 Step 7: Wind a little
- 10.8 Step 8: Check it is straight, then close
- 11 Setting frame 1 and winding on
- 12 Taking a picture: checklist
- 13 Choosing the exposure
- 14 Unloading the film
- 15 Closing the camera
- 16 Using flash
- 17 Care and troubleshooting
- 18 Quick reference
- 19 Sources
About the camera
- Mamiya was founded in Tokyo in 1940. Its first camera was the folding Mamiya Six.
- The Mamiya Six focuses by moving the film, not the lens, using a wheel on the back.
- The IVB (1955) has a larger, square finder window. It uses 120 film and takes 12 square pictures per roll.
- The 1989 Mamiya 6 is a different camera. Its manual does not apply.
A short history
The Mamiya company
- 1940: Camera designer Seiichi Mamiya and his financial backer, Tsunejiro Sugawara, founded Mamiya in Tokyo in May 1940. Its first camera was the Mamiya Six, a folding 6×6 cm rangefinder.
- Lens making: In 1947 Mamiya bought a lens maker in Setagaya, Tokyo. By 1950 it was called Setagaya Koki, and its Sekor lenses went on many Mamiya cameras.
- Later cameras: Mamiya became known for professional medium-format cameras, including the C-series twin-lens cameras, the Mamiya Press (1962), the RB67 (1970), the M645 (1975), the RZ67 (1982) and the Mamiya 7 (1995).
- Ownership: In 2006 the camera business moved to Mamiya Digital Imaging. The Danish company Phase One bought a major stake in 2009 and bought Mamiya outright in 2015.
The Mamiya Six folding series
- Back focusing: Most folding cameras focus by moving the lens. Seiichi Mamiya patented a design in 1939 in which the lens stays still and the film moves. That is why the camera focuses with a wheel on the back.
- Model IV (1947): The first post-war model. It dropped the waist-level finder.
- Model V (1953): Added a second picture size, 6×4.5 cm.
- Model IVB (1955): Like the Model IV, with a new top plate and larger, square finder and rangefinder windows.
- Automat (1955): Winding the film also armed the shutter. On the IVB you must arm the shutter by hand.
- The folding Mamiya Six was sold new until about 1958, in about twelve versions.
Know your camera
These views show where each part is. The numbers match the parts list below. You do not need to learn them all now; each later step shows the one part you need.
-
Front, closed -
Front, open -
Back -
Top -
Inside, back open
Parts list
| No. | Part | What it does |
|---|---|---|
| 1 | Front-release button | Chrome button on the front of the body, just above the bed. Press it to open the camera. |
| 2 | Film winding knob | Turn it in the direction of its arrow to move the film to the next frame. |
| 3 | Frame counter | Numbered ring under the winding knob (1 to 12). |
| 4 | Film-speed memo | Small window on top of the winding knob. Set it to your film's ISO (ASA) as a reminder. It does not change the exposure. |
| 5 | Brake lever | Small knurled pin on the back, below the winding knob. Push it toward the arrow to unlock the wind. |
| 6 | Focusing wheel | Toothed wheel on the back. Roll it to focus. It moves the film, not the lens. |
| 7 | Infinity arrow | Arrow and ∞ mark above the focusing wheel. Roll toward it to focus farther away. |
| 8 | Eyepiece | Look here to frame and focus. A red patch here means this frame is already used. |
| 9 | Viewfinder window | Large window on the front. |
| 10 | Rangefinder window | Small window on the front. Keep your fingers off it. |
| 11 | Distance and depth-of-field dial | Top-plate dial. Shows the focus distance in meters and the zone that will look sharp. |
| 12 | Shutter release button | Chrome button on the top plate. Press it to take the picture. Its center takes a screw-in cable release. |
| 13 | Accessory shoe | Holds a flash, light meter or extra finder. |
| 14 | Back lock | Chrome catch on the end of the body. Slide it to open the back. |
| 15 | Red window slide | Covers the red window. Keep it closed except when setting frame 1. |
| 16 | Red window | Shows the numbers printed on the film's backing paper. |
| 17 | Lens | Olympus D.Zuiko F.C. 7.5 cm (75 mm) f/3.5. |
| 18 | Shutter speed ring | Silver front ring marked 500, 250, 100, 50, 25, 10, 5, 2, 1, B. |
| 19 | Red index line | Short red line above the speed ring. The speed under it is the one that is set. |
| 20 | Aperture lever | Small tab on the side of the shutter. Its tip points to the f-number on the scale (3.5 to 22). |
| 21 | Shutter arming lever | Toothed half-disc on the upper left of the shutter. Push it until it locks before every picture. |
| 22 | Flash socket | Brass post on the side of the shutter for a flash cord. From the front it looks like a small brass tube. |
| 23 | Flash sync lever (M-F-X) | Red lever. Use X for electronic flash. |
| 24 | Lens struts | Chrome arms that hold the lens out. Press them to close the camera. |
| 25 | Bellows | Light-tight folding sleeve. Handle with care. |
| 26 | Front bed | The cover that folds down when the camera opens. |
| 27 | Take-up chamber | Under the winding knob. The empty spool goes here. |
| 28 | Feed chamber | The new roll of film goes here. |
| 29 | Film roller | Chrome roller that guides the film. |
| 30 | Film guide flaps | Top and bottom flaps. The film and pressure plate slide under them. |
| 31 | Pressure plate | Removable plate that holds the film flat. Its arrow shows how to slide it in. |
| 32 | Spool holder | Holds each spool. Pull the knob under the camera to release it. |
Opening the camera

- Hold the camera with the top plate up and the bed facing away from you.
- Press the chrome front-release button (1) just above the bed.
- The bed drops and the lens springs forward. Guide the bed down with your hand.
- Check that both struts are straight and locked. The lens must not wobble.
Do not pull the lens out by hand, pry the bed open, or press on the bellows.
Setting the shutter speed

The shutter speed is how long the shutter stays open. You set it with the silver ring on the front of the lens.
- Find the short red line at the top of the lens. It never moves.
- Put a fingertip on the ridged edge of the silver ring.
- Turn it left or right until the number you want sits under the red line. The ring stops at 500 and at B; never force it.
- Set it exactly on a number. Set the speed before you arm the shutter.
| On the ring | Real speed | When to use it |
|---|---|---|
| 500 | 1/500 second | Bright sun, fast action |
| 250 | 1/250 second | Sunny day, people walking |
| 100 | 1/100 second | Best everyday speed hand-held |
| 50 | 1/50 second | Shade or cloudy days. Hold very still. |
| 25, 10, 5, 2 | 1/25 to 1/2 second | Indoors or dusk. Use a tripod. |
| 1 | 1 second | Night. Tripod and cable release. |
| B | Open as long as the button is held | Longer than 1 second. Tripod and cable release. |
Ignore the small black numbers behind the silver ring. Read the speed only on the silver ring.
Setting the aperture

The aperture is the size of the opening in the lens. It is shown as an f-number.
- Find the small tab on the left side of the shutter, next to the f-numbers.
- Push it with a fingertip. It slides along the scale.
- The tip of the tab points to the f-number: 3.5, 4, 5.6, 8, 11, 16, 22.
-
Before: about f/5.6 -
After sliding the tab: f/11
| Setting | Opening | Result |
|---|---|---|
| f/3.5 or f/4 | Large | Most light. Only a thin zone is sharp. |
| f/8 or f/11 | Medium | Good everyday setting. |
| f/16 or f/22 | Small | Least light. Almost everything is sharp. |
Arming and firing the shutter

Try this with no film loaded.
- Find the toothed half-disc on the upper left of the shutter. Do not confuse it with the brass tube below it; that is the flash socket.
- Push it gently in the only direction it moves, until it stops and stays there. The shutter is now armed.
- Press the chrome release button on the top plate slowly. You hear a click.
- Look into the eyepiece. A red patch means this frame is used. With film loaded, wind on when you see red.


Test every speed: open the back, point the camera at a bright window and look through the lens. Arm and fire at each speed. If slow speeds stick, fire each one 10 to 20 times. If that does not help, the shutter needs a service.
Release will not fire? Check that the shutter is armed, the struts are locked, and there is no red in the eyepiece.
Focusing


- Look through the eyepiece. In the middle you see a small, brighter patch.
- Point the patch at your subject. If it is out of focus, you see two copies of it.
- Roll the toothed wheel (6) on the back with your right thumb until the two copies merge.
- Rolling toward the arrow focuses farther away (∞).

- The dial on the top plate (11) shows the distance in meters (1 m is about 3.3 ft).
- Distances are measured from the back of the camera (the film), not from the lens.
- The U-shaped lines show what will look sharp at f/3.5, 8, 11 and 22.
- Quick street setting: f/22, focus at about 4 m. About 2 m to far away looks sharp.
- The closest focus is about 1 m. Up close, leave extra room at the top of the frame, because the finder sits above the lens.
Film and checks

- Use 120 roll film (not 35 mm or 220). You get 12 square pictures per roll.
- ISO 400 film is easiest for beginners.
- Set the film-speed reminder (4) to your film's ISO. It does not change the exposure.
- Load and unload in the shade.
Bellows light test: in a dark room, open the camera and the back. Shine a small flashlight inside the bellows and look at the outside. Any pinpoint of light is a leak. Seal tiny holes with black fabric paint; large tears need new bellows.
Loading the film
Load and unload film in the shade.
Step 1: Open the back

Slide the back lock (14) on the end of the body. Swing the back open.
Step 2: Slide out the pressure plate

The black pressure plate (31) sits under the top and bottom guide flaps (30). Slide it out sideways and set it aside. Note the arrow on it.
Step 3: Check the two sides

- The empty spool goes on the take-up side (27), under the winding knob.
- The new roll goes on the other side, the feed side (28).
- To fit a spool, pull out the knob under the camera, drop the spool in, and let the knob snap back.
Step 4: Draw the paper under the flaps

Break the paper seal on the new roll. Pull out the pointed end. Draw it across the film opening and tuck it under both guide flaps.
Step 5: Push the tip into the empty spool

Push the pointed end into the wide slot of the empty spool. The printed side of the paper faces you.
Step 6: Slide the pressure plate back in

Slide the plate back under the flaps, the way its arrow points. Push it in evenly.
Step 7: Wind a little

Turn the winding knob two or three times. The paper winds onto the take-up spool.
Step 8: Check it is straight, then close

The paper should sit straight between the spool ends. If it rubs one end, open up and reload it. Then close the back and press until the lock catches.
Setting frame 1 and winding on

- Slide the cover (15) to uncover the red window (16).
- Turn the winding knob (2) slowly in the direction of its arrow. Stop when the number 1 is centered.
- Close the red window cover right away.
- After each picture, push the brake lever (5) toward its arrow, then let go.
- Turn the winding knob until it stops by itself. If it does not stop, use the red window for each number and close the cover each time.
-
Winding direction -
Brake lever (5)
Taking a picture: checklist
- Wind to a fresh frame. No red in the eyepiece.
- Set the shutter speed under the red line.
- Set the aperture.
- Arm the shutter.
- Focus: merge the two images.
- Frame the picture. Keep fingers off the lens and the small front window.
- Breathe out. Press the release slowly.
- Wind on right away.
Hold the body in both hands. The camera has no strap lugs; use a case or a strap that screws into the tripod socket.
Choosing the exposure
The camera has no light meter. Use a hand-held meter, a phone light-meter app, or this table (the "Sunny 16" rule).
| Light | Aperture | ISO 100 film | ISO 400 film |
|---|---|---|---|
| Bright sun, sharp shadows | f/16 | 1/100 | 1/500 |
| Hazy sun, soft shadows | f/11 | 1/100 | 1/500 |
| Cloudy, light shadows | f/8 | 1/100 | 1/500 |
| Heavy overcast | f/5.6 | 1/100 | 1/500 |
| Open shade | f/4 | 1/100 | 1/500 |
Unloading the film
- After frame 12, push the brake lever and keep winding until the knob turns easily.
- Open the back in the shade. Pull out the knob under the take-up side and lift out the roll. Hold it tight.
- Fold the paper end under and seal it with the sticky tab.
- Move the empty spool to the take-up side, ready for the next roll.
Closing the camera

- Set the focus to far away (∞).
- Press both strut joints (24) inward with your thumbs.
- Fold the lens back. Check that the bellows is not caught.
- Press the bed shut until it clicks.
Never push on the lens or the speed ring to close it. Do not store the camera with the shutter armed.
Using flash

- Set the red sync lever (23) to X for an electronic flash. X works at every speed.
- Plug the flash cord into the socket (22). An old socket may need an adapter.
- The accessory shoe (13) has no electric contact, so the cord is needed.
- Aperture = flash guide number ÷ distance.
Care and troubleshooting
| Problem | Likely cause | What to do |
|---|---|---|
| Slow speeds stick | Old oil in the shutter | Fire each slow speed 10 to 20 times. If it still sticks, get a shutter service. |
| Light streaks or spots | Bellows pinholes, or red window left open | Do the bellows test. Keep the red window closed. |
| Photos soft everywhere | Struts not locked, or rangefinder out of line | Check the struts and that the images merge at ∞. |
| Two pictures on one frame | Forgot to wind | Check for red in the eyepiece before shooting. |
| Blank frame | Shutter not armed | Arm before every shot. |
| Hazy photos | Haze or fungus in the lens | Have a repair shop clean the lens. |
Store the camera closed, in a case, in a dry place. Fire the shutter every few weeks.
Quick reference
| Task | What to do |
|---|---|
| Open | Press the button above the bed. Check the struts are locked. |
| Frame 1 | Open the red window cover on the back. Wind until "1" shows. Close the cover. |
| Speed | Turn the silver ring on the lens. The number under the red line is the speed. |
| Aperture | Slide the small tab beside the f-numbers. |
| Arm shutter | Push the toothed half-disc lever until it stays. |
| Focus | Roll the wheel on the back until the two images in the finder merge. |
| Wind | Push the brake lever, then wind until it stops. Red in the finder means wind first. |
| Close | Focus to ∞. Press the struts inward. Fold the bed shut. |
Sources
- Mamiya Camera Co., Instructions for Use of the Mamiya-6 (1955 booklet).
- Wikipedia: Mamiya and Mamiya Six.
- Mike Eckman, "Mamiya 6 Model V (1953)", mikeeckman.com.
- Part locations and photos: a Mamiya-6 IVB.
The book could not be loaded just now.