22.3: Applications of Magnetic Fields

Physics: A Foundation for Scientists and Engineers · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    22.3: Applications of Magnetic Fields

    The magnetic force on moving charges is at work in instruments that changed the history of physics and in devices found in every home. This section describes five of them.

    Discovery of the Electron

    By the late nineteenth century, physicists knew that a glass tube pumped nearly empty of air, with a high voltage between two metal electrodes sealed inside it, glowed where something emitted by the negative electrode, the cathode, struck the far end of the tube. These cathode rays traveled in straight lines and cast shadows, and they could be bent by a magnet. But what were they? Some physicists thought they were a kind of wave in the ether; others, that they were particles.

    A schematic of Thomson's cathode-ray tube, drawn as a long evacuated glass tube.
    Figure 22.7. Thomson’s apparatus (schematic). Electrons from the cathode are accelerated and collimated by the anodes, then pass through crossed electric and magnetic fields. When the fields are balanced the beam goes straight; with one field alone it is deflected (dashed).
    Figure descriptionA schematic of Thomson's cathode-ray tube, drawn as a long evacuated glass tube. At the left end is the cathode; to its right, the anode, a plate with a hole, accelerates the rays, and a second plate with a slit narrows them into a beam. In the middle of the tube are two horizontal deflecting plates, the upper one positive, producing a downward electric field; the same region is filled with a magnetic field into the page, shown by crosses in circles. At the right end is a fluorescent screen. The undeflected beam travels straight through to the center of the screen; dashed paths show the beam bent up or down when only one of the fields is on.

    In 1897 J. J. Thomson settled the question at the Cavendish Laboratory in Cambridge with the apparatus sketched in Figure 22.7. The rays from the cathode were accelerated by an anode and passed through slits to form a narrow beam. The beam then passed between two deflecting plates, which could apply an electric field, and through a magnetic field at right angles to it, before striking a fluorescent screen. Thomson measured the beam’s deflection by the electric field alone (as in Figure 16.13), and then adjusted the magnetic field until the beam went straight through: the arrangement is a velocity selector, and it gave the speed of the rays, \(v = E/B\). With the magnetic field alone, the beam curves in a circle of radius \(r = mv/qB\). Substituting the speed,

    \[\frac{q}{m} = \frac{v}{rB} = \frac{E}{rB^2}. \tag{22.6}\]

    Every quantity on the right can be measured. Thomson found that cathode rays have a definite charge-to-mass ratio (Chapter 16) that is the same no matter the metal the cathode was made of or the gas that remained in the tube. The rays were particles, negatively charged, present in all matter. And their \(q/m\) was more than a thousand times larger than that of hydrogen ions, the lightest particles then known: either their charge was very large or their mass was very small. When Millikan measured the elementary charge a decade later (Example 16.12), the answer became clear. The particles, soon called electrons, have the same size of charge as a hydrogen ion and about \(1/1836\) of its mass. The atom, long assumed to be indivisible, had parts (Chapter 41).

    Example 22.6: Measuring \(e/m\)

    In a Thomson-type experiment, an electric field of \(1.5\times 10^{4}\,\mathrm{V/m}\) is balanced by a magnetic field of \(0.50\,\mathrm{mT}\). With the electric field switched off, the beam bends in a circle of radius \(34\,\mathrm{cm}\). Find the speed of the electrons and their charge-to-mass ratio.

    Solution

    The speed is \(v = E/B = (1.5\times10^{4})/(0.50\times10^{-3}) = \boxed{3.0\times 10^{7}\,\mathrm{m/s}}\), a tenth of the speed of light. Then

    \[\frac{e}{m} = \frac{E}{rB^2} = \frac{1.5\times10^{4}}{(0.34)(0.50\times10^{-3})^2} = \boxed{1.8\times 10^{11}\,\mathrm{C/kg}},\]

    in agreement with the modern value, \(1.76\times 10^{11}\,\mathrm{C/kg}\). The accelerating voltage that gave the electrons this speed follows from \(eV = \frac{1}{2}mv^2\): about \(2.6\,\mathrm{kV}\).

    Cyclotrons and Synchrotrons

    To probe the atomic nucleus, physicists needed beams of particles with energies of millions of electron volts. Producing such energies with a single voltage is very difficult. In 1931 Ernest Lawrence found a way around the problem: give the particles many small kicks instead of one big one, and use a magnetic field to bring them back for each kick.

    Cyclotron from above: two D-shaped electrodes in a magnetic field, with a spiral particle path.
    Figure 22.8. A cyclotron, seen from above. The magnetic field bends the particles into semicircles inside the dees, and the oscillating voltage accelerates them each time they cross the gap. Because the orbital period does not depend on speed, one fixed frequency keeps them in step.
    Figure descriptionA top view of a cyclotron. Two D-shaped hollow electrodes, the dees, face each other across a narrow gap, forming a circle. A uniform magnetic field points into the page. An oscillating voltage source, drawn below as a circle with a wavy line, is connected to both dees. A particle released near the center follows a spiral path made of semicircles of steadily increasing radius, crossing the gap twice per revolution and gaining energy at each crossing, until it leaves the edge of the dees as the output beam.

    A cyclotron consists of two hollow, D-shaped metal electrodes (called “dees”), in a vacuum chamber between the poles of a large electromagnet (Figure 22.8). An oscillating voltage is applied between the dees. Inside each dee there is no electric field, and a charged particle simply travels in a semicircle under the magnetic force. Each time it crosses the gap between the dees, the voltage has reversed, and the particle is accelerated again. With each crossing its speed increases and it moves out to a semicircle of larger radius. But by equation (22.3), the time for each semicircle is the same, so if the voltage oscillates at the cyclotron frequency \(f = qB/2\pi m\), the particle arrives at the gap in step with the voltage every time. The particle spirals outward until it reaches the edge of the dees at radius \(R\), with speed \(v = qBR/m\) and kinetic energy

    \[K = \frac{1}{2}mv^2 = \frac{q^2B^2R^2}{2m}. \tag{22.7}\]

    Example 22.7: A proton cyclotron

    A cyclotron with dees of radius \(0.50\,\mathrm{m}\) in a field of \(1.5\,\mathrm{T}\) accelerates protons. Find (a) the frequency of the oscillating voltage, (b) the protons’ final kinetic energy, and (c) the number of revolutions they make if they gain \(50\,\mathrm{keV}\) at each gap crossing.

    Solution

    (a) The cyclotron frequency is

    \[f = \frac{eB}{2\pi m_p} = \frac{(1.602\times10^{-19})(1.5)}{2\pi(1.673\times10^{-27})} = \boxed{23\,\mathrm{MHz}},\]

    a radio frequency.

    (b) From equation (22.7),

    \[K = \frac{e^2B^2R^2}{2m_p} = \frac{(1.602\times10^{-19})^2(1.5)^2(0.50)^2}{2(1.673\times10^{-27})} = 4.3\times 10^{-12}\,\mathrm{J} = \boxed{27\,\mathrm{MeV}}.\]

    (c) Each revolution includes two gap crossings, worth \(100\,\mathrm{keV}\), so reaching \(27\,\mathrm{MeV}\) takes about \(\boxed{270}\) revolutions. A modest voltage, used hundreds of times, produces an energy that would need tens of millions of volts to reach in one step.

    Synchrotron from above, not to scale: a circular beam pipe ringed by bending magnets.
    Figure 22.9. A synchrotron, seen from above (not to scale). Bending magnets hold the particles on a ring of fixed radius, and an accelerating cavity gives them a kick on every lap. As their momentum grows, the magnets’ field is raised in step so that \(r = p/|q|B\) stays the same. Electrons bent by the magnets give off synchrotron light along the direction they are moving, tangent to the ring.
    Figure descriptionA synchrotron seen from above, not to scale. A circular beam pipe carries the particles counterclockwise, shown by arrows along the ring. Seven bending magnets sit around the ring, each marked with a cross in a circle because its field points into the page. At the top of the ring is an accelerating cavity with an oscillating electric field. Particles enter from an injector at the lower left, joining the ring tangentially at the bottom. From two of the bending magnets at the lower right, pale wedges of synchrotron light leave tangent to the ring, toward experiments. The center of the ring is labeled beam, r equals p over the magnitude of q times B.

    Cyclotrons are still used to make the short-lived radioactive isotopes for medical imaging and to deliver proton beams for cancer therapy. But they have a limit. The protons of Example 22.7 end with a speed of \(7.2\times 10^{7}\,\mathrm{m/s}\), about a quarter of the speed of light, and at such speeds the relativistic mass effects of Chapter 35 lengthen the orbital period, so the particles fall out of step with the voltage. The cure is to change the field or the frequency as the particles speed up.

    Synchrotrons. In a synchrotron the particles travel around a ring of fixed radius, a narrow evacuated pipe threading a sequence of bending magnets (Figure 22.9), and are accelerated by electric fields at a few points around the ring. As the particles gain energy, the magnetic field is increased in step, or in synchrony, to keep them on the same circle. Equation (22.2), written as \(r = p/|q|B\), remains exactly correct at relativistic speeds provided \(p\) is the relativistic momentum \(\gamma mv\) (equation (35.9)). The largest synchrotron is the Large Hadron Collider near Geneva.

    Example 22.8: The Large Hadron Collider

    The LHC is designed to bring protons to an energy of \(7.0\,\mathrm{TeV}\) in bending magnets with a field of \(8.3\,\mathrm{T}\). At this energy the proton’s momentum is essentially \(p = E/c\). What is the radius of curvature of the protons’ path?

    Solution

    The momentum is

    \[p = \frac{E}{c} = \frac{(7.0\times10^{12})(1.602\times10^{-19}\,\mathrm{J})}{3.00\times10^{8}\,\mathrm{m/s}} = 3.7\times 10^{-15}\,\mathrm{kg\cdot m/s},\]

    so

    \[r = \frac{p}{eB} = \frac{3.7\times10^{-15}}{(1.602\times10^{-19})(8.3)} = \boxed{2.8\,\mathrm{km}}.\]

    The bending magnets, more than a thousand of them each \(15\,\mathrm{m}\) long, fill about two-thirds of the 27-kilometer ring; the rest holds the accelerating cavities, focusing magnets, and detectors. The ring is so large because even the strongest practical magnets can bend such energetic protons only gently.

    Note: Synchrotron radiation

    A charged particle moving in a circle is accelerating, and accelerating charges radiate electromagnetic waves (Chapter 27). For protons this loss is small, but electrons, far lighter, radiate intensely when they are bent at high energy. This synchrotron radiation limits how much energy electron synchrotrons can reach, but it is also enormously useful: dedicated electron storage rings around the world, called light sources, produce intense beams of x-rays for studying the structure of proteins, materials, and ancient artifacts.

    Magnetic Force on a Current-Carrying Wire

    Vertical wire of length L carrying current up through a magnetic field into the page.
    Figure 22.10. A wire carrying current \(I\) upward through a magnetic field directed into the page is pushed to the left. The electrons (blue) drift downward, and the magnetic force on each of them points left; they carry the wire with them.
    Figure descriptionA vertical straight wire of length L in a uniform magnetic field pointing into the page, shown as a lightly shaded region with a cross in a circle at each corner. The wire extends above and below the field region, and L is the length inside it. The current I flows upward. The magnetic force on the wire, F equals I L cross B, points to the left, perpendicular to both the wire and the field. Small electrons inside the wire drift downward, opposite to the current, and each feels a force to the left as well.

    A current is a stream of moving charges, so a magnetic field exerts a force on a wire that carries a current. Consider a straight segment of wire of length \(L\) and cross-sectional area \(A\), carrying current \(I\) in a uniform field \(\vec{B}\) (Figure 22.10). Each charge carrier moves with the drift velocity \(\vec{v}_d\) and feels a force \(q\vec{v}_d\times\vec{B}\). The segment contains \(nAL\) carriers, where \(n\) is the number per unit volume, so the total force is

    \[\vec{F} = (q\vec{v}_d\times\vec{B})\,nAL = (nqv_dA)\,\vec{L}\times\vec{B},\]

    where \(\vec{L}\) is a vector of length \(L\) pointing along the wire in the direction of the current. From Chapter 20, \(nqv_dA = I\) (equation (20.3)), so

    Key Equation: Magnetic force on a current-carrying wire

    \[\vec{F} = I\vec{L}\times\vec{B}, \qquad F = ILB\sin\theta. \tag{22.8}\]

    Here \(\theta\) is the angle between the wire and the field. The result does not depend on the sign of the carriers: electrons drifting one way and positive charges drifting the other both give the same force for the same current. The force on the carriers is passed to the wire itself, since the carriers cannot leave it. For a wire that is curved, or a field that is not uniform, divide the wire into short pieces \(d\vec{L}\), each feeling a force \(d\vec{F} = I\,d\vec{L}\times\vec{B}\), and add them up. For a closed loop of any shape in a uniform field, the forces add to zero; but, as the next section shows, they can still exert a torque.

    Example 22.9: Levitating a wire

    A horizontal copper wire of diameter \(1.0\,\mathrm{mm}\) runs east–west, perpendicular to a horizontal magnetic field. What current makes the magnetic force support the wire’s weight (a) in a laboratory field of \(0.10\,\mathrm{T}\), and (b) in Earth’s field, taking its horizontal component to be \(2.0\times 10^{-5}\,\mathrm{T}\)? (The density of copper is \(8.96\times 10^{3}\,\mathrm{kg/m^3}\).)

    Solution

    The mass per unit length is \(\lambda = \rho A = (8.96\times10^{3})\pi(0.50\times10^{-3})^2 = 7.0\times 10^{-3}\,\mathrm{kg/m}\). For a length \(L\), the force must balance the weight: \(ILB = \lambda Lg\), so \(I = \lambda g/B\).

    (a) \(I = (7.0\times10^{-3})(9.8)/0.10 = \boxed{0.69\,\mathrm{A}}\).

    (b) \(I = (7.0\times10^{-3})(9.8)/(2.0\times10^{-5}) = \boxed{3.4\times 10^{3}\,\mathrm{A}}\). Such a current would melt the thin wire almost at once (Section 20.4). Earth’s field is far too weak to levitate wires, although the force it exerts on power lines is measurable. The current must flow in the right direction, too: the force \(I\vec{L}\times\vec{B}\) must point up.

    Checkpoint 22.3

    A straight wire carries a current due east through a uniform magnetic field. What is the direction of the force on the wire if the field points (a) due north, (b) straight up, (c) due east?

    Answer

    Torque on a Current Loop

    Although the net force on a current loop in a uniform field is zero, the forces on different sides need not act along the same line, and so they can exert a torque. This torque turns every electric motor.

    Two views of a rectangular current loop in a uniform magnetic field B pointing to the right.
    Figure 22.11. Torque on a current loop. (a) Seen from the side, the forces on the two sides of length \(a\) are equal and opposite but do not act along the same line. (b) Seen from above, they form a couple with lever arm \((b/2)\sin\theta\) each, which turns the magnetic moment \(\vec{\mu}\) toward the direction of \(\vec{B}\).
    Figure descriptionTwo views of a rectangular current loop in a uniform magnetic field B pointing to the right. Panel a, a perspective view from the side: the loop is a vertical rectangle that can rotate about a vertical axis through its center. Current I circulates around it. The two vertical sides, of length a, feel magnetic forces F of equal size in opposite directions, one out of the page and one into the page. Panel b, a view from above, looking down the axis: the loop appears edge-on as a line segment of width b through the axis. At one end of the segment the current comes out of the page, shown as a dot, and the force on it points up the page; at the other end the current goes into the page, shown as a cross, and the force on it points down. The magnetic moment mu is drawn perpendicular to the segment, making an angle theta with B. The forces form a couple that turns mu toward B.

    Take a rectangular loop with sides \(a\) and \(b\), carrying current \(I\), free to turn about an axis through its center, in a uniform field \(\vec{B}\) perpendicular to the axis (Figure 22.11). The two sides of length \(a\) run perpendicular to \(\vec{B}\), so each feels a force of magnitude \(IaB\), in opposite directions, perpendicular both to the side and to the field. The other two sides feel forces along the axis, which cancel and produce no torque. Let \(\theta\) be the angle between the field and the normal to the plane of the loop. The lever arm of each of the two forces about the axis is \((b/2)\sin\theta\), so the total torque is

    \[\tau = 2\,(IaB)\,\frac{b}{2}\sin\theta = IabB\sin\theta = IAB\sin\theta,\]

    where \(A = ab\) is the area of the loop. The result holds for a flat loop of any shape. For a coil of \(N\) turns, the torque is \(N\) times larger.

    The magnetic dipole moment. All the properties of the loop that matter here, its current, its area, its number of turns, and its orientation, can be collected in a single vector, the magnetic dipole moment:

    Key Equation: Magnetic dipole moment of a current loop

    \[\vec{\mu} = NIA\,\hat{n}, \tag{22.9}\]

    where \(\hat{n}\) is the unit vector normal to the loop, with direction given by another right-hand rule: curl the fingers of your right hand around the loop in the direction of the current, and your thumb points along \(\hat{n}\). The unit of \(\mu\) is the \(\,\mathrm{A\cdot m^2}\). The torque and the potential energy then take exactly the forms we found for an electric dipole in an electric field (Section 16.5), with \(\vec{\mu}\) in place of \(\vec{p}\) and \(\vec{B}\) in place of \(\vec{E}\):

    Key Equation: Torque and energy of a magnetic dipole

    \[\vec{\tau} = \vec{\mu}\times\vec{B}, \qquad U = -\vec{\mu}\cdot\vec{B}. \tag{22.10}\]

    The torque always tends to turn \(\vec{\mu}\) toward \(\vec{B}\), and the potential energy is lowest, \(-\mu B\), when \(\vec{\mu}\) points along the field. A compass needle is a small magnetic dipole, and it swings to line up with Earth’s field for exactly this reason. The same is true of atoms, electrons, and nuclei, all of which have magnetic moments (Chapter 23); lining up the moments of hydrogen nuclei in a strong field is the first step in making an MRI image.

    A simple direct-current motor in perspective.
    Figure 22.12. A simple DC motor. The battery drives current through fixed brushes into a split-ring commutator that turns with the coil. The forces on the two sides of the coil parallel to the axis are opposite, so they turn the coil. Every half turn the commutator halves trade brushes, reversing the current in the coil, so the torque keeps turning it the same way.
    Figure descriptionA simple direct-current motor in perspective. A north magnetic pole block, N, is at the left and a south pole block, S, at the right, with magnetic field lines B running from N to S across the gap. A flat rectangular coil lies horizontally in the gap and can rotate about an axis that runs from front to back through its center. On the right side of the coil the current I flows toward the back and the magnetic force F points down; on the left side the current flows toward the front and the force points up, so the coil turns. At the front, the two ends of the coil connect to the two halves of a split ring, the commutator, mounted on the axis. Two fixed brushes press on the commutator from the left and right, and wires run from the brushes down to a battery below.

    Electric motors. In an electric motor, a coil on a rotating shaft sits in a magnetic field. The torque turns the coil toward alignment, but just as \(\vec{\mu}\) lines up with \(\vec{B}\), a sliding contact called a commutator reverses the current in the coil. The moment now points the other way, and the torque keeps the coil turning in the same direction for another half turn, when the current reverses again. The commutator is a ring on the shaft split into two halves, one connected to each end of the coil, and two fixed brushes press on it to carry current in from the battery (Figure 22.12). Each time the coil passes alignment, the halves swap brushes, and that swap is what reverses the current. Practical motors use many coils at different angles, so that the torque is nearly constant, and in modern “brushless” motors the reversal is done electronically.

    Example 22.10: The torque on a motor coil

    A rectangular coil of 100 turns, \(4.0\,\mathrm{cm}\) by \(6.0\,\mathrm{cm}\), carries \(2.0\,\mathrm{A}\) in a field of \(0.50\,\mathrm{T}\). Find (a) its magnetic moment, (b) the largest torque on it, and (c) the work needed to turn it from the orientation of lowest energy to that of highest energy.

    Solution

    (a) \(\mu = NIA = (100)(2.0)(0.040)(0.060) = \boxed{0.48\,\mathrm{A\cdot m^2}}\).

    (b) The torque is largest when \(\vec{\mu}\) is perpendicular to \(\vec{B}\): \(\tau_{\max} = \mu B = (0.48)(0.50) = \boxed{0.24\,\mathrm{N\cdot m}}\).

    (c) \(U\) ranges from \(-\mu B\) to \(+\mu B\), so the work is \(2\mu B = \boxed{0.48\,\mathrm{J}}\).

    The Hall Effect

    When a current flows through a conductor in a magnetic field, the magnetic force pushes the moving charge carriers toward one side of the conductor. In 1879 Edwin Hall, a graduate student at Johns Hopkins, detected the result: a small voltage across the conductor, perpendicular both to the current and to the field. The Hall effect gives a direct way to measure magnetic fields, and it answers a question that nothing in Chapter 20 could: what is the sign of the charge carriers?

    Two panels of a conducting strip carrying current in a magnetic field, showing the Hall effect.
    Figure 22.13. The Hall effect in a strip carrying current \(I\) to the right, with \(\vec{B}\) into the page. The magnetic force pushes the carriers toward the top edge whatever their sign. (a) Positive carriers make the top edge positive. (b) Negative carriers make it negative. The sign of the Hall voltage reveals the sign of the carriers.
    Figure descriptionTwo panels, each showing a flat horizontal conducting strip of width w carrying current I to the right, in a magnetic field pointing into the page, shown by crosses in circles. Panel a, positive carriers: the carriers drift to the right and the magnetic force pushes them up, so positive charge collects along the top edge and negative charge along the bottom edge; the Hall field E sub H points down. Panel b, negative carriers: electrons drift to the left, and the magnetic force pushes them up too, so negative charge collects along the top edge and positive charge along the bottom; the Hall field points up. In both panels a voltmeter connected between the top and bottom edges reads the Hall voltage V sub H, with opposite signs in the two cases.

    Consider a flat strip of width \(w\) and thickness \(t\), carrying current \(I\) along its length, in a field \(\vec{B}\) perpendicular to its face (Figure 22.13). Suppose first that the carriers are positive, drifting in the direction of the current. The force \(q\vec{v}_d\times\vec{B}\) pushes them toward one edge of the strip, which becomes positively charged, while the opposite edge is left negative. The separated charges set up a transverse electric field \(E_H\) across the strip, which pushes back on the carriers. Charge builds up until the electric force balances the magnetic force, \(qE_H = qv_dB\). The potential difference across the width of the strip is then the Hall voltage, \(V_H = E_Hw = v_dBw\). Using \(I = nqv_dA\) with \(A = wt\) to eliminate the drift speed,

    Key Equation: Hall voltage

    \[V_H = \frac{IB}{nqt}. \tag{22.11}\]

    If the carriers are negative, drifting against the current, the magnetic force on them points toward the same edge (both \(q\) and \(\vec{v}_d\) change sign), so now negative charge collects there, and the Hall voltage has the opposite sign. The sign of the Hall voltage reveals the sign of the carriers. For most metals it confirms that the carriers are electrons. But for some metals, and for p-type semiconductors, the Hall voltage has the positive sign: the current is carried by “holes,” missing electrons that behave like positive charges. Once the sign is known, the size of \(V_H\) gives the carrier density \(n\).

    Example 22.11: Hall voltages in a metal and a semiconductor

    (a) A copper strip \(0.10\,\mathrm{mm}\) thick carries \(10\,\mathrm{A}\) in a field of \(1.0\,\mathrm{T}\) perpendicular to its face. Find the Hall voltage. (\(n = 8.49\times 10^{28}\,\mathrm{m^{-3}}\).) (b) Repeat for a semiconductor strip of the same thickness with \(n = 1.0\times 10^{22}\,\mathrm{m^{-3}}\), carrying only \(1.0\,\mathrm{mA}\).

    Solution

    (a) For the copper strip,

    \[V_H = \frac{IB}{nqt} = \frac{(10)(1.0)}{(8.49\times10^{28})(1.602\times10^{-19})(1.0\times10^{-4})} = \boxed{7.4\,\mathrm{\mu V}},\]

    tiny even for a large current and a strong field.

    (b) For the semiconductor,

    \[V_H = \frac{(1.0\times10^{-3})(1.0)}{(1.0\times10^{22})(1.602\times10^{-19})(1.0\times10^{-4})} = \boxed{6.2\,\mathrm{mV}},\]

    nearly a thousand times larger with ten thousand times less current. Because a semiconductor has so few carriers, they must drift much faster to carry a current, and the magnetic force on them is correspondingly larger. This is why practical Hall sensors are made of semiconductors.

    Hall sensors are everywhere: they are the magnetometers that let a phone act as a compass, they sense the position of the rotor in brushless motors, they measure wheel speed for a car’s antilock brakes, and they detect whether a laptop’s lid is closed. Because \(V_H\) is proportional to \(B\), a calibrated Hall probe is also the standard laboratory instrument for measuring magnetic fields.

    Checkpoint 22.4

    A Hall probe is held in a field and gives a reading of \(+2.0\,\mathrm{mV}\). (a) The probe is turned over, so the field passes through it in the opposite direction. What does it read? (b) The probe is rotated so that its face is parallel to the field. What does it read?

    Answer

    Answers to Checkpoints

    Checkpoint 22.3. Use \(\vec{F} = I\vec{L}\times\vec{B}\) with \(\vec{L}\) pointing east. Take east as \(+x\), north as \(+y\), and up as \(+z\). (a) \(\hat\imath\times\hat\jmath = \hat{k}\): the force points straight up. (b) \(\hat\imath\times\hat{k} = -\hat\jmath\): the force points due south. (c) The current is parallel to the field, so the cross product is zero: there is no force. In every case the force is perpendicular to both the wire and the field.

    Checkpoint 22.4. (a) \(-2.0\,\mathrm{mV}\). The Hall voltage is proportional to the component of \(\vec{B}\) perpendicular to the probe’s face, and turning the probe over reverses that component, so the reading changes sign. (b) Zero. With its face parallel to the field, the field has no component perpendicular to the face, so the carriers feel no sideways force and no Hall voltage builds up. This is how a Hall probe is used to find the direction of a field: rotate it until the reading is largest.


    This page titled 22.3: Applications of Magnetic Fields was last modified on Thu, 12 Nov 2026 04:27:02 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.