23.5: Solenoids and Toroids

Physics: A Foundation for Scientists and Engineers · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    23.5: Solenoids and Toroids
    Computed magnetic field lines of a ten-turn solenoid, in a plane through its axis.
    Figure 23.9. Computed field lines of a solenoid, in a plane through its axis. The current comes out of the page along the top and goes into it along the bottom. Inside, the field is strong and nearly uniform; outside it is weak; and beyond the ends it resembles the field of a bar magnet.
    Figure descriptionComputed magnetic field lines of a solenoid of ten turns, seen in cross-section, with its axis horizontal. The turns appear as two rows of wire cross-sections: along the top row the current comes out of the page, and along the bottom row it goes into the page. Inside the coil the field lines run straight, parallel, and evenly spaced from left to right. They emerge from the right end, spread out, and curve back around the outside of the coil, far apart, to re-enter the left end.

    A solenoid is a long wire wound into a tight helical coil. It is the most practical way to produce a strong, uniform magnetic field, and it appears in everything from doorbells and car starters to MRI scanners. Each turn is nearly a circular loop, and the fields of all the turns add. Figure 23.9 shows the computed field lines of a solenoid of ten turns. Inside, the fields of the turns reinforce each other and the field lines are nearly straight, parallel, and evenly spaced: the field is strong and uniform. Outside, the lines spread through all the space around the coil, and the field is weak. Beyond the ends, the pattern is that of a bar magnet: a solenoid is a magnetic dipole whose north pole is the end from which the field lines emerge.

    A cross-section of a long ideal solenoid with its axis horizontal.
    Figure 23.10. Applying Ampère’s law to an ideal solenoid. Only the side \(ab\), inside the solenoid, contributes to \(\oint\vec{B}\cdot d\vec{s}\). The loop encloses \(n\ell\) turns.
    Figure descriptionA cross-section of a long ideal solenoid with its axis horizontal. The top row of wire cross-sections carries current out of the page, and the bottom row carries current into the page. Inside the solenoid, uniform field lines B point to the right. A rectangular Ampèrian loop a b c d is drawn with its bottom side a b, of length ell, inside the solenoid along the field, its top side c d outside the solenoid above the top row of wires, and its vertical sides b c and d a crossing the top row of wires. The loop is traversed counterclockwise, from a to b to c to d.

    The ideal solenoid. For a solenoid that is long compared with its diameter and tightly wound, the field inside is uniform and parallel to the axis, and the field outside is negligible. Ampère’s law then gives the field inside. Take a rectangular Ampèrian loop \(abcd\) with side \(ab\) of length \(\ell\) inside the solenoid, parallel to the axis, and side \(cd\) outside (Figure 23.10). Along \(ab\), \(\vec{B}\) is parallel to \(d\vec{s}\) and contributes \(B\ell\). Along \(bc\) and \(da\), \(\vec{B}\) is perpendicular to the path inside the solenoid and zero outside it, so they contribute nothing; and along \(cd\), \(B = 0\). So \(\oint\vec{B}\cdot d\vec{s} = B\ell\). If the solenoid has \(n\) turns per unit length, the loop encloses \(n\ell\) turns, each carrying current \(I\), so \(I_{\text{enc}} = n\ell I\). Ampère’s law gives \(B\ell = \mu_0 n\ell I\):

    Key Equation: Field inside an ideal solenoid

    \[B = \mu_0 nI. \tag{23.9}\]

    The field does not depend on the solenoid’s diameter or on the position inside it. It depends only on the current and on how closely the turns are wound. The direction inside follows the right-hand rule for loops: curl your fingers along the current in the turns, and your thumb points along \(\vec{B}\).

    Toroid seen from above: a ring-shaped core wound with many turns of wire.
    Figure 23.11. A toroid, seen from above. Inside the windings, the field lines are circles, and \(B = \mu_0 NI/2\pi r\). In the central hole and outside the toroid, the field is zero.
    Figure descriptionA toroid seen from above: a ring-shaped core, drawn as an annulus between two circles, wound around with many turns of wire, shown as short lines crossing the annulus radially. A dashed circular Ampèrian loop of radius r runs around inside the core, with field arrows B tangent to it, circulating counterclockwise. The windings are labeled N turns. The central hole and the region outside the toroid are labeled B equals zero.
    Example 23.7: An MRI magnet

    The main magnet of an MRI scanner is a superconducting solenoid producing a field of \(1.5\,\mathrm{T}\). If it is wound with \(2000\) turns per meter, what current does it carry? What would it take to produce the same field with an ordinary copper winding?

    Solution

    \[I = \frac{B}{\mu_0 n} = \frac{1.5}{(4\pi\times10^{-7})(2000)} = \boxed{600\,\mathrm{A}}.\]

    In a superconducting wire this current flows with no resistance at all (Chapter 20), and once established it circulates for years with the power supply disconnected. A copper winding carrying \(600\,\mathrm{A}\) through kilometers of wire would dissipate megawatts as heat, and would need a cooling plant of its own. Keeping the superconducting wire below its critical temperature is why MRI scanners are filled with liquid helium.

    Toroids. Bend a solenoid around into a closed ring, like a doughnut, and it becomes a toroid (Figure 23.11). By symmetry, the field lines inside are circles centered on the toroid’s axis. Take a circular Ampèrian loop of radius \(r\) inside the windings. It encloses all \(N\) turns, each carrying \(I\) in the same direction, so \(B(2\pi r) = \mu_0 NI\), and

    Key Equation: Field inside a toroid

    \[B = \frac{\mu_0 NI}{2\pi r}. \tag{23.10}\]

    Unlike the solenoid’s, the toroid’s field is not uniform: it is stronger near the inner edge. A circular loop in the central hole encloses no current, and one outside the toroid encloses each turn twice, once going up and once coming down, for a net of zero; in both regions \(B = 0\). An ideal toroid confines its field completely. Toroidal coils are used in transformers and in fusion reactors called tokamaks, where the field holds a ring of hot plasma away from the walls.

    Checkpoint 23.4

    (a) A solenoid’s length is doubled, keeping the same number of turns and the same current. What happens to the field inside? (b) What if instead the number of turns is doubled along with the length? (c) Why is the field of a toroid stronger near its inner edge than near its outer edge?

    Answer

    Answers to Checkpoints

    Checkpoint 23.4. (a) \(B = \mu_0 nI\) with \(n = N/L\). Doubling \(L\) with the same \(N\) halves \(n\), so the field inside halves. (b) Doubling both \(N\) and \(L\) leaves \(n\) unchanged, so the field is unchanged: only the number of turns per unit length matters, not the solenoid’s overall size. (c) Inside a toroid, \(B = \mu_0NI/2\pi r\). Every Ampèrian circle inside encloses the same current \(NI\), but a circle at the inner edge is shorter, so the same total \(\oint\vec{B}\cdot d\vec{s}\) requires a larger \(B\) there.


    This page titled 23.5: Solenoids and Toroids was last modified on Thu, 12 Nov 2026 04:26:50 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.