Opening the book…
Nearly every substance expands when it is heated. Bridges are built with expansion joints, gaps that let the roadway lengthen on a hot afternoon without buckling; power lines sag lower in summer than in winter; and a metal jar lid stuck fast can be loosened by running hot water over it, because the metal lid expands more than the glass jar.
The reason is microscopic. The atoms of a solid are held near their neighbors by forces that act like stiff springs, and they vibrate about their equilibrium positions. The potential energy of a pair of neighboring atoms is not a symmetric bowl, though: it rises very steeply if the atoms are pushed together and only gently if they are pulled apart (Figure 36.3). As the temperature rises the vibration grows, and because the well is lopsided, the atoms spend more of their time farther apart than closer together. The average spacing increases, and the whole object grows. (We look at where this potential energy curve comes from in Chapter 42.)
For a rod or any other long object, the change in length is proportional to the original length and to the temperature change:
Key Equation: Linear thermal expansion
\[\Delta L = \alpha L_0\,\Delta T. \tag{36.3}\]
The constant \(\alpha\) is the coefficient of linear expansion, a property of the material with units of \(\,\mathrm{K^{-1}}\) (Table 36.1). It is small: a steel rod one meter long grows by only about \(0.012\,\mathrm{mm}\) for each kelvin of warming. Equation (36.3) applies to every linear dimension of an object, its length, width, and thickness alike, and to the size of any hole in it.
| Solid | \(\alpha\) (\(10^{-6}\,\,\mathrm{K^{-1}}\)) | Liquid or gas | \(\beta\) (\(10^{-4}\,\,\mathrm{K^{-1}}\)) |
|---|---|---|---|
| Aluminum | \(24\) | Ethanol | \(11.2\) |
| Brass | \(19\) | Gasoline | \(9.5\) |
| Copper | \(17\) | Glycerin | \(4.9\) |
| Steel | \(12\) | Water (\(20^{\circ}\mathrm{C}\)) | \(2.1\) |
| Concrete | \(12\) | Mercury | \(1.8\) |
| Glass (ordinary) | \(9\) | Air (\(0^{\circ}\mathrm{C}\)) | \(36.7\) |
| Glass (Pyrex) | \(3.2\) | ||
| Invar (iron–nickel alloy) | \(0.9\) |
Example 36.2: Gaps between rails
Steel rails \(12.0\,\mathrm{m}\) long are laid on a cool day at \(10^{\circ}\mathrm{C}\). The hottest the rails are expected to get in summer sun is \(45^{\circ}\mathrm{C}\). How large a gap must be left between neighboring rails so that they just touch on the hottest day?
Solution
Each rail lengthens by
\[\Delta L = \alpha L_0\,\Delta T = (12\times10^{-6}\,\mathrm{K^{-1}})(12.0\,\mathrm{m})(35\,\mathrm{K}) = 5.0\times 10^{-3}\,\mathrm{m} = \boxed{5.0\,\mathrm{mm}}.\]
Each rail grows by half this amount at either end, and so does its neighbor, so a gap of \(5.0\,\mathrm{mm}\) between rail ends just closes. The steady click of a train over rail joints is the sound of these gaps.
Area and Volume Expansion
If every length grows by the factor \((1 + \alpha\,\Delta T)\), an area grows by that factor squared and a volume by that factor cubed. Because \(\alpha\,\Delta T\) is tiny (around \(10^{-4}\) or less), its square and cube are negligible, and
\[(1 + \alpha\,\Delta T)^2 \approx 1 + 2\alpha\,\Delta T, \qquad (1 + \alpha\,\Delta T)^3 \approx 1 + 3\alpha\,\Delta T.\]
So an area expands as \(\Delta A = 2\alpha A_0\,\Delta T\), and a volume as
Key Equation: Volume thermal expansion
\[\Delta V = \beta V_0\,\Delta T, \qquad \beta \approx 3\alpha \text{ for a solid}. \tag{36.4}\]
Liquids have no fixed shape, so only their coefficient of volume expansion \(\beta\) means anything. Table 36.1 shows that liquids typically expand ten to a hundred times more than solids, which is the principle of the liquid-in-glass thermometer: the liquid swells faster than its glass tube, so it climbs the narrow bore.
A heated object expands like a photographic enlargement: every dimension scales by the same factor. That includes the empty spaces. A hole in a metal plate gets larger when the plate is heated, exactly as a circle drawn on the plate would, because the metal that would fill the hole would expand too. This is why a tight steel ring can be fitted onto a shaft by heating the ring first.
Example 36.3: An overflowing gas tank
A steel gas can is filled to the brim with \(20.0\,\mathrm{L}\) of gasoline on a cool morning at \(10^{\circ}\mathrm{C}\) and left in the sun, where both warm to \(40^{\circ}\mathrm{C}\). How much gasoline spills out? Use Table 36.1.
Solution
Both the gasoline and the can expand, and the spill is the difference. The gasoline’s volume grows by
\[\Delta V_{\rm gas} = \beta_{\rm gas}V_0\,\Delta T = (9.5\times10^{-4})(20.0\,\mathrm{L})(30\,\mathrm{K}) = 0.570\,\mathrm{L}.\]
The inside of the can expands as if it were solid steel, with \(\beta_{\rm steel} = 3\alpha = 3.6\times 10^{-5}\,\mathrm{K^{-1}}\):
\[\Delta V_{\rm can} = (3.6\times10^{-5})(20.0\,\mathrm{L})(30\,\mathrm{K}) = 0.0216\,\mathrm{L}.\]
The spill is
\[\Delta V_{\rm gas} - \Delta V_{\rm can} = 0.570 - 0.022 \approx \boxed{0.55\,\mathrm{L}},\]
more than half a liter. The can’s own expansion helps only a little, because steel expands about \(25\) times less than gasoline. That is why fuel cans and car tanks are never filled to the very top.
Checkpoint 36.2
A steel washer has a hole in its center. The washer is heated by \(100\,\mathrm{K}\). Does the hole get larger, get smaller, or stay the same size? Does the answer change if the washer is made of aluminum instead?
Different expansion coefficients can be put to work. A bimetallic strip is two thin strips of different metals, say brass and steel, bonded together along their length. When it is heated the brass lengthens more than the steel, and since the two are bonded, the strip must curl. Old-fashioned thermostats used a coiled bimetallic strip to tip a switch; the same principle still trips the circuit breakers in many homes when a wire carries too much current and warms.
Checkpoint 36.3
A straight brass–steel bimetallic strip is heated. Toward which metal does it bend: is the brass on the inside of the curve or on the outside? What happens if the strip is instead cooled below the temperature at which it was straight?
Thermal Stress
If an object is prevented from expanding, it pushes on whatever holds it. Clamp a rod between two rigid walls and heat it. The rod “wants” to grow by \(\Delta L = \alpha L_0\,\Delta T\), so the walls must squeeze it back by exactly that amount. In Chapter 12 we found that compressing a rod by \(\Delta L\) requires a stress \(F/A = Y\,\Delta L/L_0\), where \(Y\) is Young’s modulus. Substituting the thermal \(\Delta L\), the thermal stress is
\[\frac{F}{A} = Y\alpha\,\Delta T. \tag{36.5}\]
Remarkably, the length of the rod has dropped out: a short rod and a long one develop the same stress for the same temperature change.
Example 36.4: Continuous welded rail
Modern railways often weld their rails into continuous lengths kilometers long, with no gaps at all, and anchor them firmly to the ties. Suppose a steel rail is welded in place at \(20^{\circ}\mathrm{C}\) and the sun heats it to \(50^{\circ}\mathrm{C}\). Find (a) the thermal stress in the rail and (b) the compressive force on a rail of cross-sectional area \(7.7\times 10^{-3}\,\mathrm{m^2}\). For steel, \(Y = 2.0\times 10^{11}\,\mathrm{Pa}\) and \(\alpha = 12\times 10^{-6}\,\mathrm{K^{-1}}\).
Solution
(a) Stress. From equation (36.5),
\[\frac{F}{A} = Y\alpha\,\Delta T = (2.0\times10^{11})(12\times10^{-6})(30) = \boxed{7.2\times 10^{7}\,\mathrm{Pa}} = 72\,\mathrm{MPa}.\]
(b) Force. The force is the stress times the area:
\[F = (7.2\times10^{7}\,\mathrm{Pa})(7.7\times10^{-3}\,\mathrm{m^2}) \approx \boxed{5.5\times 10^{5}\,\mathrm{N}},\]
about the weight of a \(56\,\mathrm{tonne}\) load, pushing along each rail. The stress is well below the roughly \(250\,\mathrm{MPa}\) at which ordinary steel starts to yield, so the rail is not crushed. The danger is buckling: a long, thin rail under that much compression can kink sideways, so the rails are laid at a carefully chosen “neutral” temperature and held down by heavy anchors along their whole length.
The Strange Case of Water
Water breaks the rule. Between \(0^{\circ}\mathrm{C}\) and \(4^{\circ}\mathrm{C}\) liquid water shrinks as it warms, so it is densest at \(4^{\circ}\mathrm{C}\) (Figure 36.4). Ice, in turn, is about \(8\%\) less dense than the liquid (water swells by about \(9\%\) when it freezes), which is why ice floats (Chapter 14) and why a full bottle of water left in the freezer bursts. Both oddities come from the open, hexagonal network of hydrogen bonds that water molecules form as they approach freezing (hydrogen bonds are taken up in Chapter 42).
This peculiarity is why lakes freeze from the top down, and why fish survive the winter. As autumn air cools a lake, the cooled surface water becomes denser and sinks, stirring the lake, until the whole lake reaches \(4^{\circ}\mathrm{C}\). Below that, cooling makes the surface water less dense, so it stays on top, cools further, and finally freezes into a floating lid. The ice insulates the water beneath, and the bottom of a deep lake stays near \(4^{\circ}\mathrm{C}\) all winter.
Answers to Checkpoints
Checkpoint 36.2. The hole gets larger. Heating enlarges every dimension of the washer by the same factor, like a photographic enlargement, and that includes the hole: the ring of metal around it grows in circumference, so the hole’s diameter grows too. An aluminum washer behaves the same way, but its hole grows about twice as much, because aluminum’s expansion coefficient is about twice steel’s.
Checkpoint 36.3. Brass has the larger expansion coefficient, so when heated the brass side becomes longer than the steel side. A curved strip has a longer outside edge than inside edge, so the brass ends up on the outside of the curve and the strip bends toward the steel. When cooled, the brass shrinks more, so it ends up on the inside and the strip bends the other way, toward the brass.
This page titled 36.2: Thermal Expansion was last modified on Thu, 12 Nov 2026 04:27:18 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.
The book could not be loaded just now.