25.1: Inductors

Physics: A Foundation for Scientists and Engineers · LibreTexts

0%

Contents

    Text

    Size
    100%
    Theme
    Typeface
    Line length
    Spacing

    Read aloud

    How

    Speed: 1×
    Light up
    Highlight

    Symbols: Mulberry Symbols, © 2018–2026 Steve Lee, CC BY-SA 4.0 (licence, the set), the site's own copies.

    From LibreTexts, under CC BY 4.0, as the source states it; its equations are written in TeX, which the PDF shows typeset. This page at LibreTexts.

    25.1: Inductors
    Two panels of an inductor carrying current I from a to b, showing the self-induced emf.
    Figure 25.1. The self-induced emf of an inductor always opposes the change in current. (a) When the current is increasing, the end where it enters is at the higher potential, so the inductor opposes the increase. (b) When it is decreasing, the polarity reverses, and the inductor pushes to keep the current flowing.
    Figure descriptionTwo panels, each showing an inductor, drawn as a coil symbol, between a point a on the left and a point b on the right, carrying current I from a to b. In panel a the current is increasing: the self-induced emf opposes the increase, so the left end a, where the current enters, is at the higher potential, marked plus, and b is marked minus. In panel b the current is decreasing: the induced emf tries to keep the current flowing, so the right end b is at the higher potential, marked plus, and a is marked minus.

    A current in a coil produces a magnetic field, and that field passes through the coil’s own turns. If the current changes, so does this flux, and by Faraday’s law an emf is induced in the coil itself. This self-induced emf opposes the change in current (Lenz’s law): if the current is increasing, the emf pushes against it; if it is decreasing, the emf pushes to keep it flowing (Figure 25.1).

    For a coil of \(N\) turns with flux \(\Phi_B\) through each turn, the flux is proportional to the current that produces it, so we can write \(N\Phi_B = LI\). The constant of proportionality,

    Key Equation: Self-inductance

    \[L = \frac{N\Phi_B}{I}, \tag{25.1}\]

    is the coil’s self-inductance, or simply its inductance. Like capacitance, it depends only on the geometry of the coil (and on any magnetic material inside it), not on the current. Faraday’s law then gives the self-induced emf:

    Key Equation: Emf of an inductor

    \[\mathcal{E}_L = -N\frac{d\Phi_B}{dt} = -L\frac{dI}{dt}. \tag{25.2}\]

    The SI unit of inductance is the henry (H), after the American physicist Joseph Henry, who discovered self-induction at about the same time as Faraday discovered induction: \(1\,\mathrm{H} = 1\,\mathrm{Wb/A} = 1\,\mathrm{V\cdot s/A}\). A coil with an inductance of one henry produces an emf of one volt when its current changes at one ampere per second. Practical inductors range from nanohenries in radio circuits to several henries in the power supplies of large equipment.

    A circuit element designed for its inductance is an inductor, drawn as a coil in circuit diagrams (Figure 25.1). Every circuit has some inductance, since every current makes a magnetic field; but in most circuits it is too small to matter unless the current changes very rapidly.

    Inductors in circuits. To use the loop rule (Section 21.2) with an inductor, we need the potential change across it. Crossing an inductor in the direction of the current, the potential changes by

    \[\Delta V = -L\frac{dI}{dt}. \tag{25.3}\]

    This is a drop when the current is increasing and a rise when it is decreasing, as Figure 25.1 shows. For a steady current, \(dI/dt = 0\), and an ideal inductor (one with no resistance in its wire) has no potential difference across it at all. An inductor resists changes in current, not current itself. It plays the same role for current that mass plays for velocity: it does not prevent motion, but it resists acceleration.

    The inductance of a solenoid. For a long solenoid of \(N\) turns, length \(\ell\), and cross-sectional area \(A\), the field inside is \(B = \mu_0 nI = \mu_0 NI/\ell\) (equation (23.9)), and the flux through each turn is \(\Phi_B = BA = \mu_0 NIA/\ell\). So

    \[L = \frac{N\Phi_B}{I} = \frac{\mu_0 N^2A}{\ell} = \mu_0 n^2A\ell. \tag{25.4}\]

    The inductance grows as the square of the number of turns: doubling the turns doubles both the field and the number of turns that the flux links. Filling the solenoid with iron multiplies \(L\) by the relative permeability \(1 + \chi_m\) (Section 23.7), which can be thousands, so practical inductors of large inductance are wound on iron or ferrite cores.

    Example 25.1: The inductance of a solenoid

    A solenoid \(25\,\mathrm{cm}\) long and \(2.0\,\mathrm{cm}\) in diameter is wound with 500 turns, with no core. (a) Find its inductance. (b) What emf is induced in it when its current rises steadily from zero to \(2.0\,\mathrm{A}\) in \(1.0\,\mathrm{ms}\)?

    Solution

    (a) The cross-sectional area is \(A = \pi(0.010)^2 = 3.14\times 10^{-4}\,\mathrm{m^2}\), so

    \[L = \frac{\mu_0 N^2A}{\ell} = \frac{(4\pi\times10^{-7})(500)^2(3.14\times10^{-4})}{0.25} = \boxed{0.39\,\mathrm{mH}}.\]

    (b) The current changes at \(dI/dt = (2.0\,\mathrm{A})/(1.0\times10^{-3}\,\mathrm{s}) = 2000\,\mathrm{A/s}\), so

    \[|\mathcal{E}_L| = L\frac{dI}{dt} = (3.9\times10^{-4}\,\mathrm{H})(2000\,\mathrm{A/s}) = \boxed{0.79\,\mathrm{V}}.\]

    While the current rises, this emf opposes it. Once the current is steady, the emf is zero.

    Mutual vs. Self-Inductance

    Mutual inductance: two coaxial coils, the changing field of coil 1 passing through coil 2.
    Figure 25.2. Mutual inductance. Part of the field of coil 1 passes through coil 2, so a changing current in coil 1 induces an emf in coil 2, although no wire connects them.
    Figure descriptionTwo coaxial coils side by side. Coil 1, on the left, carries a changing current I sub 1 supplied by a source. Its magnetic field lines pass through its own turns and continue through the turns of coil 2, on the right. Coil 2 is connected to a meter and has an emf script E sub 2 induced in it. No wire connects the two coils.

    Faraday’s first discovery of induction used two coils: a changing current in one induced an emf in the other. When two circuits are close enough that the field of each passes through the other, a changing current in either one induces an emf in both. The flux through coil 2 due to the current \(I_1\) in coil 1 is proportional to \(I_1\), and we write \(N_2\Phi_{21} = MI_1\) (Figure 25.2). Faraday’s law then gives the emf induced in coil 2:

    Key Equation: Mutual inductance

    \[M = \frac{N_2\Phi_{21}}{I_1}, \qquad \mathcal{E}_2 = -M\frac{dI_1}{dt}. \tag{25.5}\]

    The constant \(M\) is the mutual inductance of the two coils, also measured in henries. It depends on their sizes, their numbers of turns, and how they are placed, and it is largest when the coils share a common iron core. A remarkable result, which can be proved from the Biot–Savart law, is that the mutual inductance is the same in both directions: a changing current in coil 2 induces an emf \(\mathcal{E}_1 = -M\,dI_2/dt\) in coil 1, with the same \(M\).

    Self versus mutual. The two effects are the same physics, Faraday’s law, seen from different circuits. Self-inductance \(L\) describes the emf a coil induces in itself when its own current changes; mutual inductance \(M\) describes the emf it induces in another coil. Every coil has self-inductance; mutual inductance requires a second coil nearby. In a pair of coils, each has its own \(L\), and the pair shares one \(M\). Self-inductance is usually something to be managed, a delay or a spark to be controlled. Mutual inductance is usually the point: it is how energy and signals are passed between circuits that have no wire in common.

    Example 25.2: A coil around a solenoid

    A long solenoid of length \(0.50\,\mathrm{m}\) and cross-sectional area \(4.0\,\mathrm{cm^2}\) has 1000 turns. A small coil of 50 turns is wound tightly around its middle. (a) Find the mutual inductance. (b) What emf is induced in the small coil when the solenoid’s current changes at \(100\,\mathrm{A/s}\)?

    Solution

    (a) The solenoid’s field inside is \(B_1 = \mu_0(N_1/\ell)I_1\), and all of it passes through each turn of the small coil, so \(\Phi_{21} = B_1A\) and

    \[M = \frac{N_2\Phi_{21}}{I_1} = \frac{\mu_0N_1N_2A}{\ell} = \frac{(4\pi\times10^{-7})(1000)(50)(4.0\times10^{-4})}{0.50} = \boxed{5.0\times 10^{-5}\,\mathrm{H}}.\]

    (b) \(|\mathcal{E}_2| = M\,dI_1/dt = (5.0\times10^{-5})(100) = \boxed{5.0\,\mathrm{mV}}\). The size of the small coil does not matter, as long as it encloses the solenoid, since the solenoid’s field outside is negligible.

    Note: Mutual inductance at work

    A wireless phone charger is a flat coil in the charging pad, driven by a rapidly alternating current, and a second coil inside the phone. The changing flux of the first induces an emf in the second, which charges the battery. Electric toothbrushes, implanted medical devices such as pacemakers and cochlear implants, and the contactless payment cards held near a reader all receive energy or data the same way. The coupling works only over short distances, because the field of a coil falls off rapidly, as the field of a dipole does (Section 23.3).

    Checkpoint 25.1

    (a) A solenoid’s number of turns is doubled, keeping its length and area the same. By what factor does its inductance change? (b) Two coils are placed side by side. How could you arrange them to make their mutual inductance as small as possible?

    Answer

    Answers to Checkpoints

    Checkpoint 25.1. (a) The inductance of a solenoid, \(L = \mu_0N^2A/\ell\), goes as \(N^2\): doubling the turns doubles the field each turn produces and doubles the number of turns that field threads, so \(L\) quadruples. (b) Minimize the flux of one coil that passes through the other: place them with their axes perpendicular, so the field of one runs across, not through, the turns of the other, and move them as far apart as possible.


    This page titled 25.1: Inductors was last modified on Thu, 12 Nov 2026 04:27:15 GMT and is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by Michael Ragsdale.