Opening the book…
Signal Integrity (SI) refers to the quality of electrical signals as they travel through traces, vias, and components on a printed circuit board. Ensuring good signal integrity is critical for high-speed and high-frequency designs. Poor signal quality can lead to data errors, signal distortion, and system malfunction.[1]
All signals are subject to effects such as noise, distortion, and loss. Over short distances and at low bit rates, a simple conductor can transmit this with sufficient fidelity. However, at high bit rates and over longer distances or through various mediums, various effects can degrade the electrical signal to the point where errors occur and the system or device fails. Signal integrity engineering is the task of analyzing and mitigating these effects.[1] The system design team member who has responsibility for this analysis usually has a job title of Signal Integrity Engineer.
On printed circuit boards, signal integrity became a serious concern when the transition (rise and fall) times of signals started to become comparable to the propagation time across the board. This typically happens when system speeds exceed a few tens of MHz. At first, only a few of the most important, or highest speed, signals needed detailed analysis or design. As speeds increased, a larger and larger fraction of signals needed SI analysis and design practices. In modern (> 100 MHz) circuit designs, essentially all signals must be designed with SI in mind.[1]
Factors Affecting Signal Integrity
The following is a list of factors that affect signal integrity:[1]
- Reflection
- Crosstalk
- Transmission Line Effects
- Impedance Mismatch
- Electromagnetic Interference (EMI)
- Power Integrity (PI)
- Rise and Fall Time
A PCB designer removes signal integrity problems through the use of the following mitigation techniques:[1]
- Placing a solid reference plane adjacent to the signal traces to control crosstalk
- Controlling the trace width spacing to the reference plane to create consistent trace impedance
- Using terminations to control ringing
- Route traces perpendicular on adjacent board layers to reduce crosstalk
- Increasing spacing between traces to reduce crosstalk
- Providing sufficient ground (and power) connections to limit "ground bounce" (this sub-discipline of signal integrity is sometimes called out separately as power integrity)
- Distributing power with solid plane layers to limit power supply noise
- Adding a pre-emphasis filter to the transmitter driving cell
Cross-talk
Crosstalk (XT) is a phenomenon by which a signal transmitted on one circuit or channel of a transmission system creates an undesired effect in another circuit or channel. Crosstalk is usually caused by undesired capacitive, inductive, or conductive coupling from one circuit or channel to another.[3]
Eye-patterns
If you were to go to a hardware bring-up lab and observe a signal integrity engineer at work, you likely would encounter the engineer analyzing an eye pattern on an oscilloscope.
An eye pattern, or eye diagram, is a display on an oscilloscope screen in which a digital signal from a receiver is repetitively sampled and applied to the vertical input (y-axis), while the data rate is used to trigger the horizontal sweep (x-axis). It is called an eye pattern because, for several types of coding, the pattern looks like a series of eyes between a pair of rails. The eye pattern a tool for the evaluation of the combined effects of channel noise, dispersion and inter-symbol interference on the performance of a baseband pulse-transmission system.[5]
A symbol is a waveform, a state or a significant condition of the communication channel that persists, for a fixed period of time.[6]
inter-symbol interference (ISI) is a form of distortion of a signal in which one symbol (waveform) interferes with subsequent symbols (waveforms). This is an unwanted phenomenon as the previous symbols (waveforms) have a similar effect as noise, thus making the communication less reliable.[7]
Several system performance measurements can be derived by analyzing the display. If the signals are too long, too short, poorly synchronized with the system clock, too high, too low, too noisy, or too slow to change, or have too much undershoot or overshoot, this can be observed from the eye diagram. An open eye pattern corresponds to minimal signal distortion. Distortion of the signal waveform due to inter-symbol interference and noise appears as closure of the eye pattern.[5]
Noise is an error or undesired random disturbance of a useful information signal in a communication channel.[8]
Figure \(\PageIndex{1}\): Example of an Eye Diagram. (By Gmoose1 - Own work, CC BY-SA 3.0[4])
Graphical eye pattern showing an example of two power levels in an OOK modulation scheme. Constant binary 1 and 0 levels are shown, as well as transitions from 0 to 1, 1 to 0, 0 to 1 to 0, and 1 to 0 to 1 in a sinusoidal pattern.
Manhattan lengths of signal traces
Manhattan length (or distance), refers to the total distance traveled by a trace on a printed circuit board when following a grid pattern (like streets on Manhattan Island, New York), calculated by summing the horizontal and vertical distances between two points.
Manhattan length helps printed circuit board designers to optimize trace routing and maintain good signal integrity.
Pre-emphasis settings
Pre-emphasis is a technique to protect against anticipated noise and loss. The idea is to boost (and hence distort) the frequency range that is most susceptible to noise and loss beforehand, so that after a noisy and lossy process more information can be recovered from that frequency range. Removal of the distortion caused by pre-emphasis is called de-emphasis, making the output accurately reproduce the original input.[2]
In serial data transmission, emphasis is used to improve signal quality at the output of a communication channel. In transmitting signals at high data rates, the transmission medium may introduce distortions, so emphasis is used to distort the transmitted signal to correct for this distortion. This produces a received signal that more closely resembles the original or desired signal, allowing the use of higher data rates or producing fewer bit errors. Most real world channels have loss that increases with frequency (effectively a low pass filter), so emphasis needs to invert this effect (functioning as a high pass filter).[2]
Emphasis can be implemented either by boosting high frequencies (pre-emphasis, increasing the amplitude of transition bits) or attenuating low frequencies (de-emphasis, reducing the amplitude of non-transition bits). Both have the same net effect of producing a flatter system frequency response. De-emphasis is typically more convenient to do in real circuits since it only requires attenuation rather than amplification.[2]
In practice, after a signal integrity engineer conducts the requisite analysis, a set of needed pre-emphasis settings is calculated and saved in a file. This file is then referenced when the system is operational to ensure that the intended pre-emphasis actions are performed.
References
- Signal integrity - Wikipedia. Accessed February 16, 2026.
- Emphasis (telecommunications) - Wikipedia. Accessed February 16, 2026. Text is available under the Creative Commons Attribution-ShareAlike 4.0 License; additional terms may apply. By using this site, you agree to the Terms of Use and Privacy Policy. Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc., a non-profit organization.
- Crosstalk - Wikipedia. Accessed February 16, 2026.
- By Gmoose1 - Own work, CC BY-SA 3.0, Wikimedia Eye pattern diagram. [Eye pattern diagram in Wikipedia-Eye pattern.] Accessed February 16, 2026.
- Eye pattern - Wikipedia. Accessed February 17, 2026.
- Symbol rate - Wikipedia. Accessed February 17, 2026.
- Intersymbol interference - Wikipedia. Accessed February 17, 2026.
- Noise (electronics) - Wikipedia. Accessed February 17, 2026.
4.4.4: Signal integrity is shared under a CC BY 4.0 license and was authored, remixed, and/or curated by LibreTexts.
The book could not be loaded just now.