Opening the book…
- Overview with Terms
- Stress – Internal material response as shear or normal force \(F\) per unit area \(A_{c}\):
\(\sigma= \frac{F}{A_{c}}\) - Strain – Elongation \(\partial L\) of material relative to unloaded length \(L\):
\(\varepsilon = \frac{\partial L}{L}\) - Stress–strain relationship - when in elastic regime with linear slope that does not permanently deform material:
\(\sigma = E_{m} \varepsilon\)
where \(E_{m}\) is Young's Modulus.
- Stress – Internal material response as shear or normal force \(F\) per unit area \(A_{c}\):
- Single Strain Gage
- Local elongation measurable with strain gage
- Transduction via resistance in a wire: rate of flow of electrons through conductive wire:
\[R = \frac{\rho_{e} L}{A}\] where \(R\) is total resistance, \(\rho_{e}\) is resistivity based on material property, \(L\) is length of wire, and \(A\) indicates the cross sectional area. Applying the full differential:
\[\frac{dR}{R} = \frac{d\rho_{e}}{\rho_{e}} + \frac{dL}{L} - \frac{dA}{A}\] which can then incorporate Poisson's ratio \(\nu_{p}\) for relative decrease in area due to elongation
\[\frac{dR}{R} = \frac{d\rho_{e}}{\rho_{e}} + \frac{dL}{L}(1+2\nu_{p})\] - Gage factor (GF): reduce complexity to simple scaling factor instead of combination of material properties:
\(GF = \frac{\partial R/R}{\varepsilon}\) - Localized measurement: strain is a local feature based on the local stress; if local stress changes due to force or area changes, corresponding changes to \(\varepsilon\) will be observed.
- Resistance Measurement in Electronics
- Wheatstone Bridge: tool to connect gages in mechanism that one can calculate input voltage \(E_{i}\) and output voltage \(E_{o}\) relative to changes in resistance \(R_{location}\)
\[E_{o} = E_{i} \left(\frac{R_1}{R_1 + R_2} - \frac{R_3}{R_3 + R_4}\right)\] - Single resistor change: assuming an originally balanced bridge \(R_{1} = R_{2} = R_{3} = R_{4}\), the incremental output voltage \(\delta E_{o}\) is a function of small change in resistance \(\delta R\):
\[\frac{\delta E_o}{E_i} = \frac{\delta R / R}{4 + 2 \delta R / R}\] -
Given a 1 cm x 3 cm bar with Youngs Modulus of \(200 \times 10^6\) kN/m³ has an axial force of 35 kN applied.
The strain gage has nominal resistance of 120 \(\Omega\) and gage factor of 2.15. When input voltage is 9 V determine the output voltage \(E_{o}\)
- Answer
-
Cross sectional area of axial load: \(A_{c} = l \times w = 0.01 \times 0.03 = 3\times 10^{-4}\) m\(^{2}\)
Stress calculation: \(\sigma = \frac{F}{A_{c}}= \frac{35\times 10^{3}}{3\times 10^{-4}} = 1.167 \times 10^{8}\) N/m\(^{3}\)
Strain via the Elastic Modulus: \(\varepsilon = \frac{\sigma}{E_{m}} = 5.83 \times 10^{-4} \)
Incremental change in resistance: \(\delta R = GF\ R \ \varepsilon = 2.15(120)5.83\times 10^{-4} = 0.1505 \Omega\)
Output voltage: \(\delta E_{o} = E_{i}\left(\frac{GF\ \varepsilon}{4+2GF\ \varepsilon}\right) = 2.82\) mV
- Wheatstone Bridge: tool to connect gages in mechanism that one can calculate input voltage \(E_{i}\) and output voltage \(E_{o}\) relative to changes in resistance \(R_{location}\)
- Bending Stress on a Beam
- Shear and moment review
- Shear force from distributed load:
\[V(x) = -\int W(x) dx\] - Bending moment:
\[M(x) = \int V(x) dx\] - Bending stress:
\[\sigma = \frac{-M}{I}z\]
where \(z\) is distance from centroid.
- Shear force from distributed load:
- Examples of Shear-Moment Diagrams described within lecture
- Cantilever beam with load \(P\)
- Uniform load \(W\) over span \(0.6H\)
- Linearly decreasing load over \(2B\)
- Four-point and three-point bending examples
- Shear and moment review
8.2: Stress and strain is shared under a CC BY-NC 4.0 license and was authored, remixed, and/or curated by LibreTexts.
The book could not be loaded just now.