Opening the book…
After completing this section, you should be able to
- draw the Fischer projection of a monosaccharide, given its wedge and dash structure or a molecular model.
- draw the wedge and dash structure of a monosaccharide, given its Fischer projection or a molecular model.
- construct a molecular model of a monosaccharide, given its Fischer projection or wedge and dash structure.
Make certain that you can define, and use in context, the key term below.
- Fischer projection
When studying this section, use your molecular model set to assist you in visualizing the structures of the compounds that are discussed. It is important that you be able to determine whether two apparently different Fischer projections represent two different structures or one single structure. Often the simplest way to check is to construct a molecular model corresponding to each projection formula, and then compare the two models.
Drawing Representations of 3D Structures
The problem of drawing three-dimensional configurations on a two-dimensional surface, such as a piece of paper, has been a long-standing concern of chemists. The wedge and dash notations we have been using are effective, but can be troublesome when applied to compounds having many chiral centers. As part of his Nobel Prize-winning research on carbohydrates, the great German chemist Emil Fischer, devised a simple notation that is still widely used. Fischer Projections allow us to represent 3D molecular structures in a 2D environment without changing their properties and/or structural integrity.

Below in Figure \(\PageIndex{1}\) are different representations of (R)-glyceraldehyde, the smallest sugar molecule (also called D-glyceraldehyde in the stereochemical nomenclature used for sugars):
Fischer projections show sugars in their open-chain form. In a Fischer projection, the carbon atoms of a sugar molecule are connected vertically by solid lines, while carbon-oxygen and carbon-hydrogen bonds are shown horizontally. Stereochemical information is conveyed by a simple rule: vertical bonds point into the plane of the page, while horizontal bonds point out of the page.

The Fisher structures of the most common monosaccharides (other than glyceraldehyde and dihydroxyacetone), which you will encounter most frequently, are shown below.
How to Draw Fischer Projections
A Fischer projection or Fischer projection formula is a convention used to depict a stereoformula in two dimension without destroying the stereochemical information, i.e., absolute configuration, at chiral centers. To make a Fischer Projection, it is easier to show through examples than through words. Let's start with the first example, turning a 3D structure of (R)-Lactic acid into a 2D Fischer Projection.
To convert this stereoformula into a Fischer projection use the following procedure:
|
(R)-Lactic acid:
Step 1: Hold the molecule so that
|
![]() |
|
Step 2: Push the two bonds coming out of the plane of the paper onto the plane of the paper. |
![]() |
| Step 3: Pull the two bonds going into the plane of the paper onto the plane of the paper. | ![]() |
|
Step 4: Omit the chiral atom symbol for convenience. |
![]() |
How to Draw Wedge and Dash Structures from Fischer Projections
Sugars can be drawn in the straight chain form as either Fisher projections or perspective structural formulas. Below in Figure \(\PageIndex{2}\) are Fisher projections and perspective structural representation of (R)-glyceraldehyde (D-glyceraldehyde):
In the Fisher projection, the vertical bonds point down into the plane of the paper. That's easy to visualize for 3C molecules. but more complicated for bigger molecules. For those draw a wedge and dash line drawing of the molecule. When determining the orientation of the hydroxides on each C, orient the wedge and dash drawing in your mind so that the C atoms adjacent to the one of interest are pointing down. Sighting towards the carbonyl C, if the OH is pointing to the right in the Fisher project, it should be pointing to the right in the wedge and dash drawing, as shown below for D-erthyrose.

Determining R and S in Fischer Projections
Determining whether a chiral carbon is R or S may seem difficult when using Fischer projections, but it is actually quite simple. If the lowest priority group (often a hydrogen) is on a vertical bond, the configuration is given directly from the relative positions of the three higher-ranked substituents. If the lowest priority group is on a horizontal bond, the positions of the remaining groups give the wrong answer (you are in looking at the configuration from the wrong side), so you simply reverse it.

Worked Example \(\PageIndex{1}\)
Determine if carbon #2 in D-glucose is R or S.

- Answer
-
When deciding whether a stereocenter in a Fischer projection is R or S, realize that the hydrogen, in a horizontal bond. Therefore, the orientation of the three remaining substituents is reversed to create the correct answer or a counterclockwise circle means R, and a clockwise circle means S. For carbon #2 in D-Glucose substituent 1, 2, and 3 form a counterclockwise circle so the carbon is R.

Determining Isomeric Relationships in Fischer Projections
Fischer projections are useful when looking at many different diastereomeric sugar structures, because the eye can quickly pick out stereochemical differences according to whether a hydroxyl group is on the left or right side of the structure.

The usefulness of this notation to Fischer, in his carbohydrate studies, is evident in the following diagram. There are eight stereoisomers of 2,3,4,5-tetrahydroxypentanal, a group of compounds referred to as the aldopentoses (aldo- since the oxidized carbon is an aldehyde and -pentose since the molecules contain 5 carbons). Since there are three chiral centers in this constitution, we should expect a maximum of 23 stereoisomers. These eight stereoisomers consist of four sets of enantiomers. If the configuration at C-4 is kept constant (R in the examples shown here), the four stereoisomers that result will be diastereomers.

The aldopentose structures drawn above are all diastereomers. A more selective term, epimer, is used to designate diastereomers that differ in configuration at only one chiral center. Thus, ribose and arabinose are epimers at C-2, and arabinose and lyxose are epimers at C-3. However, arabinose and xylose are not epimers, since their configurations differ at both C-2 and C-3.
Convert each of the following Fischer projections into a tetrahedral representation and assign R or S stereochemistry:
b.
c.
- Answer
-
a. S b. R c. S
Which of the following Fischer projections of glyceraldehyde represent the same enantiomer?
(a)
(b)
(c)
(d)
- Answer
-
A, B, and C are the same.
Redraw the following molecule as a Fischer projection, and assign R or S configuration to the chirality center (green = Cl):

- Answer
-

Redraw the following aldotetrose as a Fischer projection, and assign R or S configuration to each chirality center:

- Answer
-
Draw 'zigzag' structures (using the solid/dash wedge convention to show stereochemistry) for the following sugars. Label all stereocenters R or S.
a) D-ribose, b) D-arabinose, c) D-xylose, d) D-lyxose.
- Answer


This page titled 11.2: Depicting Carbohydrate Stereochemistry - Fischer Projections was last modified on Thu, 17 Apr 2025 21:42:30 GMT and is shared under a CC BY-NC-SA 4.0 license and was authored, remixed, and/or curated by Sol Parajon Puenzo (Cañada College) .
The book could not be loaded just now.




