Opening the book…
1. Always wear chemical splash goggles while working on this experiment.
2. Wearing gloves, especially when working with silver nitrate, is advisable, as it can cause skin stains. Be sure to thoroughly wash your hands after completing this experiment.
3. Exercise caution when working with Bunsen burners. Keep notebooks, purses, books, and other equipment away from open flames. Follow all directions provided by your instructor when heating test tubes.
4. Thoroughly read and reread the bottles' labels to ensure you mix the appropriate solutions.
5. Dispose of chemical waste in the designated waste containers, as instructed by your instructor.
6. Thoroughly clean your work area and return chemicals and equipment to their designated places after the experiment.
EQUIPMENT* AND CHEMICALS NEEDED
| EQUIPMENT | EQUIPMENT | CHEMICALS | CHEMICALS |
|---|---|---|---|
| 10 mL Graduated Cylinder | 5 Medium-sized Test Tubes, Test Tube Rack, and a Test Tube Holder | Solid Magnesium and Zinc | 0.5 M Or 1.0 M solutions of CuSO4, AgNO3, NaCl, CaCl2, Na3PO4, BaCl2, Na2SO4, NaOH, FeCl3 |
| Bunsen Burner with Hose | Well Plate | Solid CuSO4. 5H2O | 1 M HCl |
| Matches, lighter, or Striker. | Spatula | Copper Wire | Solid NaHCO3 |
| Wire Cutters or Scissors | 600 mL Beaker | Solid Waste Container | Inorganic Waste Container |
* Images of equipment needed in this lab can be found in the appendix (the equipment may differ or be subject to changes; follow your instructor’s directions).
EXPERIMENTAL PROCEDURE
Part A: Decomposition Reactions
- Gather the following equipment and assemble the Bunsen burner.
- Bunsen burner with the hose, matches or lighter, test tube holder, test tube rack, and two medium-sized test tubes.
- Take two medium-sized test tubes. Add a small scoop of solid NaHCO3 (baking soda) to the first medium-sized test tube and a small scoop of solid CuSO4 · 5H2O to the second medium-sized test tube. Note: Rinse and dry your spatula between obtaining the two solids to avoid cross-contamination.
- Using a test tube holder, place the tip of the test tube containing NaHCO3 into the flame for a few minutes. Hold the test tube at an angle, ensuring the open end is not pointed towards you or your lab partners. Record any observations.
- Using a test tube holder, place the tip of the test tube containing CuSO4 · 5H2O into the flame for a few minutes. Hold the test tube at an angle, ensuring the open end is not pointed towards you or your lab partners. Record any observations.
- Turn off the burner. After the remaining solids in the test tubes have cooled, pour them into the inorganic waste container. Clean your work area and all glassware before proceeding to the next step of the experiment.
Do not place your hot test tubes in the plastic test tube rack. If you have a plastic test tube rack, place the test tube in a glass beaker until it cools to room temperature.
Part B: Single Displacement Reactions
- Take five test tubes, add a small scoop or piece of Mg (s), Zn (s), and Cu (s) to three separate test tubes, a small scoop or piece of Zn (s) to the fourth test tube, and a small piece of cu (copper wire) to the fifth test tube. Secure the test tubes in the test tube rack.
- Add approximately 2.0 mL of 1.0 M HCl into the FIRST THREE test tubes ONLY and record your observations.
- Into the fourth test tube, add a small scoop of Zn(s) and enough CuSO4 solution to completely cover the Zn(s). Record your initial observation and then your observations after 15 minutes and 30 minutes. (While waiting, you can work on Part C)
- Using a small piece of copper wire, add enough AgNO3 solution to completely cover the Cu (s) in the fifth test tube. Record your initial observation and then your observations after 15 and 30 minutes.
- Leave the test tubes in the rack, and after the 30-minute observation, pour out the contents of the test tubes into a 600 mL beaker. Using forceps, remove any unreacted metal and place it on a paper towel. Place the solution in the inorganic waste container, and dry the unreacted metal in the metal waste container. Clean and dry the test tubes.
Part C: Double Displacement Reactions
1. Obtain a well plate, and add 5-10 drops of each solution to the following wells:
Well 1: NaCl and AgNO3
Well 2: CaCl2 and Na3PO4
Well 3: BaCl2 and Na2SO4
Well 4: CuSO4 and Na3PO4
Well 5: CuSO4 and NaOH
Well 6: FeCl3 and NaOH
Well 7: CaCl2 and Na2SO4
Well 8: FeCl3 and Na2SO4
2. Record your observations in the data table, part C. Pour the contents of the well plate into a 600.0 mL beaker. The contents of the 600 mL beaker should then be poured into the inorganic waste container.
3. Thoroughly clean all glassware and the well plate with soap and water. Return all equipment and chemicals to their appropriate places. Clean your work area before leaving the lab.
6.1: Chemical Reactions and Equations - Experiment is shared under a not declared license and was authored, remixed, and/or curated by LibreTexts.
The book could not be loaded just now.